m
Line 1: Line 1:
 +
{{alert|This site is undergoing updates. Anticipated completion date is June, 2015.|alert-under-construction}}
 +
 
[[File:statewide karst areas.jpg|thumb|300px|alt=statewide map illustrating karst areas|<font size=3>Statewide distribution of karst features. Karst primarily occurs in limestone and dolomite formations in Southeastern Minnesota, but may occur in sandstone formations in the eastern part of the state (e.g. Pine County). Note that a statewide map such as this will be less accurate than local maps depicting karst features. Source: [http://www.mngs.umn.edu/ Minnesota Geological Survey], October 2005.</font size>]]
 
[[File:statewide karst areas.jpg|thumb|300px|alt=statewide map illustrating karst areas|<font size=3>Statewide distribution of karst features. Karst primarily occurs in limestone and dolomite formations in Southeastern Minnesota, but may occur in sandstone formations in the eastern part of the state (e.g. Pine County). Note that a statewide map such as this will be less accurate than local maps depicting karst features. Source: [http://www.mngs.umn.edu/ Minnesota Geological Survey], October 2005.</font size>]]
  

Revision as of 19:12, 3 June 2015

This site is currently undergoing revision. For more information, open this link.
This site is undergoing updates. Anticipated completion date is June, 2015.
statewide map illustrating karst areas
Statewide distribution of karst features. Karst primarily occurs in limestone and dolomite formations in Southeastern Minnesota, but may occur in sandstone formations in the eastern part of the state (e.g. Pine County). Note that a statewide map such as this will be less accurate than local maps depicting karst features. Source: Minnesota Geological Survey, October 2005.

Karst regions are predominantly found in the southeastern portion of the state and have important implications with respect to geotechnical testing, infiltration, pre-treatment and ponding of runoff. Caution must be used in interpreting the geographic depiction of karst lands. Figures showing generalized maps of active karst will be less accurate than a county-scale map of actual karstic features.

Karst regions are predominantly found in the southeastern portion of the state and have important implications with respect to geotechnical testing, infiltration, pre-treatment and ponding of runoff. Caution must be used in interpreting the geographic depiction of karst lands as illustrated in the two figures. The figure showing a generalized map of active karst will be less accurate than a county-scale map showing karstic features.

Overview of karst geology

Karst topography is a geological formation shaped by the dissolution of a layer or layers of soluble bedrock, usually carbonate rock such as limestone or dolomite, but has also been documented for weathering resistant rocks, such as quartzite, given the right conditions.

Due to subterranean drainage, there may be very limited surface water, even in the absence of any rivers and lakes. Many karst regions display distinctive surface features, with cenotes, sinkholes or dolines being the most common. However, distinctive karst surface features may be completely absent where the soluble rock is mantled, such as by glacial debris, or confined by one or more superimposed non-soluble rock strata. Some karst regions include thousands of caves, although evidence of caves large enough for human exploration is not a required characteristic of karst.

The following sources provide additional information on karst in Minnesota.

Stormwater concerns in karst settings

In karst settings where karstic conditions are known to exist, additional constraints and considerations need to be evaluated prior to implementing most structural BMPs. Of particular concern in karst settings is the formation of sinkholes as a result of hydraulic head build up and/or dissolution of carbonate rock (e.g., limestone) or erosion of bedrock (see sidebar) present underneath or adjacent to BMPs. Where karst conditions exist, there are no prescriptive rules of thumb or universally accepted management approaches because of the variability intrinsic to karst terrain. An adaptation of a familiar old saying is very appropriate: the only thing predictable about the behavior of water in a karst system is its unpredictability.

statewide map illustrating karst areas
Map illustrating sinkhole probability in Fillmore County, Southeast Minnesota. The highest sinkhole densities are on flat hilltops between or adjacent to river valleys in the western half of the county (shown in red and orange). In these locations, limestone and dolomite is the first bedrock encountered and is typically within 50 feet of the land surface. Source: Minnesota Department of Natural Resources, October 2005.
pond water disappears in karst setting
A collapsed karst feature where a stormwater pond previously existed. The site was in Woodbury, Minnesota.
pond water disappears in karst setting

Woodbury sinkhole collapse looking toward the south.

In general when underlying karst is known or even suspected to be present at the site, stormwater runoff should not be concentrated and discharged into known sinkholes, but should rather be dispersed, or soaked into the ground after adequate pre-cleaning, or conveyed to a collection and transmission system away from the area via vegetated drainageways. In other cases, it may be impossible to remove water from an area with sinkholes or away from karst geology, so common sense clean-up of the water and discharge into the karstic area is a reasonable management approach, especially if some filtering soil is available between the land surface and the karst formation.

Some communities around the country have developed karst area design specifications and soil investigation procedures for siting and designing stormwater BMPs. The following sections represent adaptations from a handful of these communities (e.g., Carroll County, MD (1996a and b); St. Johns River Water Management District, FL (2001); and Jefferson County, WV (Laughland 2003). See References.) and should be viewed only as a potential starting point. That is, the complete Minnesota experience is not represented by these resources, but they do represent products that have been put together to assist local stormwater managers deal with karst problems. Additional input was obtained from Professor Calvin Alexander (University of Minnesota) and Jeff Green (Minnesota DNR).

General stormwater management guidelines for karst areas

The following general guidelines are based on advice offered by many different sources. Again, the uncertainty characteristic of karst terrain and water movement should be the primary dictate when considering how much additional information to collect in these areas before proceeding with BMP installation. The following guidelines do not contain substantial prescriptive information because of the variability inherent to karst geology in Minnesota.

  • Developers, communities, public works agents and others managing stormwater should conduct thorough geotechnical investigations prior to proceeding with projects or building in active karst areas. The level of geotechnical investigation will depend on the likelihood of active karst being present and the regulatory requirements within the area. They should identify the karst features encountered and report to the appropriate state agency, such as the Department of Natural Resources (DNR) and Minnesota Geological Survey (MGS), and local agencies (such as the city, township or county) any existing sinkholes on a piece of land intended for development. These known occurrences should be surveyed for specific location and permanently recorded on the property deed. For transition karst areas, local discretion and the likelihood of karstic features should be used to determine the amount of geotechnical investigation.
  • Knowledge of the presence of sinkholes is an absolute indication of active karst. In these cases, an easement or reserve area should be identified on the development plats for the project so that all future landowners know of the presence of active karst on their property.
  • In many cases, identified sinkholes can and should be remediated and stormwater directed away. In other cases, remediation is not possible and the normal regional hydrologic patterns must be maintained. In this case, however, precautions should be taken to pre-treat any water that drains into a known sinkhole area. If at all possible, runoff should be routed away from active karst features because of the possibility of subsurface flow into the karst formation.
  • BMPs should be designed off-line to better manage volumes and flow rates from individual facilities.
  • Discharges from stormwater management facilities or directly from impervious surfaces should not be routed directly to the nearest sinkhole. Because active karst areas can be quite large in Minnesota, discharges may be routed to a baseflow stream via a pipe or lined ditch or channel to remove flow from the area, provided the stream does not disappear into an active karst feature.
  • Sinkholes developing within stormwater management facilities should be reported as soon as possible after the first observation of occurrence. They should then be repaired, abandoned, adapted, managed and/or observed for future changes, whichever of these are appropriate for proper management.
  • Sinkhole formation is less likely when water is allowed to soak diffusely into the soil and when stormwater is managed for smaller, more diffuse quantities that limit the volume and rates of flow handled by each BMP. Practices such as swales, bioretention, and vegetated filters should be considered first at a site. However, not all sites lend themselves to this type of management approach and could require use of the active karst region for proper management. Under these conditions, adequate precautions should be taken to assure that all potential contaminants are removed from the infiltrating stormwater.
  • Where ponds and wetlands are deemed necessary, they should be designed and constructed with a properly engineered synthetic liner. A minimum of three feet (ten feet is preferred) of unconsolidated soil material should exist between the bottom of the pond or wetland and the surface of the bedrock layer. Pond and wetland depths should be fairly uniform and limited to no more than ten feet in depth.

Table 1 provides an overview of karst related design considerations for different structural BMP groups.

Stormwater BMP selection in karst settings. Sources Karst Working Group, 2009; Minnesota Stormwater Wiki; Tennessee Permanent Stormwater Management and Design Guidance.
Link to this table

BMP Suitability in karst regions Karst considerations Construction stormwater permit restriction1
Impervious area disconnect Preferred
  • Strongly recommended for most residential lots less than 6,000 square feet.
  • Discharge point from the disconnect should extend at least 15 feet from any building foundation.
No
Bioretention with underdrain (biofiltration) Preferred
  • Requires 3 foot minimum separation distance between practice bottom and bedrock. If this is not possible, an underdrain should be used to convey the water away.
  • It’s recommended that the drainage area to an individual bioretention BMP be kept less than 20,000 square feet.
  • Larger designs that rely on exfiltration of treated runoff into the soils below are not recommended.
No
Rain tank/cistern Preferred
  • Above ground tanks are preferred to below ground.
  • Overflow of tank should extend at least 15 feet from building foundation.
No
Rooftop disconnect Preferred
  • 15 feet foundation set back.
  • Runoff should be spread diffusely across landscape.
No
Green roofs Preferred
  • Runoff should be spread diffusely across landscape.
No
Dry swale or grassed channel Preferred
  • Line with underdrains.
  • Incorporate compost amendments into the bottom of the channel to improve runoff reduction for vegetative uptake, and transpiration.
  • Do not incorporate check dams unless the swale or channel incorporates an underdrain. Otherwise small areas of infiltration would develop in the zones upgradient of the check dam where the water is captured without adequate outlet.
Warning: If the CSW permit applies, Section 16.20 prohibits permittees from constructing infiltration systems in areas within 1,000 feet upgradient or 100 feet downgradient of active karst
Yes if designed for infiltration
Media filter Preferred
  • Recommended practice in areas of shallow bedrock and soil.
No
Vegetative filter Preferred
  • Recommended practice in areas of shallow bedrock and soil.
No
Soil compost amendment Adequate No
Small scale infiltration/micro-bioinfiltration Adequate
  • Create multiple small sized infiltration BMPs to infiltrate impervious areas of 250 to 2,500 square feet.
  • Not recommended for sites identified as a stormwater hotspot.
Warning: If the CSW permit applies, Section 16.20 prohibits permittees from constructing infiltration systems in areas within 1,000 feet upgradient or 100 feet downgradient of active karst
Yes
Permeable pavement Adequate
Warning: If the CSW permit applies, Section 16.20 prohibits permittees from constructing infiltration systems in areas within 1,000 feet upgradient or 100 feet downgradient of active karst
Yes if designed for infiltration (no underdrain)
Infiltration trench or basin Adequate
  • Surface area to depth ratios of practices may need to be larger than typical basin designs to minimize depth of the BMP.
  • Confirm suitability with supporting geotechnical investigations and calculations.
  • Not recommended for sites identified as a stormwater hotspot.
  • Incorporate pre-treatment to limit risk of groundwater contamination in the event of future failure of the BMP associated with development of a karst feature. Local review authority should be consulted for approval.
Warning: If the CSW permit applies, Section 16.20 prohibits permittees from constructing infiltration systems in areas within 1,000 feet upgradient or 100 feet downgradient of active karst
Yes
Constructed wetlands Adequate
  • Requires larger surface area to drainage area ratios to limit the depth of the wetland.
  • Bedrock should act like a liner and help to maintain a permanent pool, unless fracture zone is present.
  • Consider using liner and liner cells.
Warning: If the CSW permit applies, liners are required in areas of active karst
No
Dry extended detention (ED) ponds and wet ponds Adequate
  • Requires larger surface area to drainage area ratios to limit the depth of the basin or pond. If analysis shows that the soils can support the weight of a pond then a liner should be used to prevent infiltration
Warning: If the CSW permit applies, liners are required in areas of active karst
No
Wet swale Discouraged Not feasible No
Large scale infiltration Discouraged
  • Use small scale infiltration practices instead.
Warning: If the CSW permit applies, Section 16.20 prohibits permittees from constructing infiltration systems in areas within 1,000 feet upgradient or 100 feet downgradient of active karst
Yes

1Section 16.20 of the CSW Permit prohibits prohibits permittees from constructing infiltration systems in areas within 1,000 feet upgradient or 100 feet downgradient of active karst features.


Investigation for karst areas

Karst investigations are recommended for all stormwater facilities that are located in an active karst area with known karstic features (sinkholes, solution cavities, direct hydraulic connection between surface water and ground water). The purpose of a karst investigation is to identify subsurface voids, cavities, fractures, or other discontinuities which could pose an environmental concern or a construction hazard to an existing or proposed stormwater management facility. Of special concern is preventing the possibility that an unimpeded route will be provided to move polluted runoff into the regional ground water system. The guidelines outlined below should not be interpreted as all-inclusive. The design of any geotechnical investigation should reflect the size and complexity of the proposed project, as well as local knowledge of the threat posed by the karstic geology.

Because of the complexity inherent to active karst areas, there is no single set of investigatory guidelines that works for every location. Typically, however, the sequence involves some visual observation for the presence of sinkhole features (the single easiest evidence that active karst is present), followed by an assessment of the subsurface heterogeneity (variability) of the site through geophysical investigation and/or excavation. With this information in-hand, borings or observation wells can then be accurately installed to obtain vertical data surrounding or within a karst feature. The following sections describe general guidance that may or may not be used depending upon the local situation and information deemed as needed.

Subsurface material

The investigation should determine the nature and thickness of subsurface materials, including depth to bedrock and the water table. Subsurface data may be acquired by backhoe excavation and/or soil boring. These field data should be supplemented by geophysical investigation techniques deemed appropriate by a qualified professional, which will show the location of karst formations under the surface. This is an iterative process that might need to be repeated until the desired detailed knowledge of the site is obtained and fully understood. The data listed below should be acquired under the direct supervision of a qualified and experienced karst scientist. Pertinent site information to collect includes the following:

  • bedrock characteristics (ex. type, geologic contacts, faults, geologic structure, rock surface configuration);
  • soil characteristics (ex. type, thickness, mapped unit, geologic source/history);
  • photo-geologic fracture trace map;
  • bedrock outcrop areas;
  • sinkholes and/or other closed depressions; and
  • perennial and/or intermittent streams, and their flow behavior (ex. a stream in a karst area that loses volume could be a good indication of sinkhole infiltration)

Geophysical and Dye Techniques

There are many different techniques available to view the nature of the subsurface in karst areas. These techniques can be used to detect the presence of karst features or to collect additional data on the character of a known feature. Stormwater managers in need of subsurface geophysical surveys are encouraged to obtain the services of a qualified geophysicist experienced in karst geology. Some of the geophysical techniques available for use in karst terrain include: seismic refraction, ground-penetrating radar, and electric resistivity. The surest way to determine the flow path of water in karst geology is to inject dye into the karst feature (sinkhole or fracture) and watch to see where it emerges, usually from a spring. The emergence of a known dye from a spring grants certainty to a suspicion that ground water moves in a particular pattern. Dye tracing can vary substantially in cost depending upon the local karst complexity, but it can be a reasonably priced alternative, especially when the certainty is needed.

Location of Borings

Once the character of the cover material is known and understood, borings can be used to obtain the details of the subsurface karst features at specific locations. It must be noted, however, that the local variability typical of karst areas could mean that a very different subsurface could exist a very small distance away, perhaps as little as 6 inches. To accommodate this variability, the number and type of borings must be carefully assessed. If the goal is to locate a boring down the center of a sinkhole, the previous geophysical tests or excavation results can show the likely single location to achieve that goal. If the goal is to “characterize” the entire site, then an evaluation needs to occur to determine the number and depth needed to adequately represent the site. Again, the analyst must acknowledge the extreme variability and recognize that details can easily be missed. Some general guidance for locating borings include:

  • getting at least one boring in each geologic unit present, as mapped by the Minnesota (MGS) and U.S. Geological Surveys (USGS) and local county records;
  • placing an adequate number as determined by a site investigation near on-site geologic or geomorphic indications of the presence of sinkholes or related karst features;
  • locating along photo-geologic fracture traces;
  • locating adjacent to bedrock outcrop areas;
  • locating a sufficient number to adequately represent the area under any proposed stormwater facility; and
  • documenting any areas identified as anomalies from any existing geophysical or other subsurface studies

Number and Depth of Borings

The number and depth of borings will depend entirely upon the results of the subsurface evaluation obtained from the observational, geophysical, and excavation studies, and other borings. There are no prescriptive guidelines to determine the number and depth of borings. These will have to be determined by the qualified staff conducting the BMP management evaluation based upon the data needs of the installation. The borings must extend well below the bottom elevation of the designed BMP, however, to make sure that there are no karst features that will be encountered or impacted as a result of the installation.

Identification of Material

All material identified by the excavation and geophysical studies and penetrated by the boring should be identified, as follows:

  • description, logging, and sampling for the entire depth of the boring;
  • any stains, odors, or other indications of environmental degradation;
  • a minimum laboratory analysis of two soil samples, representative of the material penetrated including potential limiting horizons, with the results compared to the field descriptions;
  • identified characteristics should include, as a minimum: color; mineral composition; grain size, shape, sorting and degree of saturation;
  • any indications of water saturation should be carefully logged, to include both perched and ground water table levels, and descriptions of soils that are mottled or gleyed should be provided. Be aware that ground water levels in karst can change dramatically in short periods of time and will not necessarily leave mottled or gleyed evidence;
  • water levels in all borings should be recorded over a time-period reflective of anticipated water level fluctuation. That is, water levels in karst geology can vary dramatically and rapidly. The boring should remain fully open to a total depth reflective of these variations and over a time that will accurately show the variation. Be advised that to get a complete picture, this could be a long-term period. Measurements could of course be collected during a period of operation of a BMP, which could be adjusted based on the findings of the data collection; and
  • when conducting a standard penetration test (SPT), estimation of soil engineering characteristics, including “N” or estimated unconfined compressive strength, should be reported.

Evaluation

At least one subsurface cross section should be provided for the BMP installation, showing confining layers, depth to bedrock, and water table (if encountered). It should extend through a central portion of the proposed installation, using the actual geophysical and boring data. A sketch map or formal construction plan indicating the location and dimension of the proposed practice and line of cross section should be included for reference, or as a base map for presentation of subsurface data.

Sinkhole Remediation

There are several approaches to sinkhole remediation if it is found that such an approach is desirable. Sinkhole sealing involves investigation, stabilization, filling and final grading. In the investigation phase, the areal extent and depth of the sinkhole(s) should be determined. The investigation may consist of excavation to bedrock, soil borings, and/or geophysical studies. Sealing small-sized sinkholes is normally achieved by digging out the sinkhole to bedrock, plugging the hole with concrete, installing several impermeable soil layers interspersed with plastic or geotextile, and crowning with an impermeable layer and topsoil. For moderate sinkholes, an engineered subsurface structure is usually required.

It is often not feasible to seal large sinkholes so other remediation options must be pursued. These could include construction of a low-head berm around the sinkhole, clean-out of the sinkhole to make sure all potentially contaminating materials are removed, landscaping and conversion of land use in the sinkhole to open space or recreation, provided it can be done in a manner that provides adequate safety. In any of these cases, pre-treatment of any stormwater entering the sinkhole is imperative. Final grading of sinkholes in open space settings should include the placement of low permeability topsoil or clay and a vegetative cover, with a positive grade maintained away from the sinkhole location to avoid ponding or infiltration, if feasible.

Monitoring of BMPs in Karst Regions

A water quality monitoring system installed, operated and maintained by the owner/operator may be desirable or even required under some circumstances, particularly where drinking water supplies are derived from ground water or in association with known sources of contamination. The location of monitoring wells or BMP performance monitoring will again depend upon the nature of the BMP and surrounding karst characteristics. As with all nonpoint source related monitoring, the capture of runoff events is the key goal. In karst areas, this could mean the installation of a monitoring system designed to reflect variable water behavior typical of karst water flow. Attempting to monitor this behavior without a thorough understanding of the local geology will be difficult and could lead to a wasted effort.