(Volume Reduction language)
 
(11 intermediate revisions by 2 users not shown)
Line 1: Line 1:
<noinclude>{{alert|This page will be under review during September 2014|alert-under-review}}</noinclude>
 
 
 
[[File:Symbol for swale side slope.jpg|300px|thumb|alt=Schematic used as a symbol for swale side slope|<font size=3>Symbol for Swale side slope used in the MIDS calculator</font size>]]
 
[[File:Symbol for swale side slope.jpg|300px|thumb|alt=Schematic used as a symbol for swale side slope|<font size=3>Symbol for Swale side slope used in the MIDS calculator</font size>]]
  
Line 7: Line 5:
 
[[File:Swale side slope BMP parameters tab.png|300px|thumb|alt=Schematic used to show Swale side slope BMP parameters tab|<font size=3>Screen shot of the BMP Parameters tab for Swale side slope</font size>]]
 
[[File:Swale side slope BMP parameters tab.png|300px|thumb|alt=Schematic used to show Swale side slope BMP parameters tab|<font size=3>Screen shot of the BMP Parameters tab for Swale side slope</font size>]]
  
The swale side slope BMP is used in combination with one of the three main channel BMPs (Swale Main Channel, Swale Main Channel with an underdrain, or Wet Swale).  This BMP should not be used as a standalone BMP as the credits were determined as part of a swale system. The swale side slope must receive stormwater runoff from the direct watershed through sheet flow over the entire channel length.  If the stormwater flow is channelized when it reaches the swale side slope, the swale main channel component should be used without the swale side slope component.  The swale side slope BMP represents one side slope of a swale system.  If a swale contains two side slopes that each receive runoff through sheet flow from impervious surfaces, then two swale side slopes should be used in the calculator and each routed to the corresponding swale main channel BMP.  Credit toward the volume performance goal for a swale side slope is based on annual infiltration into the soils.  Due to the fact that the performance goal is an instantaneous credit following the [http://www.stormh2o.com/SW/Articles/Kerplunk_15253.aspx kerplunk method], a relationship between an annual volume reduction and the instantaneous credit was created.  All pollutants in the infiltrated water are credited as being reduced.   
+
The swale side slope BMP is used in combination with one of the three main channel BMPs (Swale Main Channel, Swale Main Channel with an underdrain, or Wet Swale).  This BMP should not be used as a standalone BMP as the credits were determined as part of a swale system. The swale side slope must receive stormwater runoff from the direct watershed through sheet flow over the entire channel length.  If the stormwater flow is channelized when it reaches the swale side slope, the swale main channel component should be used without the swale side slope component.  The swale side slope BMP represents one side slope of a swale system.  If a swale contains two side slopes that each receive runoff through sheet flow from impervious surfaces, then two swale side slopes should be used in the calculator and each routed to the corresponding swale main channel BMP.  Credit toward the volume performance goal for a swale side slope is based on annual infiltration into the soils.  Due to the fact that the performance goal is an instantaneous credit, a relationship between an annual volume reduction and the instantaneous credit was created.  All pollutants in the infiltrated water are credited as being reduced.   
  
 
==MIDS calculator user inputs for swale side slope==
 
==MIDS calculator user inputs for swale side slope==
Line 13: Line 11:
 
*'''Watershed tab'''
 
*'''Watershed tab'''
 
**'''BMP Name:''' this cell is auto-filled but can be changed by the user.
 
**'''BMP Name:''' this cell is auto-filled but can be changed by the user.
**'''Routing/downstream BMP:''' if this BMP is part of a swale system and water is being routed from this BMP to a main channel swale, the user selects the name of the BMP to which water is being routed from the dropdown box. All water must be routed to a single BMP. Note that the user must include the BMP receiving the routed water in the Schematic or the BMP will not appear in the dropdown box. This BMP can only be routed to a Swale main channel or Swale main channel (with underdrain).
+
**'''Routing/downstream BMP:''' if this BMP is part of a swale system and water is being routed from this BMP to a main channel swale, the user selects the name of the BMP to which water is being routed from the dropdown box. All water must be routed to a single BMP. Note that the user must include the BMP receiving the routed water in the Schematic or the BMP will not appear in the dropdown box. This BMP can only be routed to a Swale main channel, Swale main channel (with underdrain), or a Wet swale BMP.
**'''BMP Watershed Area:''' BMP watershed areas are the areas draining directly to the BMP. Values can be added for four soil types ([[Glossary#H|Hydrologic Soil Groups]] (HSG) A, B, C, D) and for three Land Cover types (Forest/Open Space, Managed Turf, and Impervious). The surface area of the BMP should be included as a managed turf land cover under the hydrologic soils group of the native soils located under the BMP. Units are in acres.
+
**'''BMP Watershed Area:''' BMP watershed areas are the areas draining directly to the BMP. Values can be added for four soil types ([[Glossary#H|Hydrologic Soil Groups]] (HSG) A, B, C, D) and for three Land Cover types (Forest/Open Space, Managed Turf, and Impervious Cover). The surface area of the BMP should be included as a managed turf land cover under the hydrologic soils group of the native soils located under the BMP. Units are in acres.
  
 
*'''BMP Parameters tab'''
 
*'''BMP Parameters tab'''
 
**'''Side slope [H:V]:''' The user selects the ratio between the horizontal (H) and vertical (V) components of the side slope (H:V) from a drop down menu .  The values available for selection are 3:1, 4:1, 5:1, 6:1, and 7:1. By selecting a horizontal to vertical side slope ratio, the corresponding ''Side slope'' (%) will populate automatically.  This value should be an average for the length of the swale.
 
**'''Side slope [H:V]:''' The user selects the ratio between the horizontal (H) and vertical (V) components of the side slope (H:V) from a drop down menu .  The values available for selection are 3:1, 4:1, 5:1, 6:1, and 7:1. By selecting a horizontal to vertical side slope ratio, the corresponding ''Side slope'' (%) will populate automatically.  This value should be an average for the length of the swale.
**'''Flow path length:''' This is the average diagonal distance between the highest elevation point and lowest elevation point of the side slope taken perpendicular to the main channel throughout the length of the swale. This could also be described as the width of the side slope. Units are in feet.
+
**'''Flow path length:''' This is the average diagonal distance between the highest elevation point and lowest elevation point of the side slope taken perpendicular to the main channel throughout the length of the swale. This could also be described as the width of the side slope. Units are in feet.
**'''Channel length:'''  This is the length of the side slope from the farthest point upstream to the farthest point downstream of the main channel. Flow must occur as sheet flow over the entire channel length (if not, the channel length should be adjusted to only cover areas where sheet flow occurs). Units are in feet.
+
**'''Channel length:'''  This is the length of the side slope from the farthest point upstream to the farthest point downstream of the main channel. Flow must occur as sheet flow over the entire channel length (if not, the channel length should be adjusted to only cover areas where sheet flow occurs). Units are in feet.
**'''Underlying soil - Hydrologic Soil Group:''' The user selects the most restrictive soil (lowest hydraulic conductivity) within three feet of the soil surface of the swale side slope. There are 14 soil options that fall into 4 different Hydrologic Soil Groups (Hydrologic Soil Group (HSG) A, B, C, or D) for the user. Once a soil type is selected, the corresponding [[Design infiltration rates|infiltration rate]] will populate in the ''Infiltration rate of underlying soils'' field. The user may also select ''User Defined''. This selection will activate the ''User defined infiltration rate'' cell allowing the user to enter a different value from those in the predefined selection list. The maximum allowable infiltration rate is 1.63 inches per hour.
+
**'''Underlying soil - Hydrologic Soil Group:''' The user selects the most restrictive soil (lowest hydraulic conductivity) within 5 feet of the soil surface of the swale side slope. There are 14 soil options that fall into 4 different Hydrologic Soil Groups (Hydrologic Soil Group (HSG) A, B, C, or D) for the user. Once a soil type is selected, the corresponding [[Design infiltration rates|infiltration rate]] will populate in the ''Infiltration rate of underlying soils'' field. The user may also select ''User Defined''. This selection will activate the ''User defined infiltration rate'' cell allowing the user to enter a different value from those in the predefined selection list. The maximum allowable infiltration rate is 1.63 inches per hour.
 
**'''Manning’s n (Vegetation):''' The user selects a type of vegetation cover on the swale side slope, which populates a corresponding Manning’s n. The vegetation types are mowed turf or native grasses. Mowed turf would be selected if the side slope is mowed on a consistent basis. Native grasses would be selected if the side slope is left to grow or is mowed infrequently. Once a vegetation cover is selected, the corresponding Manning’s n will populate in the ''Manning’s n'' field. The user may also select ''User Defined''. This selection will activate the ''User Defined Manning’s n'' cell allowing the user to enter a value different from the values in the predefined selection list.
 
**'''Manning’s n (Vegetation):''' The user selects a type of vegetation cover on the swale side slope, which populates a corresponding Manning’s n. The vegetation types are mowed turf or native grasses. Mowed turf would be selected if the side slope is mowed on a consistent basis. Native grasses would be selected if the side slope is left to grow or is mowed infrequently. Once a vegetation cover is selected, the corresponding Manning’s n will populate in the ''Manning’s n'' field. The user may also select ''User Defined''. This selection will activate the ''User Defined Manning’s n'' cell allowing the user to enter a value different from the values in the predefined selection list.
 
*'''BMP Summary Tab:''' The BMP Summary tab summarizes the volume and pollutant reductions provided by the specific BMP. It details the performance goal volume reductions and annual average volume, dissolved P, particulate P, and TSS load reductions. Included in the summary are the total volume and pollutant loads received by the BMP from its direct watershed, from upstream BMPs and a combined value of the two. Also included in the summary are the volume and pollutant load reductions provided by the BMP, along with the volume and pollutant loads that exit the BMP through the outflow. This outflow load and volume is what is routed to the downstream BMP, if one is defined in the Watershed tab. Finally, percent reductions are provided for the percent of the performance goal achieved, percent annual runoff volume retained, total percent annual particulate phosphorus reduction, total percent annual dissolved phosphorus reduction, total percent annual TP reduction, and total percent annual TSS reduction.
 
*'''BMP Summary Tab:''' The BMP Summary tab summarizes the volume and pollutant reductions provided by the specific BMP. It details the performance goal volume reductions and annual average volume, dissolved P, particulate P, and TSS load reductions. Included in the summary are the total volume and pollutant loads received by the BMP from its direct watershed, from upstream BMPs and a combined value of the two. Also included in the summary are the volume and pollutant load reductions provided by the BMP, along with the volume and pollutant loads that exit the BMP through the outflow. This outflow load and volume is what is routed to the downstream BMP, if one is defined in the Watershed tab. Finally, percent reductions are provided for the percent of the performance goal achieved, percent annual runoff volume retained, total percent annual particulate phosphorus reduction, total percent annual dissolved phosphorus reduction, total percent annual TP reduction, and total percent annual TSS reduction.
 +
 +
==Routing stormwater runoff to swales and swale side slopes in the MIDS Calculator==
 +
{{:Routing stormwater runoff to swales and swale side slopes in the MIDS Calculator}}
  
 
==Model input requirements and recommendations==
 
==Model input requirements and recommendations==
Line 33: Line 34:
  
 
===Required Treatment Volume===
 
===Required Treatment Volume===
''Required treatment volume'', or the volume of stormwater runoff delivered to the BMP, equals the performance goal (1.1 inches or user-specified performance goal) times the impervious area draining to the BMP.  Since no BMP can be routed to a swale side slope, no additional water can be routed to the swale side slope from an upstream BMP. Stormwater is delivered to the BMP instantaneously following the Kerplunk method.
+
''Required treatment volume'', or the volume of stormwater runoff delivered to the BMP, equals the performance goal (1.1 inches or user-specified performance goal) times the impervious area draining to the BMP.  Since no BMP can be routed to a swale side slope, no additional water can be routed to the swale side slope from an upstream BMP. Stormwater is delivered to the BMP instantaneously.
  
 
===Volume Reduction===
 
===Volume Reduction===
A swale side slope does not have storage capacity as do most other BMPs in the MIDS calculator. Volume reduction occurs only through infiltration as the stormwater travels over the side slope. To obtain an instantaneous ''Volume reduction capacity of BMP [V]'' for a swale side slope based on user inputs, annual volume reductions were determined and converted to a volume reduction capacity credit that follows the [http://www.stormh2o.com/SW/Articles/Kerplunk_15253.aspx Kerplunk method]. The ''Volume of retention provided by BMP'' is the total instantaneous volume credit that can be claimed for that BMP, and is determined by comparing the ''Volume reduction capacity of BMP [V]'' to the ''Required treatment volume''.   
+
A swale side slope does not have storage capacity as do most other BMPs in the MIDS calculator. Volume reduction occurs only through infiltration as the stormwater travels over the side slope. To obtain an instantaneous ''Volume reduction capacity of BMP [V]'' for a swale side slope based on user inputs, annual volume reductions were determined and converted to a volume reduction capacity credit. The ''Volume of retention provided by BMP'' is the total instantaneous volume credit that can be claimed for that BMP, and is determined by comparing the ''Volume reduction capacity of BMP [V]'' to the ''Required treatment volume''.   
  
 
To determine the annual volume reduction credit given for a swale side slope, the [http://wwwalker.net/p8/ P8 water quality model] was used. 55 years of hourly rainfall data were modeled for swale side slopes with various configurations of side slope, flow path length, channel length, soil infiltration rate, and Manning’s n parameters.  The model results provided annual average volume reduction rates. Multivariate regression was used to assess model results to determine the relationships between swale modeling parameters and annual volume reductions. The observed relationships are paired with the user-provided inputs to calculate an annual percent stormwater volume reduction for the swale side slope in the calculator.
 
To determine the annual volume reduction credit given for a swale side slope, the [http://wwwalker.net/p8/ P8 water quality model] was used. 55 years of hourly rainfall data were modeled for swale side slopes with various configurations of side slope, flow path length, channel length, soil infiltration rate, and Manning’s n parameters.  The model results provided annual average volume reduction rates. Multivariate regression was used to assess model results to determine the relationships between swale modeling parameters and annual volume reductions. The observed relationships are paired with the user-provided inputs to calculate an annual percent stormwater volume reduction for the swale side slope in the calculator.
  
To obtain the instantaneous ''Volume reduction capacity of BMP [V]'' side slope, the annual volume reductions are converted to an instantaneous volume reduction capacity that follows the [http://www.stormh2o.com/SW/Articles/Kerplunk_15253.aspx Kerplunk method] used for other BMPs. This is accomplished through the use of [http://stormwater.pca.state.mn.us/index.php?title=Performance_curves_for_MIDS_calculator&action=edit&redlink=1 performance curves] developed from a range of modeling scenarios. The performance curves use the annual volume reduction percentage, the infiltration rate of the underlying soils, the contributing watershed percent impervious area, and the size of the contributing watershed to calculate the ''Volume reduction capacity of BMP [V]''.
+
To obtain the instantaneous ''Volume reduction capacity of BMP [V]'' side slope, the annual volume reductions are converted to an instantaneous volume reduction capacity. This is accomplished through the use of [http://stormwater.pca.state.mn.us/index.php?title=Performance_curves_for_MIDS_calculator&action=edit&redlink=1 performance curves] developed from a range of modeling scenarios. The performance curves use the annual volume reduction percentage, the infiltration rate of the underlying soils, the contributing watershed percent impervious area, and the size of the contributing watershed to calculate the ''Volume reduction capacity of BMP [V]''.
  
 
The MIDS calculator compares the ''Volume reduction capacity of BMP [V]'' with the ''Required treatment volume'', and the lesser of the two values is used to populate the ''Volume of retention provided by BMP''. This comparison between potential and actual treatment volumes ensures that the BMP does not claim more credit than is due based on the actual amount of water routed to it. The ''Volume of retention provided by BMP'' is thus the actual volume credit the BMP receives toward the instantaneous performance goal. For example, if the BMP is oversized the user will only receive volume credit for the ''Required treatment volume'' routed to the BMP.
 
The MIDS calculator compares the ''Volume reduction capacity of BMP [V]'' with the ''Required treatment volume'', and the lesser of the two values is used to populate the ''Volume of retention provided by BMP''. This comparison between potential and actual treatment volumes ensures that the BMP does not claim more credit than is due based on the actual amount of water routed to it. The ''Volume of retention provided by BMP'' is thus the actual volume credit the BMP receives toward the instantaneous performance goal. For example, if the BMP is oversized the user will only receive volume credit for the ''Required treatment volume'' routed to the BMP.
  
 
===Pollutant Reduction===
 
===Pollutant Reduction===
Pollutant load reductions are calculated on an annual basis. For this BMP, pollutant reduction is provided through infiltration only. The annual volume reduction is calculated using the relationship between the P8 modeling results and the swale design parameters discussed in the volume reduction section. A 100 percent pollutant removal rate is applied to the stormwater infiltrated on an annual basis for total suspended solids, dissolved phosphorus, and particulate phosphorus. Pollutants not removed through infiltration are routed to the downstream swale main channel.
+
Pollutant removal is accomplished through infiltration (volume reduction) in this BMP. Pollutant load reductions are thus dependent upon the volume of water retained by the BMP, and are calculated on an annual basis. The first step in calculating annual pollutant load reductions is to determine the ''Annual retention volume provided by BMP'' as discussed in the above [[Requirements,_recommendations_and_information_for_using_swale_side_slope_as_a_BMP_in_the_MIDS_calculator#Volume reduction|Volume reduction]] section. A 100 percent pollutant removal rate is applied to this infiltrated stormwater for total suspended solids, dissolved phosphorus, and particulate phosphorus. Thus, while oversizing a BMP above the ''Required treatment volume'' will not provide additional credit towards the performance goal volume, it may provide additional annual volume and pollutant load reduction. Pollutants not removed through infiltration are routed to the downstream swale main channel.
  
 
NOTE: The user can modify event mean concentrations (EMCs) on the Site Information tab in the calculator. Default concentrations are 54.5 milligrams per liter for total suspended solids (TSS) and 0.3 milligrams per liter for total phosphorus (particulate plus dissolved). The calculator will notify the user if the default is changed. Changing the default EMC will result in changes to the total pounds of pollutant reduced.
 
NOTE: The user can modify event mean concentrations (EMCs) on the Site Information tab in the calculator. Default concentrations are 54.5 milligrams per liter for total suspended solids (TSS) and 0.3 milligrams per liter for total phosphorus (particulate plus dissolved). The calculator will notify the user if the default is changed. Changing the default EMC will result in changes to the total pounds of pollutant reduced.
Line 54: Line 55:
 
==Assumptions for swale side slope==
 
==Assumptions for swale side slope==
 
The following general assumptions apply in calculating the credits for a swale side slope. If these assumptions are not followed, the volume and pollutant reduction credits cannot be applied.
 
The following general assumptions apply in calculating the credits for a swale side slope. If these assumptions are not followed, the volume and pollutant reduction credits cannot be applied.
*The swale side slope has been properly [[Design criteria for filtration|designed]], [[Construction specifications for filtration|constructed]] and will be [[Operation and maintenance of filtration|properly maintained]] according to specifications for filtration systems.
+
*The swale side slope has been properly [[Design criteria for filtration|designed]], [[Construction specifications for filtration|constructed]], and will be [[Operation and maintenance of filtration|properly maintained]] according to specifications for filtration systems.
*The swale side slope is being used in combination with one of the tree main channel components.
+
*The swale side slope is being used in combination with one of the three swale main channel components.
  
==Swale Side Slope and Main Channel Example (Version 2)==
+
==Swale side slope and Main channel example (Version 2)==
 
Swale side slope should be used in conjunction with a main channel swale. Examples are contained in the appropriate section for the main channel swales.
 
Swale side slope should be used in conjunction with a main channel swale. Examples are contained in the appropriate section for the main channel swales.
  
*[[Requirements, recommendations and information for using swale without an underdrain as a BMP in the MIDS calculator#Swale Side Slope and Main Channel Example (Version 2)|Example for main channel swale without an underdrain]]
+
*[[Requirements, recommendations and information for using swale without an underdrain as a BMP in the MIDS calculator#Swale Side Slope and Main Channel example (version 2)|Example for Swale main channel without an underdrain]]
*[[Requirements, recommendations and information for using swale with an underdrain as a BMP in the MIDS calculator#Swale Side Slope and Main Channel with an underdrain example (Version 2)|Example for main channel swale without an underdrain]]
+
*[[Requirements, recommendations and information for using swale with an underdrain as a BMP in the MIDS calculator#Swale Side Slope and Main Channel with an underdrain example (Version 2)|Example for Swale main channel with an underdrain]]
*[[Requirements, recommendations and information for using wet swale as a BMP in the MIDS calculator#Swale Side Slope and Wet Swale Example|Example for wet swale]]
+
*[[Requirements, recommendations and information for using wet swale as a BMP in the MIDS calculator#Swale Side Slope and Wet Swale Example|Example for Wet swale]]
  
 
==Requirements==
 
==Requirements==
[[File:Illustration of depth to bedrock or wt.jpg|thumb|300px|alt=image illustrating separation distance to bedrock or seasonal high water table|<font size=2>Measurement of depth from the bottom of the infiltration BMP to the seasonally high water table or bedrock. Note that there must be a minimum of 2 feet separation when soils beneath the BMP are ripped, with a total separation distance of 3 feet or more. Infiltration BMPs include any BMP that allows water to infiltrate into the underlying soil.</font size>]]
+
[[File:3 foot separation b.png|thumb|300px|alt=image illustrating separation distance to bedrock or seasonal high water table|<font size=3>Measurement of depth from the bottom of the infiltration BMP to the seasonally high water table or bedrock. Note that there must be a minimum of 2 feet separation when soils beneath the BMP are ripped, with a total separation distance of 3 feet or more. Infiltration BMPs include any BMP that allows water to infiltrate into the underlying soil.</font size>]]
  
 
{{alert|The following are requirements of the [http://www.pca.state.mn.us/index.php/water/water-types-and-programs/stormwater/construction-stormwater/index.html Minnesota Construction Stormwater General Permit]|alert-danger}}
 
{{alert|The following are requirements of the [http://www.pca.state.mn.us/index.php/water/water-types-and-programs/stormwater/construction-stormwater/index.html Minnesota Construction Stormwater General Permit]|alert-danger}}
*3 foot separation from the bottom of an infiltration system to the seasonal high water table
+
*At least a 3 foot separation from the bottom of an infiltration system to the [[Glossary#S|seasonal high water table]]
*Use the most restrictive infiltration rate within 3 feet of the bottom of the BMP
+
*Use the most restrictive infiltration rate within 5 feet of the bottom of the BMP
*For measured infiltration rates, apply a safety factor of 2
+
*For [[Determining soil infiltration rates|measured infiltration rates]], apply a safety factor of 2
*Pretreatment for infiltration systems
+
*[[Pre-treatment|Pretreatment]] for infiltration systems
  
 
==Recommendations==
 
==Recommendations==
 
{{alert|The following are recommendations for inputs into the MIDS calculator|alert-warning}}
 
{{alert|The following are recommendations for inputs into the MIDS calculator|alert-warning}}
*Drawdown time of 24 hours when the discharge is to trout streams
+
*Drawdown time of 24 hours when the discharge is to [[Sensitive waters and other receiving waters|trout streams]]
*Field tested infiltration rates rather than table values
+
*Use of [[Determining soil infiltration rates|field tested infiltration rates]] rather than table values
  
 
==Information==
 
==Information==
Line 82: Line 83:
 
*Guidance on determining [[Design criteria for bioretention#Determine site infiltration rates (for facilities with infiltration and/or recharge)|infiltration rates]]
 
*Guidance on determining [[Design criteria for bioretention#Determine site infiltration rates (for facilities with infiltration and/or recharge)|infiltration rates]]
 
*Information on [[Stormwater infiltration and constraints on infiltration|site constraints]] (shallow soil, karst, etc.)
 
*Information on [[Stormwater infiltration and constraints on infiltration|site constraints]] (shallow soil, karst, etc.)
*Guidance on [[Pre-treatment|pretreatment]]
+
*Guidance on [[Pretreatment]]
 
*Information on [[Design criteria for bioretention#Materials specifications - filter media|soil mixes]]
 
*Information on [[Design criteria for bioretention#Materials specifications - filter media|soil mixes]]
 
*[[Construction specifications for filtration|Construction specifications for filtration BMPs]]
 
*[[Construction specifications for filtration|Construction specifications for filtration BMPs]]
Line 98: Line 99:
  
 
<noinclude>
 
<noinclude>
[[Category:MIDS calculator guidance]]
+
[[Category:Level 3 - Models and modeling/Specific models/MIDS Calculator]]
[[Category:MIDS calculator example]]
+
[[Category:Level 3 - Best management practices/Structural practices/Dry swale]]‏‎
 +
[[Category:Level 3 - Best management practices/Structural practices/Step pool‏‎]]
 +
[[Category:Level 3 - Best management practices/Structural practices/Wet swale]]
 
</noinclude>
 
</noinclude>
 
 
<!--
 
[[File:Swale no underdrain schematic for example.jpg|300px|thumb|left|alt=Schematic used to determine the watershed characteristics of your entire site|<font size=3>Schematic used to determine the watershed characteristics of your entire site.  In this example, runoff from a 1.4 acre impervious lot enters a swale side slope and then the swale main channel. pervious acres include the turf area and the swale (side slope and main channel). See Step 1.</font size>]]
 
 
[[File:Swale no underdrain site information tab.png|300px|thumb|alt=Schematic of the site information tab of the MIDS calculator|<font size=3>Schematic of the site information tab of the MIDS calculator</font size>]]
 
 
[[File:Swale no underdrain schematic tab.png|300px|thumb|alt=Schematic showing Schematic tab and drag and drop a Swale Side Slope and a Swale Main Channel icon into the Schematic Window|<font size=3>Schematic showing Schematic tab and drag and drop a Swale Side Slope and a Swale Main Channel icon into the Schematic Window</font size>]]
 
 
The runoff from a 1.4 acre parking lot surrounded by 0.359 acres of pervious turf area flows through sheet flow over one of the side slopes of a swale and into a swale main channel.  The soils across the area have a unified soils classification of SW (HSG type A soil).  A second side slope associated with the main channel does not receive runoff from impervious surfaces. Each of the swale side slopes are 800 feet long by 10 feet wide with a side slope of 5H:1V. The main channel of the swale is 800 feet long by 4 feet wide with a 2 percent slope.  The swale main channel does not have an underdrain, bioretention base or check dams.  The maintenance on the swale calls for mowing once a year.  The following steps detail how this system would be set up in the MIDS calculator.
 
 
'''Step 1''': Determine the watershed characteristics of your entire site.  For this example we have a 2.2 acre site with 1.4 acres of impervious area (parking lot) and 0.8 acres of pervious area in type A soils. The pervious area includes the turf area and the area of the swale side slopes and main channel.
 
 
'''Step 2''': Fill in the site specific information into the ''Site Information'' tab.  This includes entering a Zip Code (55414 for this example) and the watershed information from Step 1. The Managed Turf area includes the turf area, the area of the side slopes and the area of the main channel.  Zip code and impervious area must be filled in or an error message will be generated.  Other fields on this screen are optional.
 
 
'''Step 3''': Go to the Schematic tab and drag and drop a “Swale Side Slope” and a “Swale Main Channel” icon into the “Schematic Window”
 
 
'''Step 4''': Determine the watershed characteristic for each of the BMP components.  For this example the swale side slope watershed includes 1.4 acres of impervious area and 0.543 acre of pervious area (0.359 acre of turf area plus 0.184 acre of swale side slope).  The watershed of the swale main channel includes the pervious area of the main channel (0.073 acre) and the pervious area of the other swale side slope (0.184 acre) for a total pervious area of 0.257 acre.  Since no impervious area is being routed to the second swale side slope, the area can be included in the direct watershed area of the main channel. However, the second swale side slope could be placed in the calculator as an additional BMP.  Including it as a separate BMP provides a slightly greater annual volume reduction and more closely represents the true system. 
 
 
'''Step 5''': Open the BMP properties for the swale side slope by right clicking on the ''Swale Side Slope'' icon and selecting ''Edit BMP properties'', or by double clicking on the ''Swale Side Slope'' icon. 
 
 
'''Step 6''': If help is needed, click on the ''Minnesota Stormwater Manual Wiki'' link or the ''Help'' button to review input parameter specifications and calculation specific to the ''Swale Side Slope'' BMP.
 
 
'''Step 7''': Fill in the specific BMP watershed information (1.4 acres of impervious and 0.543 acre of Managed Turf on A Soils.  Route the side slope BMP to the main channel BMP.
 
 
'''Step 8''': Enter in the BMP design parameters into the ''BMP parameters'' tab.  Swale Side Slope requires the following entries.
 
*Side slope [H:V] which is 5:1
 
*Flow path length which is 10 feet
 
*Channel length, which is 800 feet
 
*Underlying soil – Hydrologic Soil Group, which is 4 SW (HSG A, 1.63 in/hr)
 
*Manning’s n (vegetation), which is Native grass
 
 
<gallery caption="MIDS calculator screen shots. Click on an image for enlarged view." widths="140px">
 
File:Swale side slope watershed tab.png|alt=Schematic showing tab used to fill in specific BMP watershed information|Schematic showing tab used to fill in specific BMP watershed information
 
File:Swale side slope BMP parameters tab.png|alt=Schematic showing results from entering BMP design parameters into the BMP parameters tab for the Swale Side slope. corresponds with Step 5 in the example.|Schematic showing results from entering BMP design parameters into the BMP parameters tab for the Swale Side slope. corresponds with Step 5 in the example.
 
File:Swale main channel watershed tab.png|alt=Schematic showing tab used to fill in specific BMP watershed information for the wet swale example. Corresponds with Step 13 in the example.|Schematic showing tab used to fill in specific BMP watershed information for the wet swale example. Corresponds with Step 13 in the example.
 
File:Swale main channel watershed tab 2.png|alt=Schematic showing tab used to fill in specific BMP watershed information|Schematic showing tab used to fill in specific BMP watershed information
 
File:Swale main channel BMP parameters tab.png|alt=Schematic showing tab used to fill in specific BMP watershed information|Schematic showing tab used to fill in specific BMP watershed information
 
</gallery>
 
 
<gallery caption="MIDS calculator screen shots of results and summary tabs.  Click on an image for enlarged view." widths="200px">
 
File:swale main channel BMP summary tab 1.png|alt=Schematic showing screen used to enter BMP design parameters into the BMP parameters tab|Schematic showing screen used to enter BMP design parameters into the BMP parameters
 
File:swale main channel BMP summary tab 2.png|alt=Schematic showing screen used to enter BMP design parameters into the BMP parameters tab|Schematic showing screen used to enter BMP design parameters into the BMP parameters
 
File:swale side slope results tab 1.png|alt=Schematic showing screen used to enter BMP design parameters into the BMP parameters tab|Schematic showing screen used to enter BMP design parameters into the BMP parameters
 
</gallery>
 
 
'''Step 9''': Click on ''BMP Summary'' tab to view results for this BMP.
 
 
'''Step 10''': Click on the ''OK'' button to exit the BMP properties screen. An arrow will appear showing that the swale side slope has been routed to the swale main channel.
 
 
'''Step 11''': Open the BMP properties window for the swale main channel by right clicking on the ''Swale main channel'' icon and selecting ''Edit BMP properties'', or by double clicking on the “Swale main channel” icon.
 
Step 12: Click on the ''Minnesota Stormwater Manual Wiki'' link or the ''Help'' button to review input parameter specifications and calculation specific to the ''Swale main channel'' BMP.
 
 
'''Step 13''': Enter in the watershed information for the swale main channel in the ''Watershed'' tab (0.257 acre for Pervious Turf on A Soil which includes the area of the main channel and the other side slope).
 
 
'''Step 14''': Enter in the BMP design parameters into the ''BMP parameters'' tab.  Swale main channel requires the following entries.
 
*Channel length, which is 800 feet
 
*Swale bottom width, which is 4 feet
 
*Channel slope, which is 2 percent (%)
 
*Underlying soil – Hydrologic Soil Group, which is 4 SW (HSG A, 1.63 in/hr)
 
*Manning’s n (vegetation), which is native grass
 
*Does the swale have a check dam, which is no
 
*Does the swale have a bioretention base, which is no
 
 
'''Step 15''': Click on ''BMP Summary'' tab to view results for this BMP.
 
 
'''Step 16''': Click on the ''OK'' button to exit the BMP properties screen.
 
 
'''Step 17''': Click on ''Results'' tab to see overall results for the site.
 
-->
 

Latest revision as of 13:31, 29 January 2023

Schematic used as a symbol for swale side slope
Symbol for Swale side slope used in the MIDS calculator
Screen shot of the Watershed tab for Swale side slope
Screen shot of the Watershed tab for Swale side slope.
Schematic used to show Swale side slope BMP parameters tab
Screen shot of the BMP Parameters tab for Swale side slope

The swale side slope BMP is used in combination with one of the three main channel BMPs (Swale Main Channel, Swale Main Channel with an underdrain, or Wet Swale). This BMP should not be used as a standalone BMP as the credits were determined as part of a swale system. The swale side slope must receive stormwater runoff from the direct watershed through sheet flow over the entire channel length. If the stormwater flow is channelized when it reaches the swale side slope, the swale main channel component should be used without the swale side slope component. The swale side slope BMP represents one side slope of a swale system. If a swale contains two side slopes that each receive runoff through sheet flow from impervious surfaces, then two swale side slopes should be used in the calculator and each routed to the corresponding swale main channel BMP. Credit toward the volume performance goal for a swale side slope is based on annual infiltration into the soils. Due to the fact that the performance goal is an instantaneous credit, a relationship between an annual volume reduction and the instantaneous credit was created. All pollutants in the infiltrated water are credited as being reduced.

MIDS calculator user inputs for swale side slope

For swale side slope BMPs, the user must input the following parameters to calculate the stormwater volume and pollutant load reductions.

  • Watershed tab
    • BMP Name: this cell is auto-filled but can be changed by the user.
    • Routing/downstream BMP: if this BMP is part of a swale system and water is being routed from this BMP to a main channel swale, the user selects the name of the BMP to which water is being routed from the dropdown box. All water must be routed to a single BMP. Note that the user must include the BMP receiving the routed water in the Schematic or the BMP will not appear in the dropdown box. This BMP can only be routed to a Swale main channel, Swale main channel (with underdrain), or a Wet swale BMP.
    • BMP Watershed Area: BMP watershed areas are the areas draining directly to the BMP. Values can be added for four soil types (Hydrologic Soil Groups (HSG) A, B, C, D) and for three Land Cover types (Forest/Open Space, Managed Turf, and Impervious Cover). The surface area of the BMP should be included as a managed turf land cover under the hydrologic soils group of the native soils located under the BMP. Units are in acres.
  • BMP Parameters tab
    • Side slope [H:V]: The user selects the ratio between the horizontal (H) and vertical (V) components of the side slope (H:V) from a drop down menu . The values available for selection are 3:1, 4:1, 5:1, 6:1, and 7:1. By selecting a horizontal to vertical side slope ratio, the corresponding Side slope (%) will populate automatically. This value should be an average for the length of the swale.
    • Flow path length: This is the average diagonal distance between the highest elevation point and lowest elevation point of the side slope taken perpendicular to the main channel throughout the length of the swale. This could also be described as the width of the side slope. Units are in feet.
    • Channel length: This is the length of the side slope from the farthest point upstream to the farthest point downstream of the main channel. Flow must occur as sheet flow over the entire channel length (if not, the channel length should be adjusted to only cover areas where sheet flow occurs). Units are in feet.
    • Underlying soil - Hydrologic Soil Group: The user selects the most restrictive soil (lowest hydraulic conductivity) within 5 feet of the soil surface of the swale side slope. There are 14 soil options that fall into 4 different Hydrologic Soil Groups (Hydrologic Soil Group (HSG) A, B, C, or D) for the user. Once a soil type is selected, the corresponding infiltration rate will populate in the Infiltration rate of underlying soils field. The user may also select User Defined. This selection will activate the User defined infiltration rate cell allowing the user to enter a different value from those in the predefined selection list. The maximum allowable infiltration rate is 1.63 inches per hour.
    • Manning’s n (Vegetation): The user selects a type of vegetation cover on the swale side slope, which populates a corresponding Manning’s n. The vegetation types are mowed turf or native grasses. Mowed turf would be selected if the side slope is mowed on a consistent basis. Native grasses would be selected if the side slope is left to grow or is mowed infrequently. Once a vegetation cover is selected, the corresponding Manning’s n will populate in the Manning’s n field. The user may also select User Defined. This selection will activate the User Defined Manning’s n cell allowing the user to enter a value different from the values in the predefined selection list.
  • BMP Summary Tab: The BMP Summary tab summarizes the volume and pollutant reductions provided by the specific BMP. It details the performance goal volume reductions and annual average volume, dissolved P, particulate P, and TSS load reductions. Included in the summary are the total volume and pollutant loads received by the BMP from its direct watershed, from upstream BMPs and a combined value of the two. Also included in the summary are the volume and pollutant load reductions provided by the BMP, along with the volume and pollutant loads that exit the BMP through the outflow. This outflow load and volume is what is routed to the downstream BMP, if one is defined in the Watershed tab. Finally, percent reductions are provided for the percent of the performance goal achieved, percent annual runoff volume retained, total percent annual particulate phosphorus reduction, total percent annual dissolved phosphorus reduction, total percent annual TP reduction, and total percent annual TSS reduction.

Routing stormwater runoff to swales and swale side slopes in the MIDS Calculator

The Minimal Impact Design Standards (MIDS) Calculator separates side slopes and the main channel of swales into separate practices. This creates the potential for inaccurately routing water, since in reality side slopes and main channels are part of a single swale system. This page provides guidance for routing water to swales in the MIDS Calculator.

Swale configuration in the MIDS Calculator

The MIDS Calculator separates swale side slopes and swale main channels into separate best management practices. This is because infiltration and pollutant retention calculations differ for the side slope and the main channel. Descriptions of modeling assumptions and calculations are found at the following links.

The primary difference between side slopes and main channels is due to increased potential for infiltration in a main channel resulting from different configurations. Specifically, infiltration in a main channel is affected by length of the swale, presence or absence of impermeable check dams, and presence or absence of engineered media. These configurations are either not available for side slopes or have limited impact on infiltration.

Potential swale configurations

routing image for swales
Image showing possible swale configurations. In scenario A, route the acres the swale channel and do not include side slopes. In Scenario B, create two side slopes, route 10 acres to each side slope, and route the side slopes to the channel. Route 5 acres to the channel. In Scenario C, create two side slopes, route 10 acres to each side slope, and route the side slopes to the channel. Do not route any acres to the channel. Click on image to enlarge.

In reality, swale side slopes and main channels are part of a single swale practice. There are three possible configurations of swales. Configuring and routing water to them correctly is essential to correctly modeling swales.

  • Swale main channels with direct discharge to it and no side slopes. This situation is rare, but there may be situations where water is discharged, such as from a pipe, directly into a swale and the swale has no side slopes.
  • Swale main channels with direct discharge to it and one or more side slopes.
  • Swale main channels with one or more side slopes and no direct discharges to the swale.

These configurations are shown in the adjacent image.

Configuring and routing water to a swale practice

  • Swale main channels with direct discharge to it and no side slopes. In this situation, only the swale main channel is used in the MIDS Calculator.
    • If the discharge water to the swale main channel is coming directly from another treatment practice, such as a bifiltration practice (e.g. bioretention with an underdrain), do not enter any contributing pervious or impervious acreage to the swale main channel. Make sure the upstream practice is being routed to the swale main channel.
    • If the discharge water to the swale main channel is not from another treatment practice, enter the impervious and pervious acres contributing to this discharge into the Watershed tab for the swale BMP properties.
    • If the discharge water to the swale main channel contains both treated and untreated water, enter only acreages contributing to the untreated discharge. Make sure the upstream BMP for the treated water is routed to the swale main channel.
  • Swale main channels with direct discharge to it and one or more side slopes. For this situation, apply the above methodology to the direct discharge to the main channel. For the side slope, enter pervious and impervious acres to the Watershed tab for the swale side slope and route the side slope to the main channel. DO NOT ROUTE THESE ACREAGES TO THE MAIN CHANNEL. If there is more than one side slope, use multiple side slopes routed to the one main channel.
  • Swale main channels with one or more side slopes and no direct discharges to the swale. If all the discharge to the main channel is from swale side slopes, enter pervious and impervious acres to the Watershed tab for the swale side slope and route the side slope to the main channel. DO NOT ROUTE THESE ACREAGES TO THE MAIN CHANNEL. If there is more than one side slope, use multiple side slopes routed to the one main channel.


Model input requirements and recommendations

If the following requirements for inputs into the MIDS calculator are not met, then an error message will inform the user to change the input to meet the requirement.

  • Infiltration rates of the underlying soils cannot exceed 1.63 inches per hour.
  • The Manning’s n value cannot be greater than 1.

Methodology

Required Treatment Volume

Required treatment volume, or the volume of stormwater runoff delivered to the BMP, equals the performance goal (1.1 inches or user-specified performance goal) times the impervious area draining to the BMP. Since no BMP can be routed to a swale side slope, no additional water can be routed to the swale side slope from an upstream BMP. Stormwater is delivered to the BMP instantaneously.

Volume Reduction

A swale side slope does not have storage capacity as do most other BMPs in the MIDS calculator. Volume reduction occurs only through infiltration as the stormwater travels over the side slope. To obtain an instantaneous Volume reduction capacity of BMP [V] for a swale side slope based on user inputs, annual volume reductions were determined and converted to a volume reduction capacity credit. The Volume of retention provided by BMP is the total instantaneous volume credit that can be claimed for that BMP, and is determined by comparing the Volume reduction capacity of BMP [V] to the Required treatment volume.

To determine the annual volume reduction credit given for a swale side slope, the P8 water quality model was used. 55 years of hourly rainfall data were modeled for swale side slopes with various configurations of side slope, flow path length, channel length, soil infiltration rate, and Manning’s n parameters. The model results provided annual average volume reduction rates. Multivariate regression was used to assess model results to determine the relationships between swale modeling parameters and annual volume reductions. The observed relationships are paired with the user-provided inputs to calculate an annual percent stormwater volume reduction for the swale side slope in the calculator.

To obtain the instantaneous Volume reduction capacity of BMP [V] side slope, the annual volume reductions are converted to an instantaneous volume reduction capacity. This is accomplished through the use of performance curves developed from a range of modeling scenarios. The performance curves use the annual volume reduction percentage, the infiltration rate of the underlying soils, the contributing watershed percent impervious area, and the size of the contributing watershed to calculate the Volume reduction capacity of BMP [V].

The MIDS calculator compares the Volume reduction capacity of BMP [V] with the Required treatment volume, and the lesser of the two values is used to populate the Volume of retention provided by BMP. This comparison between potential and actual treatment volumes ensures that the BMP does not claim more credit than is due based on the actual amount of water routed to it. The Volume of retention provided by BMP is thus the actual volume credit the BMP receives toward the instantaneous performance goal. For example, if the BMP is oversized the user will only receive volume credit for the Required treatment volume routed to the BMP.

Pollutant Reduction

Pollutant removal is accomplished through infiltration (volume reduction) in this BMP. Pollutant load reductions are thus dependent upon the volume of water retained by the BMP, and are calculated on an annual basis. The first step in calculating annual pollutant load reductions is to determine the Annual retention volume provided by BMP as discussed in the above Volume reduction section. A 100 percent pollutant removal rate is applied to this infiltrated stormwater for total suspended solids, dissolved phosphorus, and particulate phosphorus. Thus, while oversizing a BMP above the Required treatment volume will not provide additional credit towards the performance goal volume, it may provide additional annual volume and pollutant load reduction. Pollutants not removed through infiltration are routed to the downstream swale main channel.

NOTE: The user can modify event mean concentrations (EMCs) on the Site Information tab in the calculator. Default concentrations are 54.5 milligrams per liter for total suspended solids (TSS) and 0.3 milligrams per liter for total phosphorus (particulate plus dissolved). The calculator will notify the user if the default is changed. Changing the default EMC will result in changes to the total pounds of pollutant reduced.

Routing

The swale side slope BMP is designed to be part of a system with a corresponding swale main channel BMP. Therefore, a swale side slope BMP can only be routed to one of the three main channel BMPs: Swale Main Channel, Swale Main Channel (with underdrain), or Wet Swale. The swale side slope BMP should not be used as a standalone BMP. It should always be used in combination with one of the three main channel BMPs. The swale side slope BMP requires sheet flow over its surface area to receive credit. Therefore, no other BMP can be routed to the swale side slope BMP. It can only receive runoff from the direct watershed.

Assumptions for swale side slope

The following general assumptions apply in calculating the credits for a swale side slope. If these assumptions are not followed, the volume and pollutant reduction credits cannot be applied.

  • The swale side slope has been properly designed, constructed, and will be properly maintained according to specifications for filtration systems.
  • The swale side slope is being used in combination with one of the three swale main channel components.

Swale side slope and Main channel example (Version 2)

Swale side slope should be used in conjunction with a main channel swale. Examples are contained in the appropriate section for the main channel swales.

Requirements

image illustrating separation distance to bedrock or seasonal high water table
Measurement of depth from the bottom of the infiltration BMP to the seasonally high water table or bedrock. Note that there must be a minimum of 2 feet separation when soils beneath the BMP are ripped, with a total separation distance of 3 feet or more. Infiltration BMPs include any BMP that allows water to infiltrate into the underlying soil.
Warning: The following are requirements of the Minnesota Construction Stormwater General Permit

Recommendations

Caution: The following are recommendations for inputs into the MIDS calculator

Information

Information: The following information may be useful in determining inputs for the MIDS calculator

Links to MIDS pages

This page was last edited on 29 January 2023, at 13:31.