Stormwater pollutant concentrations and event mean concentrations

This site is currently undergoing revision. For more information, open this link.
This page is in development and should be available by December, 2019

Stormwater pollutant concentrations and event mean concentrations

Because of the expense and difficulty of monitoring stormwater runoff, we often rely on existing monitoring information to estimate pollutant loading associated with runoff. Models or other tools are often used to predict pollutant loading. These models and tools require information on the pollutant concentration in runoff. For example, the Simple Method, which is commonly used to estimate pollutant loading, utilizes the following equation

\(L = 0.227 P P_j R_v C A\)

where

L = Load of a pollutant in pounds per year;

P = Rainfall depth per year (inches);

P_j = Fraction of rainfall events that produce runoff;

R_v = Runoff coefficient, which expresses the fraction of rainfall which is converted into runoff. Rv = 0.05 + 0.009(I);

I = Site imperviousness (i.e., I = 75 if site is 75% impervious);

C = Flow-weighted mean concentration of the pollutant in urban runoff (mg/l); and

A = Area of the development site (acres).

This page provides a discussion of pollutant concentrations in stormwater runoff, including a review of literature and recommended values to use

Determining the appropriate storm concentration

Pollutant concentrations in stormwater runoff are a function of the amount of pollutant available for transport in runoff and the nature of the runoff. The amount of pollutant available for runoff varies with land use (e,g, amount of pollutant available for transport), time between runoff events (e,g, build-up of pollutant), time within a runoff event (e.g. duration and intensity of runoff), the characteristics of the pollutant (e.g. soluble vs. less soluble), and other factors. This variability presents challenges in estimating pollutant loading because accounting for this variability is resource intensive.

We typically rely on "representative" values for pollutant concentrations. In the absence of specific monitoring data for a particular study or location, we most often use the event mean concentration (emc). The emc represents the expected concentration in typical runoff event. The remainder of this page focuses on emcs, but it is important to identify situations when using the emc is likely not appropriate.

• Estimating the loading from a specific runoff event, such as phosphorus concentrations in Fall runoff from residential areas. Emcs may be used if they represent runoff water quality for this time period (e.g. use of seasonal emcs).
• Assessing the impacts of runoff on receiving water receptors. For example, chloride concentrations in late winter runoff from areas receiving high inputs of deicer chemicals may exceed acute water quality standards by more than an order of magnitude. These excessive concentrations may adversely impact stream biota during this time period. Maximum concentrations should be used in situations like these.
• If the focus is on water quality of specific hydrologic events, such as low intensity or high intensity events.

Defining and use of event mean concentrations

One definition of event mean concentration (emc) is 'the average pollutant concentration for a given stormwater event, expressed in units of mass per volume (e.g., mg/L)'.

Although this seems conceptually simple, accurately estimating an emc for a given pollutant is challenging. Several factors affect emc, including the following.

• the method for calculating emc
• land use
• temporal variability (e.g. season)
• the pollutant and methods for sampling and analysis

These are briefly discussed below.

Despite challenges in accurately determining emcs, they are widely used in stormwater applications. Emcs are used in many stormwater water quality models and calculations of pollutant loading. They are therefore fundamental to understanding pollutant loads and how to address reducing pollutant loads in stormwater runoff.

Calculating emcs

Example of how emcs can be calculated using concentration and flow data taken at discrete time intervals. In the top example, assume all time intervals are 30. In the lower graph, intervals 1 and 2 from the top graph are combined and Q and C average, while the remaining intervals are left at 30. The emc for the top graph is 69.1 mg/L and 76.0 mg/L for the lower graph, even though the data are the same.

What is the first flush?
First flush is a phenomenon in which pollutant concentrations in stormwater runoff are greater in the early portion of a runoff event. First flush is common for relatively uniform land use settings, for winter and early spring runoff events, and for runoff events during fall leaf-drop. During dry periods between runoff events, pollutants build-up on impermeable surfaces. For Type 2 rain events, initial rain intensity is low and increases through a storm before decreasing near the end of the storm. The initial runoff is therefore highly concentrated with pollutants that have accumulated on impermeable surfaces. As runoff volume increases during an event and pollutants become more resistant to being washed off, concentrations decrease and typically reach steady state. First flush is not universally applicable to stormwater runoff, however. For example, if higher pollutant buildup on impermeable surfaces occurs in upper portions of a watershed, as might occur in an area with variable land uses, the peak concentration may be delayed as those higher pollutant loads take time to reach a receiving point. Similarly, some pollutants may be resistant to transport in early stages of an event. In other situations, concentrations in runoff may be uniform throughout an event, particularly if rainfall intensities are uniform and pollutants are soluble (e.g. chloride).
Schematic illustrating different runoff concentration profiles. Events 1 and 3 show delayed peak concentrations, Event 2 shows a strong first flush effect, and Event 4 a steady concentration profile. See text for discussion.

Emcs should represent the flow proportional concentration of a given pollutant parameter during storm events. The simplest way to calculate and emc is therefore to divide the total mass of a pollutant by the total runoff volume. Emcs can also be calculated as the sum, over multiple discrete time intervals within an event, of volume times the concentration for the time interval, divided by the total volume for the event

\( emc = (∫^t_0 C_tQ_td_t) / (∫^t_0 Q_td_t) ≅ (Σ C_tQ_tΔt) / (ΣQ_tΔt) \)

where C_t and Q_t are the concentration and flow volume over a discrete time interval d_t (Δt).

Erickson et al. provide detailed discussion and examples for calculating pollutant loading from stormwater runoff. The emc calculated for a specific event is a function of the sampling method. Erickson et al. discuss the following methods for sampling.

• Flow-weighted discrete samples: "When samples are collected based on a user-specified constant incremental volume of discharge (e.g., every 1000, 2000, or 5000 gallons) that passes the sampler, the samples are defined as flow-weighted. Each flow-weighted sample is assumed to represent the average pollutant concentration for the entire incremental volume of water to which it corresponds. Each discrete sample is stored in an individual container, and the contents of each container are analyzed separately."
• Flow-weighted composite samples: "Flow-weighted composite samples are collected every time a user-specified constant volume of flow passes the sampler and all samples are stored in a single container. To determine pollutant concentration, an aliquot is collected from the composite sample, and the concentration is assumed to represent that of the entire composite sample."
• Time-weighted discrete samples: "Time-weighted discrete samples are collected at a user-specified, constant time interval (e.g., 30 minutes), and each sample is stored in a separate container and analyzed separately. Because the magnitude of the discharge during a natural storm event varies over time, each time-weighted sample does not represent a constant volume of discharge."
• Time-weighted composite samples: "Time-weighted composite samples are collected at equal time increments, and all samples are stored in a single container. ... Time-weighted composite sampling is not recommended."
• Discrete grab samples: "A grab sample is a single sample collected at one location over a relatively short time period, typically sampling the entire cross-section of water. Discharge must be accurately and continuously measured and the time of each grab sample must be recorded to assess pollutant removal performance. Discrete samples are stored in individual containers, and the contents of each container are analyzed separately."
• Composite grab samples: "Composite grab samples are typically collected at variable time and volume increments and stored in a single sample storage container. Composite grab sampling is not recommended."

The sampling method affects the resulting calculation of emc. For example, in the adjacent image, emcs were calculated for the same runoff event. In the top portion of the image, sampling occurred every 30 minutes and the overall emc is 69.1 mg/L. In the lower portion of the image, the first two time intrvals were combined and Q and C averaged over the 60 minute time interval, while the remaining time intervals were 30 minutes each. The overall emc is 76.0 mg/L. The difference is a result of a bias toward higher concentrations in the early portion of the runoff event for the lower graph. This tendency toward higher pollutant concentrations in the early part of a runoff event is called the first flush.

Factors affecting emcs

As discussed above sampling method affects the emc, particularly when concentrations and/or runoff volumes are not relatively constant throughout a runoff event. Additional factors affecting emc include the following and are discussed in greater detail below.

• Land use
• Season
• Pollutant
• Rainfall volume and intensity
• Antecedent pollutant concentrations
• Watershed characteristics

Effects of land use

Some generalizations about pollutant loading as a function of land use include the following.

• Commercial, industrial, and transportation land use typically have higher percentages of impervious and directly connected impervious surface, as shown in the accompanying table summarizing curve numbers for different land uses. This results in more efficient delivery of pollutants and runoff compared to other land uses. Consequently, we expect higher emcs from these land uses for smaller runoff events and when pollutant buildup on impermeable surfaces is greater, and lower emcs for larger runoff events when dilution occurs.
• Nutrient (phosphorus, nitrogen) concentrations are greater in residential areas and other land uses that contribute significant amounts of organic material to impermeable surfaces. Dissolved fractions also comprise a greater percent of the total load for these pollutants.
• Concentrations of metals increase as road density and traffic volume increase.
• Concentrations of petroleum-related compounds and polycyclic aromatic hydrocarbons (PAHs) increase as road density and traffic volume increase.
• Concentrations of total suspended solids (TSS) may be similar across different land uses, but the characteristics of the TSS varies. Organic fractions make up a larger percent of TSS in residential areas and other land uses where there are sources of organic material to impermeable surfaces.
• Bacteria concentrations are typically greater in residential areas due to greater inputs from domestic animals (e.g. dogs), birds, and other animals. Studies also suggest irrigated lawns and leaves/organic material on impermeable surfaces contribute to bacteria loads.
• In cold climates where deicers are applied, chloride concentrations are a function of deicer application rates. Chloride concentrations are therefore highly variable in areas where deicers are applied.
• Oxygen demand
• Concentrations of several organic chemicals, such as pesticides and chlorinated compounds, varies. Factors affecting concentrations include industrial sources, presence of contaminated sites, and historic use of these materials, and atmospheric deposition.
• Although the potential for nutrient and bacteria loads is greater in lower density residential areas, the lower amount of directly connected impervious surface typically results in lower emcs for lower density residential land use.
• Pollutant concentrations in open, forested, and park areas are lower, primarily due to reduced impervious surface.

Because of the variability in emcs across different land uses, it is beneficial to consider different land uses when calculating pollutant loads. Compositing emcs across land uses is generally not recommended.

Curve numbers for antecedent moisture condition II (Source USDA-NRCS).
Link to this table

Land use description	Hydrologic soil group
	A	B	C	D
Meadow - good condition	30	58	72	78
Forest
Poor	45	66	77	83
Fair	36	60	73	79
Good	30	55	70	77
Open space
Poor	68	79	86	89
Fair	49	69	79	84
Good	39	61	74	80
Commercial 85% impervious	89	92	94	95
Industrial 72% impervious	81	88	91	93
Residential
1/8 acre lots (65% impervious)	77	85	90	92
1/4 acre lots (38% impervious)	61	75	83	87
1/2 acre lots (25% impervious)	54	70	80	85
1 acre lots (20% impervious)	51	68	79	84
Impervious areas	98	98	98	98
Roads (including right of way)
Paved	83	89	92	93
Gravel	76	85	89	91
Dirt	72	82	87	89
Row crops
Straight row - good	67	78	85	89
Contoured row - good	65	75	82	86
Pasture - good	39	61	74	80
Open water	99	99	99	99

Recommended event mean concentration (emc) values

As a result of our literature review we developed recommended emc values. These are summarized in the following table.

For phosphorus and total suspended solids, we developed a broader discussion of emcs. We suggest you read these sections if using emcs for your stormwater applications.

Phosphorus emcs

Data from the following studies was used to generate emcs for total phosphorus.

• National Stormwater Quality Database. This dataset provides data from several nationwide studies. We used only data from region 1, which includes Minnesota and states with similar rainfall patterns. Data were compiled for four land uses: Commercial (n=165), industrial (n=84), residential, (n=249), and open space (n=6).
• Lin (Review of Published Export Coefficient and Event Mean Concentration (EMCs) Data. This report includes summaries of multiple studies conducted in North America. Data existed for all land uses included in the table presenting recommended emcs.
• Washington District Department of the Environment - Selection of Event Mean Concentrations (EMCs). This study summarized data from studies in the Washington D.C. area. Land uses included commercial, roadway/highway, industrial, forest/open, and residential.
• U.S. Environmental Protection Agency, 1983, Results of the Nationwide Urban Runoff Program—Executive summary. Land uses included commercial and residential.
• Urban Stormwater Quality, Event-Mean Concentrations, and Estimates of Stormwater Pollutant Loads, Dallas-Fort Worth Area, Texas, 1992–93. Included commercial (n=42), residential (n=77), industrial (n=63) land uses.
• A review of sediment and nutrient concentration data from Australia for use in catchment water quality models . A compilation of multiple studies from Australia. Included forest (n=68) and mixed (n=36) land uses.
• Characterization of Urban Runoff Pollution between Dissolved and Particulate Phases . Study of five sites in China. Land uses included roof and transportation (roads).
• Quality Of Wisconsin Stormwater, 1989-94. Samples from mixed land use in Wisconsin (n=204).
• Analysis of Nonpoint Source Pollution Runoff from Urban Land Uses in South Korea. 23 samples in Korea from high density residential, medium desntiy residential, industrial, institutional land uses.
• Seasonal Performance Variations for Storm-Water Management Systems in Cold Climate Conditions. 15 samples from transportation land use in New Hampshire.
• Determination of event mean concentrations and first flush criteria in urban runoff. 31 samples from transportation land use in Los Angeles.
• Multiple linear regression models of urban runoff pollutant load and event mean concentration considering rainfall variables. 45 samples from commercial, industrial, and high density land uses.
• Stormwater runoff driven phosphorus transport in an urban residential catchment: Implications for protecting water quality in urban watersheds. 29 events from low density land use in Florida.
• Sources of phosphorus and street dirt from Two Urban Residential Basins in Madison, Wisconsin, 1994-95. 25 samples from medium density land use in Wisconsin.
• Nutrient Sources in Urban Areas – A Literature Review. Report summarizing multiple studies in Colorado. Land uses include residential, mixed, commercial, and open space.
• Contribution of surface runoff from forested areas to the chemistry of a through-flow lake. Forested land use in Poland.

The following table summarizes results from our literature review. The table includes a range of values observed in the literature. Note this range does not represent a statistically-derived range but instead is based on a combination of data analysis and best professional judgement. For example, we did analyze the data for outliers, but also omitted entire studies if we felt the data were not representative of typical conditions likely to be encountered in Minnesota. To see the full range of values compiled from the literature, open the Excel spreadsheet containing the data.

Event mean concentrations for total phosphorus.
Link to this table

Land cover/land use	Range (mg/L)	Recommended value (mg/L)	Notes
Commercial	0.20 - 0.34	0.200	If applicable to models being used, adjust curve numbers/runoff coefficients when calculating loads
Industrial	0.23 - 0.55	0.235	If applicable to models being used, adjust curve numbers/runoff coefficients when calculating loads Adjust upward if specific phosphorus sources exist
Residential	0.26 - 0.38	0.325	Concentrations vary widely depending on local conditions
High-density/Multi-family residential	0.28 - 0.40	Calculate1	Insufficient information to recommend a specific emc Concentrations vary widely depending on local conditions
Medium density residential	0.18 - 0.40	Calculate1	Insufficient information to recommend a specific emc Concentrations vary widely depending on local conditions
Low density residential	0.24 - 0.40	Calculate1	Insufficient information to recommend a specific emc Concentrations vary widely depending on local conditions
Freeways/transportation	0.25 - 0.45	0.280	Concentrations vary widely depending on inputs Adjust upward for areas receiving large inputs of road salt or sediment or having very heavy traffic loads Adjust downward for low traffic areas or areas with reduced inputs (e.g. little road salt application, limited truck traffic)
Mixed	0.16 - 0.84	0.290	Residential land use was the primary land use in most studies that cited values for mixed land use If the study area can be delineated into specific land uses and impervious area for each land use is know, we recommend calculating the emc
Parks and recreation		Use value for open space or calculate	emc will be a function of vegetative cover Adjust upward if street tree canopy cover is high or pervious areas are primarily grass on compacted soils
Open space	0.12 - 0.31	0.190
Conventional roof	0.01 - 0.20	0.030
Institutional	0.14 - 0.422	See note	Use low values in range (0.200 mg/L or less) for facilities such as campuses, where there is considerable pervious area Use high values in range (0.30 mg/L or greater) for areas with considerable impervious surface, such as sports facilities or facilities with large parking areas
Forest/shrub/grassland	0.03 - 0.45	0.090	Concentrations are likely to vary with season in areas with fall leaf drop
Open water and wetlands		see Notes (next column)	If data exist, use the phosphorus concentration for the water body of interest If data for a specific lake do not exist, use data from similar lakes in the area emcs for wetlands will typically be higher than for lakes in an area. Consider using a value equal to 2 times the value for lakes in an area.
Cropland (row crops)	0.126-1.348	2	Median from our review = 0.533
Pasture	0.35-0.45	2

¹The link takes you to information on calculating event mean concentrations for areas with multiple land uses.
²Our literature review was not extensive enough to warrant a specific recommend emc for this land use

Dissolved and particulate phosphorus

In many places in this manual and in the MIDS calculator, we assume that particulate phosphorus accounts for 55 percent of total phosphorus and dissolved phosphorus for 45 percent of total phosphorus.

Data on event mean concentrations

Below are data we've compiled during our literature review.

• National Stormwater Quality Database. The National Stormwater Quality Database (NSQD) is an urban stormwater runoff characterization database developed under the direction of Dr. Robert Pitt, P.E., of the University of Alabama and the Center for Watershed Protection under support from the U.S. Environmental Protection Agency.