Green Infrastructure: This page provides information on a green stormwater infrastructure topic
image
Photo of a Infiltration trench in Lino Lakes
Photo of an infiltration trench with native vegetation in Lino Lakes

This page provides guidance for operation and maintenance (O&M) of bioretention and other stormwater infiltration practices, including above- and below-ground infiltration practices. This includes biofiltration, bioinfiltration, infiltration trenches, and infiltration basins.

Supplemental information can be found on the page called Operation and maintenance of bioretention and other stormwater infiltration practices - supplemental information. Supplemental information includes the following.


Overview of typical O&M issues

Bioretention practices and other stormwater infiltration practices (e.g. rain gardens, infiltration trenches) are vegetated landscape practices that capture, filter, and infiltrate stormwater runoff. In addition, these practices can provide ecosystem services such as nutrient cycling and storage, carbon sequestration, reduction in heat island effect, climate adaptation, and habitat for bees, butterflies, and other insects and small animals that pollinate. Bioretention and other infiltration practices may be subject to higher public visibility, greater trash loads, pedestrian traffic, vandalism, and vehicular loads, particularly in urban areas.

These practices require dedicated and regular maintenance to ensure proper and long-lasting operation and ecosystem benefits. Estimated bioretention lifespans range from 10 to 40 years (Drescher, 2012). The most frequently cited O&M concerns for infiltration practices include the following.

  • Permanent standing water or flooding due to clogging caused by organic matter, fine silts, hydrocarbons, and algal matter. Clogging can occur at the surface, or in the inlet, outlet, or underdrain pipes.
  • Runoff bypasses the practice due to incorrect grading and slopes, or because the inlet is blocked.
  • Accumulation of trash and debris within the infiltration practice.
  • Insufficient/inadequate vegetation or overcrowded vegetation .
  • Inadequate pollutant removal due to improper soil media selection.

The sections below describe best practices to prevent or minimize these common problems.

Design Phase O&M Considerations

photo of filter strip for bioretention system
Example of a filter strip serving as pretreatment for a bioretention practice.

Designers should design bioretention and infiltration practices in ways that prevent or minimize O&M issues. Examples include the following.

  • Limiting the contributing drainage area and sizing the practice in accordance to its contributing drainage area to prevent flooding issues.
  • Providing pretreatment and trash racks to prevent clogging or trash accumulation.
  • Providing a vegetation design plan, emphasizing
    • native plantings (see Plants for Stormwater Design) to enhance pollinator and wildlife habitat, improve infiltration and evapotranspiration, reduce urban heat island effect, provide optimized carbon sequestration, and provide climate adaptation. Native plantings typically require less maintenance and replacement than non-native plantings because they are adapted to the local climate;
    • site-specific plantings that take into account sun exposure, shade, proximity to traffic corners (visibility issues), interior vs exterior plantings, salt-tolerant plants, etc. The selection of plantings suitable to their immediate surroundings will minimize long-term care and replacement frequency.
  • Specifying the optimized soil media composition and depth to effectively trap or sequester nutrients (phosphorus in particular), and that can also support the desired vegetation.
  • Providing educational signage to increase public awareness.
  • Installing measures like low fencing to prevent damage from pedestrian foot traffic .

Designers should consult and include any local requirements regarding green infrastructure. O&M considerations often depend on whether the practice is located on public land, private land, or in the public right of way. For example, plantings in the public right of way that conflict with any traffic safety considerations could require increased O&M, such as pruning or complete removal.

Designers should also recognize the need to perform frequent landscaping maintenance to remove trash, check for clogging, and maintain vigorous and healthy vegetation. Designers can incorporate design solutions to facilitate maintenance activities. Examples include

  • incorporating multiple and easy site access points;
  • installing observation wells; and
  • providing recommendations of vegetation appropriate to the location.

The designer should also provide a site-specific O&M plan that includes

  • construction inspection schedule and checklists,
  • post-construction routine maintenance schedule and checklists, and
  • operating instructions for the practice (if applicable)

Example O&M plans are provided below.

For more design information and criteria for individual infiltration practices, see the Design criteria for bioretention or Design criteria for infiltration practices pages.

Construction Phase O&M Considerations

photo showing demonstration of the rake technique for bioretention
Demonstration of the rake technique with a bucket with teeth (top) and scoop technique using a bucket with a smooth blade (right). During the final pass of excavation, the rake technique should be used to break up the soil and promote exfiltration. Source: Dr. Robert Brown, ORISE Research Fellow, US EPA, Edison, NJ.

Proper construction methods and sequencing play a significant role in reducing O&M problems. Some key items during the construction phase include:

  1. Before construction begins:
    1. Ensure that the contributing drainage area is fully stabilized with vegetation prior to the beginning of construction. Also make sure that impervious areas in the contributing drainage area are clean. If this is not possible, use barriers or diversions to direct stormwater flows from the contributing drainage area away from the practice.
    2. Install any needed erosion and sediment controls in your construction site and prepare a storm water pollution prevention plan (SWPPP).
    3. Designate a stormwater supervisor to make sure someone is responsible for erosion and sediment control.
    4. Hold a pre-construction meeting with the designer and the installer to review the construction plans and the sequencing of construction.
  2. During construction:
    1. Construct any pre-treatment devices before constructing the main bioretention or infiltration system.
    2. Ensure heavy equipment does not enter the footprint of the practice to avoid compaction of the infiltration medium.
    3. Store any soil or gravel media downstream of the practice footprint to avoid clogging the infiltration medium. If this is not possible, store soil or gravel media in some type of covered or contained structure.
    4. Inspect the practice during construction to ensure that the infiltration practice is built in accordance with the approved design and standards and specifications. This includes verification of the media composition and depths. Use a detailed inspection checklists that include sign-offs by qualified individuals at critical stages of construction, to ensure that the contractor’s interpretation of the plan is acceptable to the professional designer. Example construction phase inspection checklists are provided further down below.
    5. Ensure that the plant and vegetation mix conforms to the vegetation design plan, particularly if the vegetation was selected to provide ecological function (such as pollinator habitat).
  3. After construction:
    1. Verify that the infiltration practice was built in accordance with the approved design and standards and specifications, including the pre-treatment devices as well as the main infiltration practice.
    2. Verify that the contributing drainage area is fully stabilized with vegetation prior to removing any barriers, diversions, or erosion and sediment control measures.
    3. Verify that the practice actually captures and infiltrates runoff. Conduct a full inundation test to inspect the underdrain and outflow function. Conduct an infiltration test to verify post-construction infiltration rates.
    4. Verify that the practice reduces nutrient loads. Collect inflow and outflow storm water samples and have them analyzed for nutrient concentrations.
    5. Use a detailed inspection checklist that includes sign-offs by qualified individuals at the completion of construction, to ensure that the contractor’s interpretation of the plan is acceptable to the professional designer. Example construction phase inspection checklists are provided further down below.
    6. Review and discuss the plant warranty/establishment period with the plant provider to understand the conditions under which failing plants will be replaced.
    7. Determine if stormwater should be kept offline from the practice until the seedlings are established.
    8. The design/construction team should provide the O&M team with the following information to be included in the O&M plan:
      1. The plant warranty .
      2. The “as-built” plans of the practice
      3. A list of conditions that might cause failure of the practice if not properly maintained.

Post-Construction Phase O&M

photo of rain garden O&M
Photo showing maintenance of a bioretention practice. Image: Ramsey Washington Metro Watershed District.

Effective short and long-term operation of bioretention and infiltration practices requires dedicated and routine maintenance. Proper maintenance will not only increase the expected lifespan of the facility but will improve ecological function, aesthetics, and property value. Important post-construction considerations are provided below.

  • A site-specific Operations and Maintenance Plan should be prepared by the designer prior to putting the stormwater practice into operation. This plan should provide any operating procedures related to the practices. The plan should also provide clear maintenance expectations, activities, and schedules. Include photos if possible. Be clear about who is responsible for the maintenance and the type of expertise that will be needed for distinct O&M activities. The O&M plan should include an anticipated budget for O&M activities. The O&M plan should also include an example O&M inspection checklist and an example maintenance report. Example O&M plans and inspection checklists are provided further down below.
  • A legally binding and enforceable maintenance agreement should be executed between the practice owner and the local review authority. Example maintenance agreements are provided further down below.
  • Inspection and maintenance activities are distinct and can be done as separate activities or together. Inspection will typically assess the practice for any O&M issues, whereas maintenance will address the O&M issues identified by the inspection. A dedicated inspection effort on a large number of BMPs can help prioritize maintenance activities.
  • Maintenance activities should be careful not to cause compaction or damage to the vegetation. No vehicles or stockpiling should be allowed within the footprint of the practice. Foot traffic should be kept to a minimum.
  • Maintenance activities should apply to all parts of the bioretention or infiltration practices, including the pre-treatment devices, the main bioretention/infiltration area, the vegetation, the media, and any conveyance or discharge pipes.
  • BMP areas generally should not be used as dedicated snow storage areas. Click here for additional snow and salt considerations.

Overview and schedule of general maintenance activities for bioretention and infiltration practices.
Link to this table

First Year of Operation
Activity Frequency Time period Level of effort O&M benefita
Check that there is no ponding in the pretreatment device and/or in the main treatment area. At least twice after storm events > 0.5 inches Within the first 6 months < 1 hour 1
Check for evidence of clogging in the pretreatment device and/or in the main treatment area. At least twice after storm events > 0.5 inches Within the first 6 months < 1 hour 1
Check for evidence of clogging or failing of the inlet, outlet, and bypass pipes. At least twice after storm events > 0.5 inches Within the first 6 months < 1 hour 1
Remove any stormwater diversion or barriers once seedlings are established. Once When plants are sufficiently established 1-2 hours 1,2,3,4,5
Supplemental watering during drier periods, particularly if keeping stormwater offline until plant seedlings are established. 1/week initially During first 2 months 1-2 hours 2,3,4,5,6
As needed First growing season 1-2 hours 2,3,4,5,6
Remove and replace dead plants As needed First growing season 2-4 hours 2,3,4,5,6
Spot reseeding of bare patches and eroding areas As needed First growing season 2-4 hours 1,2,3,4,5,6
After First Year of Operation
Activity Frequency Time period Level of effort O&M benefita
Check that there is no ponding in the pretreatment device and/or in the main treatment area Semi-annually 48 hours after a rain event and when ground is not frozen. Note that deep sumps can have ponding 1-2 1
Check for evidence of clogging in the pretreatment device, the inlets/outlets/bypass pipes, and in the main treatment area. Look for evidence of short circuiting or low spots that cause flow path issues. Semi-annually n spring and fall 1-2 1
Supplemental watering As needed during extended dry periods During dry periods 1-2 hours 2,3,4,5,6
Remove trash and debris from the pretreatment device and/or in the main treatment area. Monthly during rainy season All year long. Cleaning may need to be done more frequently during the summer storm season and less during the drier winter season 1-2 hours 1,5
Inspect for and remove excess sediment in the pretreatment device and/or in the main treatment area. Monthly All year long 4 hours if removal is needed 1
Check and repair eroded areas Annually In fall or spring when vegetation has died down 4 hours if repair is needed 1,2,3,4,5
Mow grass filter strips and bioretention turf cover Seasonally, but outside of the main pollinator or wildlife nesting season During growing season 1-2 hours 2,3,4,5
Weed and remove invasive plants Twice during growing season During growing season 1-2 hours 2,3,4,5
Inspect plant composition and health and replace as needed Annually In fall or spring 4 hours if plant replacement is needed 2,3,4,5,6
Prune trees and shrubs Annually In fall or spring 2-4 hours 2,3,4,5
Inspect for and repair broken inlets or pipes As needed Any time 2 hours, more if repairs are needed 1
Renew mulchb As needed In fall or spring 1-2 hours 4,5
Spring cleanup (cut back and remove last year’s material) Annually In spring 2-4 hours 2,3,4,5
Fall cleanup (removed excessive leaf litter, particularly in areas with lots of trees) Annually In fall 2-4 hours 2,3,4,5
After 5+ Years of Operation (non-routine maintenance)
Activity Frequency Time period Level of effort O&M benefita
After long term operation of the practice, some occasional and infrequent maintenance activities might be required, such as bigger repairs, soil regeneration, or redesign of key elements of the practice. As neede As needed Could be significant depending on the activity 1,2,3,4,5,6

aKey to Maintenance Benefits:

  1. Proper stormwater flow and infiltration
  2. Creation and maintenance of wildlife habitat
  3. Creation and maintenance of pollinator habitat
  4. Nutrient cycling and storage
  5. Aesthetics and public enjoyment
  6. Carbon sequestration
bNote that many practitioners are minimizing the use of mulch or using alternatives to mulch to control weeds. Using mulch can cause clogging of inlet, outlet, and bypass pipes, and can introduce invasive species such as jump worms. Alternatives to mulch include ground vegetation such as clover or sedges, or arranging plantings in more dense configurations so as to minimize use of mulch.


Common problems and how to troubleshoot them for bioretention and infiltration practices
Link to this table

Symptom Possible causes Solution
Standing water within the infiltration area for more than 48 hours The surface of the ponding area may become clogged with fine sediment over time. This might be because the pretreatment is no longer working, or there are excessive sediment loads due to erosion or high sediment loads from the contributing area.
  • Clean the pretreatment area with more frequency.
  • Scrape, clean or vacuum the infiltration area. A vacuum truck may be needed for sediment removal in the pretreatment are or BMP proper. All sediments may be subjected to the MPCA’s guidance for reuse and disposal
  • Address any erosion through more plantings.
  • Core aeration or cultivating of non-vegetated areas may be required to ensure adequate infiltration.
Rainwater does not appear to flow to the infiltration area Leaves, sediment, trash, or plant debris may be blocking the flow path. Remove these materials on a regular basis
Vegetation is not able to establish Plant selection is inappropriate for the site Consult with a landscaper or horticulturist. Check that plants are suited to the local conditions. Make sure BMP is protected from snow storage or salt application.
Erosion or scouring around the inlet Flow is obstructed by debris or improper grading Correct for drainage and flow path issues to make sure flows are evenly distributed. Make sure the flow paths are unobstructed.


Maintenance Costs

Maintenance costs will vary on a number of factors, including but not limited to:

  • Size of the practice and its contributing drainage area
  • Type of plantings used
  • Site visit frequency
  • Level of maintenance needed
  • Local weather conditions
  • Staffing needs (number of staff, external vs. internal staff, etc)
  • Travel time between sites
  • Efficiencies of scale (single GI vs. a cluster of GI)
  • Equipment needed

Preventative maintenance is key to minimizing major costs associated with repairs. A general rule of thumb to estimate maintenance costs is 3%-6% of the installation costs, but can run higher. Maintenance may be higher the first few years, while plants are being established. Maintenance costs should account for the number of hours of labor, the cost for different types of labor expertise required, and any equipment needed to successfully complete the maintenance activities.

A study published in 2017 by ASCE shows the median annual maintenance cost of bioretention devices was estimated at $0.687/sq ft with lower and higher costs of $0.13/sq ft and $2.30/sq ft, respectively. The survey also provides average annual reported maintenance costs, which range from $250 to $3880 with a median of $850 (Clary, 2017).

Useful Resources

More detailed information regarding specific maintenance activities are provided here. Topics discussed include:

  • Erosion protection and sediment monitoring, removal, and disposal – protecting your investment
  • Seeding, planting, and landscaping maintenance – keeping it looking good
  • Snow Storage
  • Sustainable service life for infiltration and bioretention BMPs
  • Maintenance agreements
  • Additional References

Case Studies

  • None identified that specifically include maintenance considerations.

Maintenance Training Documents and Videos

O&M Resource Catalog

MPCA has compiled publicly available O&M resources related to green infrastructure. This non-exhaustive catalog is intended as a resource to practitioners.

Example O&M Plans, Checklists, Reports, and Maintenance Agreements

References


Related pages

Supplemental guidance