Winter Parking Lot and Sidewalk Maintenance Manual Revision as of 20:48, 2 February 2016 by PLeegar (talk | contribs) (→Calculating Parking Lot or Sidewalk Area)
Contents
Background Information
Good Business Choices
Customer service is the key to success. Best Management Practices (BMP) keep parking lots and sidewalks safe and also reduce environmental impacts. Educating customers on the proper methods of snow removal and ice control (and of the value of this approach) can create a good and long-standing relationship.
Customers want reliable service. Providing a well-planned and well-executed winter maintenance program will have a positive impact. Using the latest technologies will increase the abilty to provide reliable service.
Customers want to hire educated winter maintenance professionals. This maunal will provide the necessary information to increase staff knowledge on the best practices for winter maintenance.
Using the right amount of material at the right time, will save time and money.
Certification in Smart Salting is a good reflection on the professional and the organization.
Customers and the public want safe parking lots and sidewalks. Understanding the materials, weather and application rates, provide a head start on controlling icy, slippery parking lots, and sidewalks.
Clean and neat parking lots and sidewalks are important to the public. By using less material and increased winter sweeping, pedestrians will track less material into buildings and there will be less damage to flooring. Proper snow storage makes debris removal in the spring easier. Covered storage of deicers will reduce loss of material, protect water, and is more aesthetic. Using BMPs and lower application rates will keep parking lots and sidewalks looking neat.
Customers also want affordable snow and ice control. The use of sophisticated chemicals and equipment may require a larger budget up-front; however, these costs can be balanced by reduced on-going costs. Reducing the need for sweeping, floor and rug maintenance, parking lot striping, and snow and ice maintenance time will allow for cost savings.
Minnesotan’s value water resources and the protection of lakes, streams, and wetlands is important. Educating customers how sustainable winter maintenance protects water resources is necessary.
Using less material is an effective approach to protecting our water resources. It is difficult to recover salt or sand once applied.
Water and Environmental Impacts
- Only 2.5% of all of the water on this planet is freshwater (not saltwater). Of that, less than 1% is available for use. The majority of the freshwater is frozen in the glaciers (Freshwater Crisis n.d.).
- Water is recycled over long periods of time. There is a limited supply of water on this planet. Water is reused, recycled and dispersed as illustrated below from the Minnesota Department of Natural Resources (DNR), “Healthy Rivers: a Water Course” (Healthy Rivers 2004).
Chloride concentrations are increasing in many surface waters and groundwater across Minnesota.
- In the Twin Cities Metropolitan Area (TCMA), of surface water bodies tested, 39 are on the draft 2014 impaired waters list for chloride exceedances and 38 more are found to be at high risk as of July 2015. (MPCA 2015). Salts (chloride) dissolve in water and move with the water to nearby lakes, streams, and wetlands and also infiltrate into groundwater.
- Chloride is virtually a permanent pollutant that does not degrade and cannot be removed from surface waters. Once in the water, it continues to accumulate in the environment over time.
- Salt water is heavier than freshwater and may sink to the bottom of lakes. This may cause chemical stratification of the lake and loss of or changes in lake turn over (Stefan et al. 2008).
- Thirty percent of the 270 shallow aquifer monitoring wells tested in the TCMA exceeded the state chloride standard. (MPCA 2013).
- About 75% of Minnesotans rely on groundwater for drinking water. The MPCA has found 30% of the shallow monitoring wells, often found in urban areas, have exceeded the state standard for salt levels. As water moves from shallow to deeper aquifers, the salt contamination could penetrate sources of drinking water (MPCA 2013).
- The average salt use in the TCMA based on purchasing records is 349,000 tons per year (Sander et al. 2007).
Deicers can be very damaging to both soil and vegetation. Efforts to keep salt off vegetation are needed: drive slower when applying deicers, turn down spinner speed to reduce spread pattern, use drop spreaders on sidewalks, store snow piles on hard surfaces, and reduce application rates. One source of information about salt-tolerant plants is the Plant Selector from Minnesota Department of Transportation.
Impacts of Materials
Abrasives and deicers cause problems to infrastructure, drainage, water, vegetation, and soils when used in large quantities. Abrasives: Winter Sand
- Runs off parking lots with water to the nearest storm drain entering lakes, wetlands, streams, and rivers.
- Fills in surface water bodies, accelerating the aging process.
- Covers habitat and disrupts the food chain.
- Irritates the gills of fish.
- Clogs and disrupts the flow of water in storm drain systems.
Deicers are not "environmentally safe" regardless of what the bag says.
Chlorides commonly used for deicing are Sodium Chloride (road salt), Magnesium Chloride, Calcium Chloride, and Potassium Chloride.
- Road salt is the least expensive and most widely used deicer.
- Salt is corrosive to steel.
- Some have corrosion inhibitors and anti-caking agents added that are often toxic.
- Frequently damage plants through contact or by interfering with soil properties.
- Salt can cause soil to lose its ability to retain water, leading to soil erosion.
- Excess salt can make soil more alkaline and compact, and less permeable, making it more difficult to store nutrients that plants need to grow.
- Cannot be removed by stormwater ponds or rain gardens.
- Cannot be removed from the lakes, wetlands and rivers.
- Are persistent pollutants and will not break down over time.
About one teaspoon of salt can pollute five gallons of water. This applies to all chloride containing deicers.
Acetates:
- Are non-chloride compounds.
- Are an organic substance.
- When added to water, compete with aquatic life for oxygen.
- Contribute nutrients which promote algal blooms in lakes and ponds.
- Most of the problems they cause in the water are relatively short term, but severe.
- Are usually safer for vegetation.
- Are less corrosive than salts.
- Have the potential to be treated by stormwater BMPs.
Acetates can have a high biological oxygen demand (BOD), and can contribute to oxygen depletion in soil and water. Use carefully.
Plant-based additives (beet, corn, molasses):
- These additives do not contribute chloride to water but contribute nutrients (fertilizer).
- Cause an increase aquatic plant and algae growth.
- Use up oxygen in the lake or water body as they decompose.
- Serious impacts but not as long-lasting as chloride.
One lb. of phosphorus encourages growth of up to 500 lbs. of algae. Phosphorus is in plant-based products.
Twin Cities Metropolitan Area Chloride (TCMA) Management Plan
There are two primary sources of chloride to Minnesota water resources: 1) salt applied to roads, parking lots, and sidewalks for deicing; and 2) water softener brine discharges to municipal wastewater treatment plants (MPCA 2015). To address chloride impacts to Minnesota water resources, the MPCA worked with local stakeholders to develop a Chloride Manageme6nt Plan designed specifically to minimize chloride use across the seven counties of the metropolitan area. This plan is intended to be useful for all winter maintenance practices. The plan can be located on the MPCA’s website: http://www.pca.state.mn.us/programs/roadsalt.html
1 ton of rock salt ($50) causes greater than $1,450 in corrosion damage to bridges. (Sohanghpurwala 2008)
Fathead Minnows will die if exposed to chloride concentrations of 443 mg/l for more than 30 days (Axler n.d.)
Prepare for Winter Operations
Policies/Plans
Start now—develop a maintenance policy or plan that guides winter operations. A little planning and communication up-front can help achieve better results throughout the season.
- Develop a maintenance policy or plan.
- Review the maintenance policy with the crew.
- Inform customers of the maintenance policy.
- In the plan:
- list the key actions to take during a winter event
- list the order of these actions
- address the level of service
- consider customer expectations, the hours and use of the building, priority access points and environmental concerns in the policy
- spell out any additional strategies such as routes, chemicals, application rate ranges etc.
- Follow the plan.
- Document actions.
- Review and update the maintenance policy each year.
Our waters are threatened by contracts which are based on fees for material use. This encourages overuse of materials.
Reduce liability. Establish a maintenance policy and follow it.
Training
Reduce risk by having a solid written winter maintenance policy and training program that utilizes best management practices. Schedule training for supervisors, staff, and customers.
The MPCA has three Smart Salting training classes available:
- Level 1 Winter maintenance of roads
- Level 1 Winter maintenance of parking lots/sidewalks
- Level 2 winter maintenance training for supervisory staff
Check the MPCA website to find out about upcoming training opportunities.
Storage
Snow Piles:
- Store in an area where the solids can be recovered after the snow melts.
- Locate snow piles down-slope from salt and sand storage to prevent snow melt from flowing through salt or sand storage areas.
- Avoid pushing snow into lakes, ponds, wetlands, rivers, or other natural areas.
Improper storage of salts can lead to groundwater cantamination
Salt and Salt/Sand Piles:
- Storage areas often cause groundwater or surface water contamination. These problems can be easily tracked back to the source. Do not skimp on proper storage. When locating new storage for liquid or granular products investigate local visual screening ordinances.
- Indoor storage is recommended.
- Store on an impervious (water proof) surface.
- Floor should be sloped away from the door.
- Sweep loading areas back into the pile.
- Store away from lakes, rivers, ditches, storm drains, and wetland edges.
Salt storage areas are often a source of groundwater contamination. To reduce risk, have a covered storage area on an impervious pad. Take measures to keep salt or salt brine from leaving storage area.
A common mistake is storing a salt pile downhill from a snow pile
Salt Bags:
- Protect from rain or snow.
- Dispose of bags properly.
- Seal all open bags.
Liquids:
- Know the freezing point of the liquid. This will determine if it can be stored outdoors. Salt brine (NaCl) will freeze at -6o F.
- Tanks should be double-walled or have secondary containment. Secondary containment is like creating a bath tub around the tank so if the tank leaks, the “tub” captures the spill.
- Label the tank documenting its contents.
- For more information on storage tanks see www.pca.state.mn.us/cleanup/ast.html
Sand piles:
- Winter sand is typically mixed with some deicer to prevent freeze-up of the pile; therefore, sand pile storage should be the same as salt pile storage.
- Store leftover winter sand for next year. Do not use it for other purposes.
Prevent groundwater contamination. Do not locate storage areas near wells. Limestone regions with fissures and sinkholes are very prone to groundwater contamination, as are those with sandy soils.
Weather =
Know existing and potential weather conditions for a successful snow and ice control operation. Monitor the weather closely to prepare to act early in storm situations. Check the National Weather Service http://www.noaa.gov, local TV stations, or website weather. A Road Weather Information System (RWIS) is available for [http://www.rwis.dot.state.mn.us/ free on-line} at. The RWIS provides real time pavement temperatures and other information from locations around the state.
Pavement Temperature
Pavement and air temperature are different. Know the pavement temperature to determine the proper amount and type of material to apply. Weather stations report air temperature which is measured at least 6 ft. in the air. The air temperature is not helpful when trying to determine what to apply to surfaces on the ground.
Air temperature measurements are generally the same in a given area, but pavement temperatures in the same general location can vary greatly. Pavement temperatures are influenced by exposure to sun, pavement type, and subsurface materials.
The same air temperature in November and January will often accompany very different pavement temperatures.
The hand-held temperature sensors can be purchased from auto part stores for less than $100. Some temperature sensors only accurately monitor in the warm temperature range, confirm the one purchased measures in the cold temperature range. Mirror-mounted temperature sensors are also available; they are less likely to be lost or stolen, but do cost more and are generally not available at an auto parts store. RoadWatch by Commercial Vehicle Group, Inc. is one example of this type of sensor. A small investment in equipment will improve performance.
Knowing the pavement temperature allows the application of the proper amount of material for each situation.
Getting prepared for winter
- Calculate the area of the parking lots, service roads, and sidewalks.
- Understand the environmental problems caused by snow, salt, and sand storage. Determine where and how to best store each item.
- Understand the properties of various deicers, and then select the type(s) to use.
- Train the crew on proper application rates.
- Mark islands, fire hydrants, and other landmarks that could be obscured by snow.
- Note existing conditions of curbs and other items that might be damaged by winter maintenance activities.
- Note or mark all catch basins, manholes, sidewalk segments that may cause a hazard to the plow and the operator.
Drainage
Inspect storm drains in the fall. Remove obstructions such as leaves, sticks, and trash to prepare for the spring melt. Because storm drains lead to lakes, rivers, ponds, and wetlands, never use salt to open frozen storm drains. Salt used to thaw frozen drains harms aquatic life. Use non-chemical methods such as heat to open drains.
Poor drainage on the maintenance surfaces will result in icy surfaces and will increase the risk of safety problems. These areas cause the application of salt on non-snow event days in the winter. To remedy this, inventory the site and note drainage problems. Make a checklist so the professional or client can fix these drainage problems in the summer.
Examples of drainage problems:
- Roof that drips on the steps
- Downspout discharging on sidewalk
- Sidewalk segments sloped into a V
- Potholes or low spots in parking lots
Storm drains lead to the nearest lake, river, pond, or wetland. They do not go to a treatment plant.
Equipment
The trend in winter maintenance is to use less material to accomplish the same results. Following this trend will reduce environmental impacts and save money. Below are listed a few tips, but there are many other innovations in the equipment area that can help to reduce application rates.
- Purchase a pavement sensor (Figure 8)
- Buy equipment that can deliver very low rates of granular products.
- Outfit larger trucks with ground speed controls so that the application rate changes automatically as the speed changes.
- Modify existing equipment so that it can discharge the application rates described in the “Application Rates” section. Older equipment often applies more salt than recommended.
- Outfit sidewalk spreaders with shields to better direct the spread pattern.
- Invest in equipment that can deliver liquid deicers.
- Obtain a tank for liquid storage or find a near-by source of liquids to fill up trucks.
Calibration
Calibration is an essential procedure to understand how much material will be discharged at a given setting. No matter how sophisticated or simple the operation, calibrate each piece of equipment in the fall of the year.
Calibration tells how much material will be applied at each setting.
Simple Calibration for Salt Spreaders=
If the equipment has different settings, it must be calibrated for each setting and for each product, as they all flow differently. It generally takes a team of two or three people to calibrate equipment efficiently.
Ground Speed Controlled Spreaders
Ground speed controlled spreaders are run by a computer in the cab and are tied to the speedometer and an auger or conveyor sensor in the rear of the truck. The application rate is set and the computer regulates the amount of salt discharged (regardless of the speed traveled) consistently. Most equipment used for winter maintenance of roads have ground speed controls. These are more effective and efficient systems than the manually controlled systems.
The equipment vendor will have specific calibration instructions for the operation based the type and brand of equipment. Contact them; it is in their best interest to provide instructions to calibrate and correct product use. This is the basic principle behind calibrating a ground speed controlled spreader:
- The speedometer input (sensor) lets the controller know how fast or slow the truck is traveling.
- The auger or conveyor input (sensor) tells the controller how fast or slow the auger is turning.
- To calibrate a ground oriented controller, input the pounds discharged per revolution.
- Once the computer knows the pounds/ revolution, it will calculate the necessary auger speed needed to hit the target application rates at the speed the truck is traveling.
Best bet: Contact manufacturer for calibration instructions.
Calibration allows accurate deicer use
Manual Controlled Spreaders
Manual controlled spreaders fall into two categories. Those that have an auger or conveyor and those that are gravity fed. They operate by selecting a setting that changes the size of the discharge opening and/or the auger or conveyor speed. More or less salt may be discharged depending on the speed of application. Most parking lot and sidewalk spreaders fit into one of these two categories.
All good programs are based on calibration of equipment.
The basic principle behind calibrating an auger/conveyor spreader is to choose a setting, run the spreader for a timed interval, and weigh the discharge. Record the discharge and repeat for all settings. In the end, there will be data that tells the operator how much material will be delivered at each setting. With this information, the operator can choose the proper setting. Without this information, they have no guidance on which setting to use. Calibration is different for gravity fed spreaders. There is more detail on this in a few pages.
Apply wisely. The chemicals applied cannot be recovered.
Surfaces such as pervious asphalt, pervious concrete, and pervious pavers do not experience refreeze. All melted snow and ice travel to the storage layer below the surface. Salt is generally not needed on these surfaces and sand should be avoided.
Example: Step #1, blank calibration form
See the References and Resources section for a full size form to copy for calibration. This is how the empty form looks.(Keep a stack of these on a clipboard when ready to begin the calibration.)
Example: Step #2, calibration form filled out during calibration
Fill in the header information and column 2, the discharge weight per setting.
Example: Step #3, calibration form ready to put in truck for road application'
Back in the shop, do the calculations to fill in the rest of the blanks. Multiply the weight in column 2 with the multiplier in the top row. This provides the pounds per mile that needed to fill in the table.
Some fish species are affected by concentrations of less than 1000 ppm NaCl, about 1 to 1.5 tablespoons of salt in 5 gallons of water.
Example: Step #4, calibration form ready to zip tie to hand spreader or put in truck for parking lot application.
Divide by 63 to convert pounds per lane mile to pounds per 1,000 square feet. This is very useful for parking lot and sidewalk applications.
Gravity Flow Equipment
This is applicable for equipment that does not have a motorized delivery system such as an auger. This type of equipment might be a pickup mounted spreader, gator mounted spreader or a hand push spreader. Gravity flow equipment is typically controlled by gate opening and speed of application.
Step 1: Calculate discharge rate
- Mark out a 10-foot stretch of pavement. (By increasing the size of the test area i.e., the longer the test area, the more accurate the results will be).
- Sweep it clean of sand or any other material.
- Using a constant speed, apply one pass of material to the test area.
- Measure the width the material is spread or bounces, in feet.
- Sweep up and weigh the material that is within the marked 10-foot stretch.
- Record the lever position/setting for the gate/chute. If there are no numbers for the positions, make permanent marks on the equipment to identify the positions.
- To improve accuracy, repeat this two more times and calculate the average weight of material applied.
- Record results in columns A, B, C, and D (Figure 14).
Step 2: Repeat step #1 for various settings.
Step 3: Fill out chart.
- Fill out columns E, F, and G (Figure 14).
- If using more than one type of material, repeat the test for each material.
- Place the completed calibration chart with the equipment.
Shortcuts:
- Put down a tarp over the application area; this makes it quicker to recover and weigh material.
- After the first pass, put a bag around spreader to catch discharge material. The first pass is needed to determine the spread width.
Calculate application rate:
What if calibration is not a practice?
Even without calibrating the equipment, the amount of material to use can be determined but will take more time to calculate. Know the material, the size of the area to be treated, and the pavement temperature, then consult the application rate chart (application rate section) and do the math. Without calibration, the way to evenly distribute the recommended amount across the maintenance area must be determined by the professional. This approach may work well for treating sidewalks using the “chicken feed” method. For example:
- 20oF degrees pavement temperature and rising
- Using dry salt
- Sidewalk is 2,000 square feet
- Table recommends 2.25 lbs. per 1,000 square feet (for this situation)
- Measure about 4.5 lbs. of salt
- Figure out a way to spread it evenly over the 2,000 sq. ft. surface
Sand fills in lake bottoms, accelerating the aging process of lakes. Lakes get shallower as they age, some eventually becoming wetlands.
Materials
All products have pros and cons. No one material is suitable for every condition. It is best to have a variety to choose from to select the one that works the best, with the least amount applied, in a specific situation. Understand the melting properties of the deicers; do not use the product without understanding how it works.
The best way to reduce impacts, save money and maintain customer satisfaction is to:
- Know what is in the product.
- Know the product’s practical melting range.
- Use it only when it will be effective.
- Use the minimum amount needed to get the job done.
- Seek out products that allow for smaller application rates.
Abrasives:
- Sand is an abrasive; it does not melt snow and ice.
- Abrasives provide traction on top of packed snow or ice.
- Abrasives and deicers typically work better alone, rather than together.
- A small amount of salt must be mixed in the sand to keep it from freezing in the pile (less than 10%).
====Salts====:
- Sodium Chloride, Magnesium Chloride, Potassium Chloride and Calcium Chloride are all considered “salts.”
- Salt is a deicer; it will melt snow and ice.
- Salt lowers the freezing point of water from 32° F to a colder temperature.
- Salt must be dissolved to work; therefore, liquids act faster than solids.
- Salts have different melting characteristics, depending on the selection.
- Road salt (NaCl) is a granular product and is mined from the earth.
- Magnesium Chloride (MgCl2) and Calcium Chloride (CaCl2) can naturally occur as liquids.
- MgCl2 and CaCl2 are hygroscopic, drawing moisture from the air to the pavement.
- Salt brine (NaCl) is commonly used at a 23.3% concentration as this has the lowest freezing point and can be stored and handled down to -6°F.
Acetates:
- Acetates are chemically manufactured, not mined from the earth.
- Acetates are more expensive than chloride salts.
- Acetates are less corrosive than salts.
- They have a wide melting range, depending on the selection.
- They are not better or worse than chloride salts, they are different.
Plant-based additives
Corn, beet, molasses, or other organic additives are added to salt or salt brine to change its performance, though how they function as an ice melting agent is not well understood. Clear Roads (2015), a national resource consortium of state agencies, is studying this issue.
- Often have very low ice melt capacity.
- May be used to reduce corrosion.
- Are sticky and may help dry material stay on the surface longer.
Speed of Melting
Will the road salt used have time to work or is it better to switch to a different deicer? This chart will aid in making that decision.
Do not use dry road salt below 15º F. This wastes money and time.
Practical Melting Temperature
Use care when reading the melting temperature on bags of deicers. The package often lists the eutectic temperature, which is the lowest possible melting temperature. At this temperature, it would take a very long time to melt ice. Instead, use the lowest practical melting temperatures in the chart below or ask the supplier for the practical melting temperature and the time it takes to melt ice at that temperature. It should be noted that there is not a standard measure for determining the lowest practical melting temperature. Across the literature there are a range of values. In the References and Resources section there are lists of several websites to learn more about the lowest practical melting temperature.
Testing
When ordering a liquid product in bulk, test it. If it is NaCl brine it should be 23.3%. If it is another liquid, use the vendor recommended density and test to confirm. Hydrometers are the tools for testing the density of liquids. They are inexpensive and look similar to a thermometer. Research the product, understand the practical melting temperature, and know the list of ingredients. Take time to test the materials to ensure that they perform as expected. Product labeling can be confusing; some list the eutectic temperature while others list the lowest practical melting temperature.
The list of ingredients may or may not be included. Often, the percentage of each ingredient is not included. Do not rely solely on the bag or on the manufacturer’s literature. There are no labeling requirements; manufacturers can choose to label products in their own way.
Cost and Availability
Of the deicers, NaCl is typically the cheapest and easiest to find. Because of this, it is widely used and overused. Sodium chloride is only effective at pavement temperatures above 15oF. Because it doesn’t work well at colder temperatures, it is often over-applied in attempts to increase its effectiveness. At temperatures lower than 15oF degrees, switch to a different deicer.
Non-chloride deicers are more difficult to find and often cost more. Take the time to source and try non-chloride products if there are concerns from the professionals or customers about the long-term effects of chlorides on the lakes and rivers. All deicers have environmental impacts but the impacts of chlorides are very long-term.
Salt and sand mixes are commonly used to stretch the salt budget. This is an ineffective practice. Salt and sand work against each other. To save money, use deicers when melting is needed and sand for temporary traction to buy time at temperatures too low for deicers to be effective. Pre-wetted sand has shown to be effective in keeping sand in place longer on icy surfaces.
Using 50/50 salt/sand mix is generally half right or half wrong. Using a salt/sand mix leads to over application of both materials.
Sidewalk Tips
Always remove snow prior to applying deicers. Plow, blow, or sweep first; the chances of refreeze diminish and slush build-up is minimized.
- Sidewalks are the most over-salted areas in winter maintenance.
- Use drop spreaders, not rotary spreaders. If using a rotary spreader, install shields to restrict the spread pattern. This minimizes the application rate and protects the vegetation.
- Many slip and fall incidents occur within 10 ft. of the curb lines. Adjust practices to include proactive measures like anti-icing.
- If the professional is not responsible for sidewalk maintenance, consider providing this information to the responsible party.
- Focus on aggressive mechanical removal of snow. The less snow, the less deicer required. This will lend itself to a safer surface.
- Deicers can harm heated sidewalks.
- Abrasives can harm permeable pavers or permeable concrete.
Salt only needs to melt 1/16 inch to prevent the bond between the pavement and the ice. Save money by applying salt before the ice bonds to the surface it doesn’t need to melt through the ice.
Building Entrances
Steps are often the most over-salted area in all of winter maintenance. This overabundance of deicer causes damage to floors inside the building as salt and/or sand is tracked in. It causes problems outside of the building with deterioration of concrete and metal structures. Over applying deicer costs more money than necessary, pollutes the water, and does not provide any additional safety. The right amount of deicer and proper mechanical removal of snow and ice will yield better results.
A free short video for small site winter maintenance is available. It is designed for those that do winter maintenance of small sites such as stairs, curb cuts, and handicap ramps. The video is a visual instruction tool useful for those who apply granular deicer to small areas outside building entrances. It recommends:
- Do site assessments, document drainage problems, and fix them in the summer (e.g., roof that drips on steps, downspout that drains to sidewalk).
- Always remove snow prior to applying deicers. The less snow, the less deicer required for a safer walking surface.
- Use the proper tool for snow and ice removal:
- Push shovel (no sides) for pushing snow.
- Scoop shovel (sides) for lifting snow.
- Broom or blower for light fluffy snow.
- Ice scraper for use under ice and compaction.
- Ice chisel for breaking open compaction, or under ice and compaction.
- Use hand-held spreaders to disperse deicers. Spreaders:
- Provide more even distribution.
- Reduce amount needed.
- Reduce tracking into buildings.
- Save money with reduced salt application.
- Save infrastructure: less salt, less corrosion.
- Look for opportunities to close extra building entrances during the winter. High maintenance, non-essential entrances are perfect candidates.
To determine the amount of deicer needed for steps, stairs, and small sites:
- Refer to the application rate chart.
- For those who do maintenance as a small part of their job, it is unlikely they will ever use an application rate chart. Here are some guidelines to get them closer to the proper rates. The goal should be:
- Even spread pattern with granules no farther than 3 in. apart
- Even spread pattern with no granules touching each other
- No piles of deicer
- No deicer on dry pavement
- No deicer in vegetation
Handheld spreaders and shakers, not scoops, should be used to apply deicer to steps and building entrances. This will save at least 50% of the salt normally used per winter without reducing the level of safety.
Parking Lot Tips
- It is hard to walk and push shopping carts through salt and sand accumulations in parking lots. Sand is ineffective once it is on the pavement. Sweep it up to prevent a slippery situation.
- Handicap parking spots are often over-salted and over-sanded. They should get the same amount of salt or sand as other areas.
- Sand/salt mix generally isn’t advised; however, it may help in freezing rain situations.
- Always plow before applying materials.
- It may be possible to use a lower rate in high traffic areas. Traffic tends to help mix and melt.
- Store snow downhill from any salt storage areas. Avoid water running through salt storage.
Calculating Parking Lot or Sidewalk Area
The amount of deicer needed is based on the size of the parking lot. Here are simple ways to calculate the area of the parking lot.
Ask the property owner for a scaled map of the facility to calculate areas.
Ask the property owner for the size of the area to be treated.
Measure the parking lot.
Use an internet mapping tool to calculate areas.
The area, or square feet, of a square or rectangle is:
Length (L) X Width (W)
The area, or square feet, of a circle is:
π r2 or 3.14 x (r x r) where r is half of the distance across the circle.
The area, or square feet, of a right triangle is:
Length (L) X Width (W) divided by 2
Measuring the area, along with knowing the pavement temperature, will allow the use of the application rate charts. This will help to reduce the amount of chemicals applied.
Take Action to Keep Surfaces Clear
Winter Maintenance Basics
- Anti-ice before the storm.
- Remove snow from surfaces as quickly as possible to reduce compaction.
- Plow before applying deicers to avoid dilution of the salt.
- Minimize deicer use during the storm.
- Never plow or blow snow into bodies of water, wetlands, traffic or into streets.
- Minimize back-up maneuvers to reduce chance of accidents.
- Limit use of salt and sand during the storm; use only to reduce bonding.
- Do not use salt to burn off snow.
- Use application rate chart to determine how much salt to use.
- Don’t apply dry salt (sodium chloride) below 15º F pavement temperature. It will not melt fast enough to help.
- Below 15° F, use a wetted salt.
- For extreme cold, skip melting and use sand.
- Clean up spills.
- Accurately record the material used at each site.
- Pay attention to its effectiveness and record observations.
- Use only what is needed based on proper application rates for the conditions.
- Put extra back in salt pile or return extra bags.
Because it uses less materials, mechanical snow and ice removal is the best strategy for protecting the water.
Loading/hauling
- Don’t overfill the truck or spreader: material will spill out as it is driven or pushed. This is a common practice and wastes salt.
- Large snow piles may need to be hauled to another site.
- Schedule this work when the mall or facility is closed to minimize conflicts with vehicles and pedestrians.
- Clean up loading area, sweep extra back into the pile.
Deicing/Anti-Icing Information
Anti-icing
Anti-icing is the most cost-effective and environmentally safe practice in winter maintenance. This is the direction to pursue. Anti-icing is a proactive approach. It should be first in a series of strategies for each winter storm. Applying a small and strategic amount of liquid on the pavement before a storm will prevent snow and ice from bonding to the pavement. This buys time for the clean-up efforts.
Anti-icing is like frying eggs: grease the pan and the eggs come out easily with no mess to clean up. Like greasing the frying pan, the purpose of anti-icing is to keep snow from sticking to the pavement. Anti-icing provides safer pavement during the event and faster clean up after the event.
Anti-icing requires about ¼ the material and 1/10 the overall cost of deicing. It can increase safety at the lowest cost, and is effective and cost-efficient when correctly used and approached with realistic expectations.
Anti-icing prevents formation of frost. It can be effective for up to several days depending on the weather conditions.
Anti-icing is quick. It is possible to treat a parking lot in a matter of minutes. It is an excellent strategy for saving time. Charging by the hour is not a desired practice when changing to anti-icing.