Information: alert-info

Phase I MS4 TMDL Application Form

Phase I MS4 TMDL Application Form Overview

This section of the page provides guidance for completing the Municipal Separate Storm Sewer System (MS4) Phase I Permit TMDL Application Form. Completing and submitting this form is a requirement for Phase I permittees who have United States Environmental Protection Agency (USEPA) approved Total Maximum Daily Load (TMDL) Wasteload Allocations (WLAs).

Attach your completed TMDL Application Form (and any accompanying supplemental information) to your submittal for reauthorization.

Description of the form

Each MS4 Permit TMDL Application Form is a custom created workbook for each Phase I permittee with United States Environmental Protection Agency (USEPA) approved Total Maximum Daily Load (TMDL) wasteload allocations (WLAs). The workbook consists of seven tabs. Two tabs are informational - for the permittee to reference while completing the other five tabs in this workbook.

Information tab

General instructions on how to complete the form, and reference links.

TMDL WLA list tab

This table is for reference only and shows ALL waste load allocations assigned to an MS4 and filtered for the specific permittee. Reference this list while completing the 'Applicable WLAs determination' tab. This list fulfills permit item Part IIB 1-5. This is a filterable list, and can be changed to show other permittees, projects, etc.

Applicable WLAs determination tab

The list in Column A contains any applicable WLAs (assigned to the permittee and USEPA approved) TMDL projects. They are listed by TMDL project name-waterbody-(waterbody id)-pollutant. The applicant needs to make a determination if they are meeting each WLA or not and type 'Yes' or 'No' in Column B. Once the determination is made, there is a macro that needs to run, and this will autopopulate the rest of the workbook.

Previously impaired waters that have been delisted, or if the permittee is listed as having no reductions required for a WLA on the TMDL WLA List would have a Yes determination on the 'Applicable WLAs determination' tab.

Warning: THE YES/NO DETERMINATION IN COLUMN B MUST BE COMPLETED ON THIS TAB BEFORE ANY OTHER TAB IS COMPLETED
decision tree for TMDL application form
Decision Tree for TMDL application form. With multiple applicable TMDL projects, you may be meeting some wasteload allocations, and not be meeting others. Depending on your determination, you may complete four tabs, or only two.

In order to complete that determination, the following may be needed:

  • An inventory of structural stormwater BMPs and non-structural BMPs (e.g. establish ordinance, education and outreach, illicit discharge elimination, etc.) within the watershed boundary to the impaired water and that are being applied toward meeting the WLA(s). To determine watershed boundaries see the specific TMDL report or retrieve shapefiles from the MPCA.
  • An estimate of annual cumulative pollutant load reductions (pounds or percent) for implemented BMPs.
  • An estimate of pollutant loading rates (lb/ac/yr) to the impaired water.

Compliance schedule tab

This tab needs to be completed for each WLA that is not being met. Permittees will fill in the target year that each of the applicable WLA(s) will be achieved for each TMDL- waterbody- pollutant project listed in column A. A narrative discussing strategies for continued BMP implementation beyond the permit term is required for each WLA in column D.

Compliance schedule BMPs tab

This tab will be filled in with proposed best management practices (BMPs) or progress toward implementation of BMPs to be achieved during the permit term, and the year each BMP is expected to be implemented ("Implementation Year(s)" column). Put an "X" in the boxes for the TMDL that corresponds with each BMP. This tab is primarily for planned practices. Previously installed BMPs will be captured through future Annual Reporting.

Narrative for WLAs met tab

This tab requires the permittee to submit required information for each applicable WLA they are claiming to meet. This should either demonstrate the cumulative estimated reductions from BMPs that serve to meet the MS4 WLA reductions included in the TMDL report OR demonstrates the MS4's existing load meets the WLA.

BMPs for WLAs met tab

This tab requires the permittee to submit required information for each applicable WLA they are claiming to meet with a list of all stormwater BMPs implemented to achieve the applicable WLA. For structural BMPs, it is required to include the BMP type and year implemented. Location in geographic coordinates (x coordinate and y coordinate) is optional.

Phase II MS4 TMDL Application Form Overview

Information: There were 5 webinars held regarding the TMDL Application Form. Each webinar covered a different topic. You can see previous webinars and materials here.

This section of the page provides guidance for completing the Phase II Municipal Separate Storm Sewer System (MS4) Permit TMDL Application Form. Completing and submitting this form is a requirement for Phase II permittees who have Total Maximum Daily Load (TMDL) Wasteload Allocations (WLAs) for total phosphorus (TP), total suspended solids (TSS), oxygen demand, or nitrate.

Attach your completed TMDL Application Form (and any accompanying supplemental information) to your submittal email for the MS4 Part 2 Application (PDF).

Description of the form

Each MS4 Permit TMDL Application Form is a custom created workbook for each permittee with United States Environmental Protection Agency (USEPA) approved Total Maximum Daily Load (TMDL) wasteload allocations (WLAs). The workbook consists of eight tabs. Three tabs are informational - for the permittee to reference in order to complete the MS4 Part 2 Permit Application, or to reference while completing the other five tabs in this workbook.

Information tab

General instructions on how to complete the form, and reference links.

Screenshot of Municipality X Applicable WLAs for Bacteria, Temperature or Chloride
Image of Applicable Bacteria, Temperature or Chloride WLAs for Municipality X. Click on Image to enlarge

Bacteria Chloride Temp tab

Informational tab- lists any applicable WLAs for bacteria, chloride or temperature TMDL projects (USEPA approved, more than a zero % reduction). Use the information in this tab to answer questions 141, 146 and 151 in the MS4 Part 2 Permit Application. If there is not a project listed for any certain pollutant, you would check the 'No' box for the corresponding question(s) in the MS4 Part 2 Permit Application.

Applicable WLAs determination tab

This tab includes two separate lists. The list in Column A contains any applicable WLAs (USEPA approved, more than a zero % reduction) for oxygen demand, nitrate, TSS, or TP TMDL projects. They are listed by TMDL project name-waterbody-(waterbody id)-pollutant. Column F lists the corresponding applicable numeric WLAs for those projects. If Columns A and F do not show any projects, you do not have any applicable WLAs, and you do not need to complete the TMDL Application. The list of permittees who have no applicable WLAs are located here. Otherwise, the applicant needs to make a determination if they are meeting each WLA or not and type 'Yes' or 'No' in Column B. Once the determination is made, there is a macro that needs to run, and this will autopopulate the rest of the workbook.

Warning: THE YES/NO DETERMINATION IN COLUMN B MUST BE COMPLETED ON THIS TAB BEFORE ANY OTHER TAB IS COMPLETED

In order to complete that determination, the following will be needed:

  • An inventory of structural stormwater BMPs and non-structural BMPs (e.g. establish ordinance, education and outreach, illicit discharge elimination, etc.) within the watershed boundary to the impaired water and that are being applied toward meeting the WLA(s). To determine watershed boundaries see the specific TMDL report or retrieve shapefiles from the MPCA.
  • An estimate of annual cumulative pollutant load reductions (pounds or percent) for implemented BMPs.
  • An estimate of pollutant loading rates (lb/ac/yr) to the impaired water.
Information: If you marked ‘Yes’ in any cells in Column B on the ‘Applicable WLAs determination’ tab on the TMDL application form, please include a brief narrative explaining the approach you used to make that determination. This narrative may be entered in Q174 on page 32 of the MS4 Part 2 Permit Application (PDF) or as a supplemental attachment (e.g., Word document).

Recommended information to include in your narrative:

• What MS4 area did you use in your determination? (i.e. MS4 Boundary layer, NCLD developed land cover, entire jurisdictional area, etc.)

• Which WLA area did you use in your determination? (TMDL study area shapefile from Sharebase site, looked at map from TMDL report, some other delineation, etc.)

• If the units in the numeric WLA column on the ‘Applicable WLAs determination’ tab and the units used in the ‘Reductions for WLA met’ tabs do not correspond, please explain how you translated from one to the other.

Example narrative: The TMDL study area for X TMDL encompasses the entire municipality. Using the MPCA Simple Estimator tool, we entered land uses from the entire jurisdictional area to determine initial TSS loads before adding any BMPs. Then we added in current BMPs implemented since the baseline year to evaluate the overall wasteload. Our initial load was X pounds (before accounting for BMPs) and our final load was Y pounds (after adding BMPs).

Please consider including any other information that is not captured within the worksheet that will help explain your determination(s).


Screenshot of Compliance Schedule tab
Screenshot of example Compliance Schedule Tab, before filling in schedule.

Compliance schedule tab

This tab needs to be completed for each WLA that is not being met. Permittees will fill in the target year that each of the applicable WLA(s) will be achieved for each TMDL- waterbody- pollutant project listed in column A. If there is an applicable WLA for total suspended solids (TSS) or total phosphorus (TP), a cumulative estimate of TSS and TP load reductions to be achieved during the permit term and the method used to determine the estimate should be entered in Columns D and E.

Compliance schedule BMPs tab

Screenshot of Compliance Schedule BMPs tab
Screenshot of example Compliance Schedule BMPs Tab, before filling in BMPs.

This tab will be filled in with proposed best management practices (BMPs) or progress toward implementation of BMPs to be achieved during the permit term, anticipated number of practices (if the permittee is planning to install more than one of any type of BMP), and the year each BMP is expected to be implemented ("Implementation Year(s)" column). Put an "X" in the boxes for the TMDL that corresponds with each BMP. This tab is primarily for planned practices. Previously installed BMPs will be captured through future Annual Reporting.

If your primary practices are going to be planning and analysis, you either need to provide enough detail on the compliance schedule tab itself by providing a comprehensive set of activities (including implementation strategy development), or provide additional detail in Q174 on page 32 of the MS4 Part 2 Application (PDF), or in a separate attachment. Additional details should include (but aren't limited to):

a. who will be completing any analyses (staff, consultants, etc),

b. if funding will be sought, who needs to approve it, and

c. in what order the planning activities and development of implementation strategies will be completed.

Reductions for WLAs met tab

Screenshot of Reductions for WLAs met tab
Screenshot of example Reduction for WLAS Met Tab, before filling in reductions.

This tab requires the permittee to submit required information for each applicable oxygen demand, nitrate, TSS and/or TP WLA they are claiming to meet. This substantiation needs to be completed using an MPCA-approved method. This should either demonstrate the cumulative estimated reductions from BMPs that serve to meet the MS4 WLA reductions included in the TMDL report OR demonstrates the MS4's existing load meets the WLA.

See Note above regarding additional information requested to explain determinations.

BMPs for WLAs met tab

Screenshot of WLAs met BMPs tab
Screenshot of example WLAs met BMPs Tab, before filling in BMPs.

This tab requires the permittee to submit required information for each applicable oxygen demand, nitrate, TSS and/or TP WLA they are claiming to meet with a list of all stormwater BMPs implemented to achieve the applicable WLA. For structural BMPs, it is required to include the BMP type, year implemented, location in geographic coordinates (x coordinate and y coordinate), and owner.

Master list tab

This table is for reference only and shows ALL waste load allocations assigned to an MS4 and all flow zones, whether they need to be reported on in the TMDL application or not. This is a filterable list, and can be changed to show other permittees, projects, etc.

FAQ

Click here to see questions and answers from February 16 TMDL Webinar -Updated with links to draft phosphorus street sweeping calculator and revised loading rates spreadsheet.

1. For categorical WLAs – Are MS4 communities to report on BMPs in just their community, or do they also present data from other communities in the watershed to demonstrate compliance or progress towards the categorical WLA?

  • Please see guidance at Guidance for categorical TMDLs. If the communities have agreed to work together, then data from other communities would be presented. If not, determine the permittee’s portion of the categorical WLA and present data towards that.

2. For categorical WLAs – Can private BMPs constructed in the watershed that have an overall pollutant reduction be included?

  • Refer to the specific TMDL’s WLA methodology, in case certain areas have been excluded from the WLA; but generally, if it discharges to the conveyance system within the watershed, it should be creditable.

3. For the Compliance Schedule BMPs tab- should it only include BMPs that have yet to be implemented/installed or should it include already installed BMPs?

  • It is allowable to include recently installed BMPs that have not yet fully reached their peak removal efficiency, or that will be improved upon over the permit cycle in your compliance schedule. (Enter them as implemented in 2020). Ultimately, the appropriate time to identify already implemented BMPs for WLAs not being met is when you complete the TMDL annual report form.

4. My Applicable WLAs Determination tab shows the percent reduction in Column I as "Not Available". Does that mean I don't have to report on that TMDL?

  • No, that is incorrect. You will have to use the Numerical WLA found in Columns F & G to determine if you are meeting your WLA. Or check this spreadsheet to see if there is a loading rate that has been calculated for the WLA in question. If you don't see the TMDL you are looking for, contact Anna Bosch.

5. Is there any guidance on how to include street sweeping for TSS removal?


Please submit questions to Anna Bosch at the MPCA.

Examples

Related pages and useful links