Minnesota Pollution Control Agency Logo

Minnesota Stormwater Manual

Difference between revisions of "Fact sheet for filtration"

m
 
(8 intermediate revisions by the same user not shown)
Line 23: Line 23:
  
 
==Description==
 
==Description==
−
<p>[[Glossary#F|Filtration]] systems vary in their operation and applicability, but all can be described as structural BMPs that function mainly to enhance water quality by passing stormwater through a media. The media can be made of sand, peat, grass, soil, compost or vegetation and should be assigned on a case-by-case basis. Filters can be off-line systems or designed as [[Glossary#P|pre-treatment]] before discharging to other stormwater features.</p>
+
[[Glossary#F|Filtration]] systems vary in their operation and applicability, but all can be described as structural BMPs that function mainly to enhance water quality by passing stormwater through a media. The media can be made of sand, peat, soil, or compost and should be assigned on a case-by-case basis. Filters can be off-line systems or designed as [[Glossary#P|pre-treatment]] before discharging to other stormwater features.
−
<p>The two main categories of filtration systems include: media filters, and vegetated filters. [[Glossary#M|media filters]] can be located on the surface, underground, along the perimeter or an area, or in what is called a pocket design. Vegetated channels may be grass channels, dry or wet [[Glossary#S|swales]], submerged gravel wetlands, or filter strips.</p>
+
 
 +
[[Glossary#M|Media filters]] can be located on the surface, underground, along the perimeter or an area, or in what is called a pocket design.
  
 
[[file:Filtration-stormevent.jpg|thumb|300px|alt=Drawing of the start of Storm Event - Initial runoff & storage|Drawing of the start of Storm Event - Initial runoff & storage]]
 
[[file:Filtration-stormevent.jpg|thumb|300px|alt=Drawing of the start of Storm Event - Initial runoff & storage|Drawing of the start of Storm Event - Initial runoff & storage]]
 
[[file:Filtration-storage.jpg|thumb|300px|alt=Drawing of the Duration of Storm Event - Storage & filtration/infiltration|Drawing of the Duration of Storm Event - Storage & filtration/infiltration]]
 
[[file:Filtration-storage.jpg|thumb|300px|alt=Drawing of the Duration of Storm Event - Storage & filtration/infiltration|Drawing of the Duration of Storm Event - Storage & filtration/infiltration]]
 
[[file:Infiltration.jpg|thumb|300px|alt=Drawing of the Following Storm Event - Remaining storage drawdown|Drawing of the Following Storm Event - Remaining storage drawdown]]
 
[[file:Infiltration.jpg|thumb|300px|alt=Drawing of the Following Storm Event - Remaining storage drawdown|Drawing of the Following Storm Event - Remaining storage drawdown]]
−
 
−
==Management suitability==
 
−
*Water Quality (V<sub>wq</sub>) = High
 
−
*Channel Protection (V<sub>cp</sub>) = Med.
 
−
*Overbank Flood Protection (V<sub>p10</sub>) = Low
 
−
*Extreme Flood Protection (V<sub>p100</sub>) = Low
 
−
*Recharge Volume (V<sub>re</sub>) = Med./ Low
 
  
 
==Mechanisms==
 
==Mechanisms==
−
*[[Glossary#I|Infiltration]] with appropriate soil & site conditions
+
*[[Glossary#I|Infiltration]] with raised underdrain
 
*Screening/ [[Glossary#F|Filtration]]
 
*Screening/ [[Glossary#F|Filtration]]
 
*[[Glossary#E|Evaporation]]
 
*[[Glossary#E|Evaporation]]
Line 46: Line 40:
  
 
==Pollutant removal==
 
==Pollutant removal==
−
*70 to 85 percent [[Glossary#T|Total Suspended Solids (TSS)]]
+
Pollutant removal varies with the design, construction and maintenance of the BMP. Values below are approximately mid-range removals for a standard designed BMP that is properly constructed and maintained.
−
*0 to 50 percent/35 percent Nutrients - [[Glossary#T|Total Phosphorus]] /Total Nitrogen
+
 
−
*45 to 85 percent Metals - Cadmium, Copper, Lead, and Zinc
+
Media filter
−
*35 percent Pathogens - Coliform, Streptococci, E. Coli
+
*85 percent [[Glossary#T|Total Suspended Solids (TSS)]]
−
*80 percent Toxins - Hydrocarbon
+
*50 percent/35 percent Nutrients - [[Glossary#T|Total Phosphorus]] /Total Nitrogen
 +
*40 to 80 percent Metals - Cadmium, Copper, Lead, and Zinc (will vary with metal)
 +
*35 percent Coliform, Streptococci, E. Coli
 +
*80 percent Hydrocarbon
 +
 
 +
Vegetative filter
 +
*68 percent [[Glossary#T|Total Suspended Solids (TSS)]]
 +
*40 percent/35 percent Nutrients - [[Glossary#T|Total Phosphorus]] /Total Nitrogen
 +
*40 to 80 percent Metals - Cadmium, Copper, Lead, and Zinc (will vary with metal)
 +
*0 percent Coliform, Streptococci, E. Coli
 +
*80 percent Hydrocarbon
  
 
==Site factors==
 
==Site factors==
−
*5 acre maximum Drainage Area
+
*The RECOMMENDED maximum drainage area is typically 5 acres, but can be greater if the discharge to the basin has received adequate pretreatment and the basin is properly designed, constructed, and maintained.
 
*20 percent maximum Site Slope
 
*20 percent maximum Site Slope
−
*3 feet minimum Depth to Bedrock
+
*3 feet minimum Depth to Bedrock unless lined
−
*3 feet minimum Depth to Seasonally High Water Table
+
*3 feet minimum Depth to Seasonally High Water Table unless lined
 
*A,B,C,D - NRCS Soil Type
 
*A,B,C,D - NRCS Soil Type
 
*Poor to Good Freeze/ Thaw Suitability
 
*Poor to Good Freeze/ Thaw Suitability
−
*Suitable with impermeable liner - Potential [[Glossary#H|Hotspot]] Runoff
+
*Suitable with impermeable liner - [[Glossary#H|Hotspot]] Runoff
 +
 
 +
[[Category:Level 3 - Best management practices/Structural practices/Dry swale]]
 +
[[Category:Level 3 - Best management practices/Structural practices/Green roof‏‎]]
 +
[[Category:Level 3 - Best management practices/Structural practices/Iron enhanced sand filter‏‎]]
 +
[[Category:Level 3 - Best management practices/Structural practices/Sand filter, iron enhanced sand filter, media filter]]
 +
[[Category:Level 3 - Best management practices/Structural practices/Step pool]]
 +
[[Category:Level 3 - Best management practices/Structural practices/Wet swale]]

Latest revision as of 22:39, 3 December 2022

Filtration practices are structural stormwater controls that capture, temporarily store, and route stormwater runoff through a filter bed to improve water quality.

Photo of a swale at Lino Lakes city hall
Photo of a swale at Lino Lakes city hall
Photo of a Swale city of Woodbury MN
Photo of a Swale city of Woodbury MN

Design criteria

  • Ensure adequate space for Filtration system
  • Some installations require 2 to 6 feet of head
  • Removal potential of the key pollutant
  • Parent material and potential for ground water contamination

Benefits

  • Good for highly impervious areas with low sediment/high pollutant load (e.g. urban land use and retrofit scenarios)
  • High pollutant removal rates
  • May be used in a variety of soil types
  • Good for the treatment of hotspots because it can be isolated from groundwater by using a liner if contamination concerns exist

Limitations:

  • Higher maintenance requirements
  • Some installations (media filters) have higher construction costs
  • Minimal treatment of soluble nutrients
  • Potential for nitrification in media filters where anaerobic conditions exist

Description

Filtration systems vary in their operation and applicability, but all can be described as structural BMPs that function mainly to enhance water quality by passing stormwater through a media. The media can be made of sand, peat, soil, or compost and should be assigned on a case-by-case basis. Filters can be off-line systems or designed as pre-treatment before discharging to other stormwater features.

Media filters can be located on the surface, underground, along the perimeter or an area, or in what is called a pocket design.

Drawing of the start of Storm Event - Initial runoff & storage
Drawing of the start of Storm Event - Initial runoff & storage
Drawing of the Duration of Storm Event - Storage & filtration/infiltration
Drawing of the Duration of Storm Event - Storage & filtration/infiltration
Drawing of the Following Storm Event - Remaining storage drawdown
Drawing of the Following Storm Event - Remaining storage drawdown

Mechanisms

Pollutant removal

Pollutant removal varies with the design, construction and maintenance of the BMP. Values below are approximately mid-range removals for a standard designed BMP that is properly constructed and maintained.

Media filter

  • 85 percent Total Suspended Solids (TSS)
  • 50 percent/35 percent Nutrients - Total Phosphorus /Total Nitrogen
  • 40 to 80 percent Metals - Cadmium, Copper, Lead, and Zinc (will vary with metal)
  • 35 percent Coliform, Streptococci, E. Coli
  • 80 percent Hydrocarbon

Vegetative filter

  • 68 percent Total Suspended Solids (TSS)
  • 40 percent/35 percent Nutrients - Total Phosphorus /Total Nitrogen
  • 40 to 80 percent Metals - Cadmium, Copper, Lead, and Zinc (will vary with metal)
  • 0 percent Coliform, Streptococci, E. Coli
  • 80 percent Hydrocarbon

Site factors

  • The RECOMMENDED maximum drainage area is typically 5 acres, but can be greater if the discharge to the basin has received adequate pretreatment and the basin is properly designed, constructed, and maintained.
  • 20 percent maximum Site Slope
  • 3 feet minimum Depth to Bedrock unless lined
  • 3 feet minimum Depth to Seasonally High Water Table unless lined
  • A,B,C,D - NRCS Soil Type
  • Poor to Good Freeze/ Thaw Suitability
  • Suitable with impermeable liner - Hotspot Runoff
Retrieved from "https://stormwater.pca.state.mn.us/index.php?title=Fact_sheet_for_filtration&oldid=63329"

This page was last edited on 3 December 2022, at 22:39.