|
|
| (3 intermediate revisions by the same user not shown) |
| Line 1: |
Line 1: |
| − | {{alert|''Reference to specific commercial products, processes, or services by trade name, trademark, service mark, manufacturer, or otherwise does not constitute or imply endorsement, recommendation, or favoring by the Minnesota Pollution Control Agency. ''|alert-info}}
| + | See [[Contech MWS-Linear Modular Wetland]] |
| − | | |
| − | CONTECH Engineered Solutions, LLC. MWS-Linear Modular Wetland is an engineered filtration system designed to filter pollutants from stormwater runoff. It is classified as a <span title="A manufactured treatment device (mtd) is a pre-fabricated stormwater treatment structure utilizing settling (sedimentation), filtration, absorptive/adsorptive materials, vortex separation, vegetative components, and/or other appropriate technology to remove pollutants from stormwater runoff. MTDs are typically proprietary devices."> '''manufactured treatment device'''</span> (mtd).
| |
| − | | |
| − | This page provides information on pollutant removal credits for Contech MWS-Linear Modular Wetland, links to supporting information, and links to information on system design, inspection, operation, and maintenance.
| |
| − | | |
| − | ==TP and TSS credits==
| |
| − | When conditions described in this section are met, applicable Contech MWS-Linear Modular Wetland systems are approved for the following removals for total suspended solids (TSS) and total phosphorus (TP).
| |
| − | *TSS: 80 percent removal
| |
| − | *TP: Tier 1
| |
| − | **Credit: 50 percent removal
| |
| − | **Conditions for receiving credit
| |
| − | ***Inspect manufactured treatment device a minimum of twice during year 1. Conduct inspections following manufacturer’s instructions/recommendations and any additional instructions [https://stormwater.pca.state.mn.us/index.php?title=BioClean_MWS-Linear_Modular_Wetland#Use_conditions listed in this section]. Use maintenance indicators provided by manufacturers to determine if maintenance is needed. Maintenance procedures should follow manufacturer’s guidelines. After year 1, follow manufacturers inspection, operation, and maintenance schedule and procedures unless otherwise required or unless year 1 inspections indicate a need for increased inspection and/or operation and maintenance.
| |
| − | ***Comply with appropriate configurations and Use conditions from TAPE.
| |
| − | ***Comply with [https://stormwater.pca.state.mn.us/index.php?title=BioClean_MWS-Linear_Modular_Wetland#Configurations appropriate configurations in the Design Manual] and [https://stormwater.pca.state.mn.us/index.php?title=BioClean_MWS-Linear_Modular_Wetland#Use_conditions Use conditions]
| |
| − | *TP: Tier 2
| |
| − | **Credit: 53 percent removal
| |
| − | **Conditions for receiving credit
| |
| − | ***Must meet Tier 1 conditions.
| |
| − | ***DP should be 25 percent or less of TP. For a discussion of conditions where DP is likely to exceed 25% of TP, [https://stormwater.pca.state.mn.us/index.php?title=TP_and_TSS_credits_and_guidance_for_manufactured_treatment_devices_(mtds)#Applicability_of_Tier_2_TP_credits link here]. TP removal should be adjusted when DP fractions exceed 25%, as described at the link provided above.
| |
| − | ***Inspect manufactured treatment device monthly during the frost free season for the first year of operation after construction. Conduct inspections following manufacturer’s instructions/recommendations. Use maintenance indicators provided by manufacturers to determine if maintenance is needed. Maintenance procedures should follow manufacturer’s guidelines. Determine future inspection and maintenance schedules from findings during the first year of operation.
| |
| − | *TP: Tier 3 - no Tier 3 credit at this time
| |
| − | | |
| − | For more information on credits, see [[TP and TSS credits and guidance for manufactured treatment devices (mtds)]]
| |
| − | | |
| − | ===Configurations===
| |
| − | For a discussion of Contech MWS-Linear Modular Wetland configurations see [https://stormwater.pca.state.mn.us/index.php?title=BioClean_MWS-Linear_Modular_Wetland#Configurations appropriate configurations in the design, installation, and specification documents].
| |
| − | | |
| − | ===Use conditions===
| |
| − | To receive the full credit, Contech MWS-Linear Modular Wetland systems must comply with the following conditions.
| |
| − | #Design, assemble, install, operate, and maintain Contech MWS-Linear Modular Wetland systems in accordance with applicable [https://stormwater.pca.state.mn.us/index.php?title=BioClean_MWS-Linear_Modular_Wetland#Links manuals].
| |
| − | #The maximum flow rates through the devices are specified below.
| |
| − | ##Sized at a hydraulic loading rate of:
| |
| − | ###1 gallon per minute (gpm) per square foot (sq ft) of Wetland Cell Surface Area
| |
| − | ###Prefilter box (approved at either 22 inches or 33 inches tall)
| |
| − | ###3.0 gpm/sq ft of prefilter box surface area for moderate pollutant loading rates (low to medium density residential basins).
| |
| − | ###2.1 gpm/sq ft of prefilter box surface area for high p
| |
| − | #Systems are designed to treat a specified water quality volume or annual average runoff volume. The annual average runoff treated can be determined using [https://stormwater.pca.state.mn.us/index.php?title=TP_and_TSS_credits_and_guidance_for_manufactured_treatment_devices_(mtds)#Calculating_annual_volume_treated methods that are specified here].
| |
| − | #Each site plan must undergo review before approval of the unit for site installation.
| |
| − | #MWS-Linear Modular Wetland media shall conform to the specifications described in [https://stormwater.pca.state.mn.us/index.php?title=BioClean_MWS-Linear_Modular_Wetland#Links Specifications] and shall be sourced from Contech Environmental Services, Inc. (A Forterra Company) with no substitutions.
| |
| − | #Follow maintenance procedures given in the most recent version of the [https://www.conteches.com/linkclick.aspx?fileticket=J6ixCKc4ek0%3d&portalid=0 Operation and Maintenance Manual].
| |
| − | #Install the Contech MWS-Linear Modular Wetland in such a manner that flows exceeding the maximum Contech MWS-Linear Modular Wetland operating rate are conveyed around the Contech MWS-Linear Modular Wetland media and will not resuspend captured sediment.
| |
| − | #Discharges from the Contech MWS-Linear Modular Wetland units shall not cause or contribute to water quality standards violations in receiving waters.
| |
| − | #When applicable, adhere to use conditions provided in Washington State Department of Ecology's report (Ecology's Conditions of Use) [https://fortress.wa.gov/ecy/ezshare/wq/tape/use_designations/CONTECHmodularWETLANDSlinearGULD.pdf For Contech Engineered Solutions, LLC (Contech) Modular Wetlands Linear]. Note that some information in this report is specific to Washington State and not applicable to Minnesota.
| |
| − | | |
| − | ===Data analysis===
| |
| − | Credits apply only to the water being treated by a device. The applicable treatment volume must be determined using one of the [https://stormwater.pca.state.mn.us/index.php?title=TP_and_TSS_credits_and_guidance_for_manufactured_treatment_devices_(mtds)#Calculating_annual_volume_treated methods described here].
| |
| − | | |
| − | The Tier 1 credit equals the TAPE-approved credits. Tier 2 credit was determined by analyzing water quality data collected at the Lake Union Ship Canal Test Facility in Seattle, WA. The site consisted of 1.69 acres of impervious surface from parking and roadways areas. The unit size was 6 X 11 feet.
| |
| − | | |
| − | MPCA compiled data from General Use Level Designation Technical Evaluation Report. Below are summary statistics for the device.
| |
| − | *Median TP inflow - 0.103 mg/L
| |
| − | *Median TP removal (all data with concentrations > 0.05 mg/L) - 61.3%
| |
| − | *95% lower confidence limit TP removal (all data with concentrations > 0.05 mg/L) - 52.5%
| |
| − | *Median TP removal (data meeting TAPE criteria) - 63.3%
| |
| − | *95% lower confidence limit TP removal (data meeting TAPE criteria) - 54.0%
| |
| − | *Median TSS removal (all data) - 81.9%
| |
| − | *95% lower confidence limit TSS removal (all data) - 71.2%
| |
| − | TAPE means and medians represent values meeting TAPE criteria for TP (inflow concentrations of 0.1 to 0.5 mg/L) and TSS (inflow concentrations greater than 20 mg/L). Of the 24 samples, TAPE medians and means represent 16 samples for TP.
| |
| − | | |
| − | ===Inspection, operation, and maintenance===
| |
| − | Meet the conditions specified for [https://stormwater.pca.state.mn.us/index.php?title=BioClean_MWS-Linear_Modular_Wetland#TP_and_TSS_credits the appropriate TP and/or TSS credit].
| |
| − | | |
| − | Meet the following conditions, unless conditions for [https://stormwater.pca.state.mn.us/index.php?title=BioClean_MWS-Linear_Modular_Wetland#TP_and_TSS_credits the appropriate TP and/or TSS credit] are more stringent.
| |
| − | *2 maintenance visits required annually if annual precipitation exceeds 30 inches; one visit annually if annual precipitation is less than 30 inches
| |
| − | | |
| − | ==Links==
| |
| − | *[https://www.conteches.com/modular-wetlands Home page]
| |
| − | *[https://www.conteches.com/linkclick.aspx?fileticket=J6ixCKc4ek0%3d&portalid=0 Operation and Maintenance Manual]
| |
| − | *[https://www.conteches.com/Portals/0/Documents/Installation%20Guides/Modular-Wetland-Linear-Installation-Manual.pdf?ver=QU-ZIMq97p2sHlmZVxEU9g%3d%3d Installation manual]
| |
| − | *[https://www.conteches.com/knowledge-center/case-studies/search?filter=F7796HPVJ5 Case studies]
| |
| − | *[https://www.conteches.com/Portals/0/Documents/Brochures/Modular-Wetlands-Bro-new.pdf?ver=vRf0nHNQy1BAA_V6SUo1MA%3d%3d Brochure]
| |
| − | *[https://www.youtube.com/watch?v=1WyICe9eqBw&feature=youtu.be Video link]
| |
| − | *[https://www.conteches.com/technical-guides/search?filter=F7796HPVJ5 Contech technical downloads]
| |
| − | | |
| − | [[Category:Level 3 - Best management practices/Structural practices/Proprietary devices]]
| |
