Line 34: Line 34:
 
*Along local roads in place of curb and gutter
 
*Along local roads in place of curb and gutter
 
*Parking lot islands and medians
 
*Parking lot islands and medians
 +
*Highway medians
 +
*First line of defense upstream of the stormwater system
 +
*Aesthetic amenity at civic, commercial or residential sites
 +
*Low flow conveyance in place of structural conveyance
 +
*Pretreatment prior to discharge to open water or stormwater treatment facilities such as infiltration basins
 +
 +
'''Design considerations'''  The size of the swale including length, width, and depth is dependent upon soil conditions, ground water level, the area discharging stormwater, the amount of impervious area discharging stormwater, and the topography of the contributing area. The recommendations below are from Chapter 12 of the Minnesota Stormwater Manual.
 +
*Size the bottom width, depth, length, and slope necessary to store the water quality volume with less than 18 inches of ponding at the downstream end
 +
*Slope should not exceed 5 percent (1 to 2 percent recommended)
 +
*Bottom width should range from 2 to 8 feet
 +
*Ensure that side slopes are no greater than 3:1 (4:1 recommended)
 +
*The maximum drainage area should be five acres with a maximum site slope of 20 percent
 +
*Swales are designed to meet a runoff velocity target for a water quality storm as well as the peak discharge from a 2-year design storm. The runoff velocity should not exceed one foot-per-second during the water quality storm.
 +
*Swales can be designed to pass larger storms and serve as conveyance tools
 +
*Pre-treatment can be created by placing checkdams across the channel below pipe inflows, and at various other points along the channel
 +
*Provide a 30-inch deep filter bed of amended soil in the swale if check dams are used to promote infiltration
 +
*The swale’s ability to infiltrate is dependant upon the soils. In addition a swale will not function optimally in an area where the ground water table meets the bottom of the swale. Soils and ground water table level should be evaluated before installation. Provide a minimum 3-foot depth to bedrock or the seasonally high water table.
 +
 +
'''Vegetation'''  Vegetation can range from tall plants and grasses to a short turf grass depending upon the desired application of the swale. Any vegetation used should be water tolerant. Native vegetation is preferred with its ability to uptake

Revision as of 16:02, 8 March 2017

Vegetated Swales & Buffer Strips

Utilizing vegetated swales and buffer strips to prevent pollution

Stormwater runoff from residential, commercial, industrial and agricultural land uses contains pollutants that can contaminate water bodies. Stormwater runoff from impervious surfaces also can increase runoff velocities and contribute to streambank erosion. Swales and buffer strips are a type of stormwater treatment composed of vegetation and a porous subsoil medium. Buffer strips are vegetated areas adjacent to a waterway that prohibit stormwater runoff from flowing directly into a water body.

The vegetation catches pollutants carried by stormwater, decreases the rate of flow and volume of runoff, and stabilizes the soil on the shoreline or bank, lessening erosion caused by runoff. A swale is a long, vegetated depression often used as a water conveyance system which is also designed to infiltrate water and remove sediment and pollutants from runoff. A swale, therefore, assists in recharging ground water and managing stormwater runoff quantity and quality. This fact sheet provides guidance on the design, implementation and maintenance of vegetated swales and buffer strips and on programs to educate the public and decision makers about installing them.

Benefits / Pollution Reduction

Properly designed swales and buffers protect and separate a stream, lake or wetland from future disturbance or encroachment and sustain the integrity of stream ecosystem habitats. Maintaining a buffer or swale upstream of surface waters reduces pollutant impacts from sediment, phosphorus, nitrogen and high temperature waters. Additional benefits include ground water recharge, channel protection, erosion control, aquatic and terrestrial riparian habitat, flood control and recreational and educational opportunities.

Swales and buffer, when constructed properly, can remove a series of pollutants from stormwater runoff. Water quality removal rates for are variable and depend on a number of factors including slope, width, and vegetation. The Minnesota Stormwater Manual contains relevant data on pollutant removal efficiencies.

===Program Development & Implementation===\ Programs designed to facilitate the installation of swales and buffers for water quality protection take into account both the mechanism of implementation and the ideal design characteristics for maximum effectiveness. For additional information on developing a buffer ordinance see the Establishing a Buffer Ordinance fact sheet. The following elements can be implemented in a vegetated swale and buffer initiative.

Awareness Campaigns

Awareness campaigns inform businesses, developers, and property owners of the benefits of vegetated swales and buffers. Efforts can contribute to encouraging individuals and organizations to implement buffers on a voluntary basis, educating individuals on proper installation and maintenance. Suggested educational methods include:

Brochures Develop informative brochures, and guidance for specific audiences such as businesses, contractors, developers, homeowners associations and garden clubs.

Signage at municipal installations Locate signage at parks, government buildings, and parking lots identifying swales and buffers and explaining their functions and benefits.

Workshops and seminars Workshops and seminars can be used to provide needed technical assistance to homeowners, property owners and citizens for establishing a swale or buffer on their property.

Vegetated Swale Design

Vegetated swales are linear, channel-like surface depressions that can be utilized as conveyance to direct stormwater away from or around a structure, for treatment to remove pollutants from stormwater, to promote infiltration of runoff into the ground and as volume control for stormwater runoff. Vegetated swales can also be landscaped to provide an aesthetic appeal and provide natural habitat within an urban setting.

Applications

  • Natural drainage on a residential lot
  • Along local roads in place of curb and gutter
  • Parking lot islands and medians
  • Highway medians
  • First line of defense upstream of the stormwater system
  • Aesthetic amenity at civic, commercial or residential sites
  • Low flow conveyance in place of structural conveyance
  • Pretreatment prior to discharge to open water or stormwater treatment facilities such as infiltration basins

Design considerations The size of the swale including length, width, and depth is dependent upon soil conditions, ground water level, the area discharging stormwater, the amount of impervious area discharging stormwater, and the topography of the contributing area. The recommendations below are from Chapter 12 of the Minnesota Stormwater Manual.

  • Size the bottom width, depth, length, and slope necessary to store the water quality volume with less than 18 inches of ponding at the downstream end
  • Slope should not exceed 5 percent (1 to 2 percent recommended)
  • Bottom width should range from 2 to 8 feet
  • Ensure that side slopes are no greater than 3:1 (4:1 recommended)
  • The maximum drainage area should be five acres with a maximum site slope of 20 percent
  • Swales are designed to meet a runoff velocity target for a water quality storm as well as the peak discharge from a 2-year design storm. The runoff velocity should not exceed one foot-per-second during the water quality storm.
  • Swales can be designed to pass larger storms and serve as conveyance tools
  • Pre-treatment can be created by placing checkdams across the channel below pipe inflows, and at various other points along the channel
  • Provide a 30-inch deep filter bed of amended soil in the swale if check dams are used to promote infiltration
  • The swale’s ability to infiltrate is dependant upon the soils. In addition a swale will not function optimally in an area where the ground water table meets the bottom of the swale. Soils and ground water table level should be evaluated before installation. Provide a minimum 3-foot depth to bedrock or the seasonally high water table.

Vegetation Vegetation can range from tall plants and grasses to a short turf grass depending upon the desired application of the swale. Any vegetation used should be water tolerant. Native vegetation is preferred with its ability to uptake