m
(25 intermediate revisions by the same user not shown)
Line 1: Line 1:
{{alert|This site is under construction. Anticipated completion date is June, 2015.|alert-under-construction}}
+
[[File:Technical information page image.png|right|100px|alt=image]]
 +
[[File:Pdf image.png|100px|thumb|left|alt=pdf image|<font size=3>[https://stormwater.pca.state.mn.us/index.php?title=File:Shallow_groundwater_-_Minnesota_Stormwater_Manual.pdf Download pdf]</font size>]]
 +
[[file:Depth to water schematic.jpg|300 px|thumb|alt=schematic illustrating depth to water|<font size=3>Schematic illustrating how depth to water is calculated. Note that a temporary mound formed as a result of infiltration is not included in the determination of depth to water. (Source: CDM Smith)</font size>]]
  
Shallow groundwater is a condition where the seasonal high groundwater table, or saturated soil, is less than 3 feet from the land surface. There is a large portion of the state (more than 50 percent) where the seasonal high water table is located less than 3 feet from the surface. In these areas it may be impossible to get the 3 feet of separation from the bottom of an infiltration practice to the seasonal high water table REQUIRED under the NPDES Construction General Permit. Non-infiltration BMPs, such as lined filtration or settling practices, should be considered in areas with shallow groundwater.
+
Shallow groundwater is a condition where the [[Glossary#S|seasonal high groundwater table]], or [[Glossary#S|saturated soil]], is less than 3 feet from the land surface. There is a large portion of the state (more than 50 percent) where the seasonal high water table is located less than 3 feet from the surface. In these areas it may be impossible to get the 3 feet of separation from the bottom of an infiltration practice to the seasonal high water table REQUIRED under the [http://stormwater.pca.state.mn.us/index.php/III._STORMWATER_DISCHARGE_DESIGN_REQUIREMENTS#III.D._PERMANENT_STORMWATER_MANAGEMENT_SYSTEM NPDES Construction General Permit] (CGP). Non-infiltration BMPs, such as lined filtration or settling practices, should be considered in areas with shallow groundwater.
  
 
==Why is shallow groundwater a concern?==
 
==Why is shallow groundwater a concern?==
Removal of some pollutants (e.g., bacteria) can occur in the vadose zone beneath the base of the BMP.  Pollutant removal in the vadose zone is attained via biological activity, chemical degradation, adsorption of pollutants to soil, and plant uptake. Shallow groundwater reduces the depth of the unsaturated soil available for treatment, leading to an increased likelihood of groundwater contamination. The vadose zone is further reduced when a groundwater mound forms. These sites present challenges to stormwater management, however these challenges can be managed. General guidelines for investigation and management are presented in the following sections.
+
Removal of some pollutants (e.g., bacteria) can occur in the [[Glossary#V|vadose zone]] beneath the base of the BMP.  Pollutant removal in the vadose zone is attained via biological activity, chemical degradation, adsorption of pollutants to soil, and plant uptake. Shallow groundwater reduces the depth of the unsaturated soil available for treatment, leading to an increased likelihood of groundwater contamination. The vadose zone is further reduced when a [http://stormwater.pca.state.mn.us/index.php/Stormwater_infiltration_and_groundwater_mounding groundwater mound] forms. These sites present challenges to stormwater management, however these challenges can be managed. General guidelines for investigation and management are presented in the following sections.
  
 
==How to investigate for shallow groundwater==
 
==How to investigate for shallow groundwater==
Investigations are recommended for all proposed stormwater facilities located on sites with a suspected shallow groundwater table. The investigation should be two-fold. First, appropriate screening tools such as soil surveys, geologic atlases, or well records should be used to determine the likelihood that the groundwater table is shallow. If a shallow groundwater table is present, a geotechnical investigation should be conducted.  
+
Investigations are recommended for all proposed stormwater facilities located on sites with a suspected shallow groundwater table. The investigation should be two-fold. First, appropriate screening tools such as [http://www.nrcs.usda.gov/wps/portal/nrcs/surveylist/soils/survey/state/?stateId=MN soil surveys], [http://www.dnr.state.mn.us/waters/groundwater_section/mapping/index.html geologic atlases], or [http://www.health.state.mn.us/divs/eh/cwi/ well records] should be used to determine the likelihood that the groundwater table is shallow. If a shallow groundwater table is present, a geotechnical investigation should be conducted.  
  
Geotechnical investigations are recommended for all proposed stormwater facilities located on sites where it is suspected that the 3 foot vertical separation between the base of the BMP and the groundwater table might not be achievable. This is needed to show that permit requirements have been met. The guidelines for how to investigate for shallow groundwater are summarized below. Guidelines for investigating all potential physical constraints to infiltration on a site are presented in the table at the bottom of this page. These guidelines should not be interpreted as all-inclusive. The size and complexity of the project will drive the extent of any subsurface investigation. Regardless of the results of the initial site screening, soils borings and infiltration tests should be performed to verify site soil conditions.
+
Geotechnical investigations are recommended for all proposed stormwater facilities located on sites where it is suspected that the 3 foot vertical separation between the base of the BMP and the groundwater table might not be achievable. This is needed to show that requirements of the CGP have been met. The guidelines for how to investigate for shallow groundwater are summarized below. Guidelines for investigating all potential physical constraints to infiltration on a site are presented [http://stormwater.pca.state.mn.us/index.php/Procedures_for_investigating_sites_with_potential_constraints_on_stormwater_infiltration in a table at this link]. These guidelines should not be interpreted as all-inclusive. The size and complexity of the project will drive the extent of any subsurface investigation. Regardless of the results of the initial site screening, soils borings and infiltration tests should be performed to verify site soil conditions.
  
 
===Subsurface material investigation===
 
===Subsurface material investigation===
Line 19: Line 21:
 
===Location of soil borings===
 
===Location of soil borings===
 
Borings should be located in order to provide representative area coverage of the proposed BMP facilities. The location of borings should be:
 
Borings should be located in order to provide representative area coverage of the proposed BMP facilities. The location of borings should be:
*Within each distinct major soil type present, as mapped by the Minnesota (MGS) and U.S. Geological Surveys (USGS) and local county records.
+
*within each distinct major soil type present, as mapped in [http://www.nrcs.usda.gov/wps/portal/nrcs/surveylist/soils/survey/state/?stateId=MN soil surveys];
*Next to bedrock outcrop areas and/or in areas with known shallow groundwater if present.
+
*next to bedrock outcrop areas and/or in areas with known shallow groundwater if present;
*Near the edges and center of the proposed practice and spaced at equal distances from one another.
+
*near the edges and center of the proposed practice and spaced at equal distances from one another; and
*Near any areas identified as anomalies from any existing geophysical studies.
+
*near any areas identified as anomalies from any existing geophysical studies.
  
 
===Number of soil borings===
 
===Number of soil borings===
 
The number of recommended borings is described below.
 
The number of recommended borings is described below.
*Infiltration trenches, bioretention, and filters - a minimum of 2 per practice.
+
*Infiltration trenches, bioretention, and filters - a minimum of 2 per practice. Note that more borings are recommended for infiltration BMPs greater than 5000 square feet in area. See [http://stormwater.pca.state.mn.us/index.php/Recommended_number_of_soil_boring,_pits,_and_permeameter_tests_for_bioretention_design here] for recommendations on number of borings for infiltration BMPs as a function of BMP size.
 
*Ponds/wetlands - a minimum of 3 per practice, or 3 per acre, whichever is greater.
 
*Ponds/wetlands - a minimum of 3 per practice, or 3 per acre, whichever is greater.
 
*Additional borings – as needed to define lateral extent of limiting horizons, or site specific conditions, where applicable.
 
*Additional borings – as needed to define lateral extent of limiting horizons, or site specific conditions, where applicable.
Line 34: Line 36:
  
 
===Identification of material===
 
===Identification of material===
All material penetrated by the boring should be identified, as follows:
+
All material penetrated by the boring should be identified, as follows.
 
*Provide descriptions, logging, and sampling for the entire depth of the boring.
 
*Provide descriptions, logging, and sampling for the entire depth of the boring.
 
*Note any stains, odors, or other indications of environmental degradation.
 
*Note any stains, odors, or other indications of environmental degradation.
 
*Perform a laboratory analysis of a minimum of 2 soil samples, representative of the material penetrated including potential limiting horizons, with the results compared to the field descriptions.
 
*Perform a laboratory analysis of a minimum of 2 soil samples, representative of the material penetrated including potential limiting horizons, with the results compared to the field descriptions.
*Identify soil characteristic including, at a minimum: color; mineral composition; grain size, shape, and sorting; and saturation.
+
*Identify soil characteristics including, at a minimum: color; mineral composition; grain size, shape, and sorting; and saturation.
 
*Log any indications of water saturation to include both perched and ground water table levels, and descriptions of soils that are mottled or gleyed (sticky clay soils typically found in waterlogged soils).
 
*Log any indications of water saturation to include both perched and ground water table levels, and descriptions of soils that are mottled or gleyed (sticky clay soils typically found in waterlogged soils).
 
*Measure water levels in all borings at the time of completion and again 24 hours after completion. The boring should remain fully open to total depth of these measurements.
 
*Measure water levels in all borings at the time of completion and again 24 hours after completion. The boring should remain fully open to total depth of these measurements.
*Estimate soil engineering characteristics, including “N” or estimated unconfined compressive strength, when conducting a standard penetration test (SPT).
+
*Estimate soil engineering characteristics, including “N” or estimated [http://www.uta.edu/ce/geotech/lab/Main/Soil%20Lab/09_UCS/UCS.pdf unconfined compressive strength], when conducting a [http://teaching.ust.hk/~civl607d/Standard%20penetration%20test.pdf standard penetration test] (SPT).
  
 
===Evaluation of findings===
 
===Evaluation of findings===
At least 1 figure showing the subsurface soil profile cross section through the proposed practice should be provided, showing confining layers, depth to bedrock, and water table (if encountered). It should extend through a central portion of the proposed practice, using the actual or projected boring data. A sketch map or formal construction plan indicating the location and dimension of the proposed practice and line of cross section should be included for reference, or as a base map for presentation of subsurface data.
+
At least one (1) figure showing the subsurface soil profile cross section through the proposed practice should be provided, showing confining layers, depth to bedrock, and water table (if encountered). It should extend through a central portion of the proposed practice, using the actual or projected boring data. A sketch map or formal construction plan indicating the location and dimension of the proposed practice and line of cross section should be included for reference, or as a base map for presentation of subsurface data.
 +
 
 +
===References for conducting geotechnical investigations===
 +
{{alert|A section providing information on soil borings is being developed for the Manual and should be available in early 2016|alert-info}}
 +
 
 +
The following references provide useful information for conducting geotechnical investigations. Note that some of these documents were written for investigations at contaminated sites.
 +
*[http://www.eng.hctx.net/pdf/guidelines_for_geotech_investigations.pdf Guidelines for Consultants Performing Geotechnical Investigations]
 +
*[https://www.dtsc.ca.gov/PublicationsForms/upload/Drilling_Logging_Sampling_Cont_Sites.pdf Drilling, Logging, and Sampling at Contaminated Sites]
 +
*[http://www.pdhonline.org/courses/g106/g106.htm Understanding the Geotechnical Report as an Engineering and Construction Reference]
  
 
==What are general stormwater management guidelines for areas with shallow groundwater?==
 
==What are general stormwater management guidelines for areas with shallow groundwater?==
 
The following investigations and design variants are HIGHLY RECOMMENDED for infiltration BMPs proposed to be located in areas of shallow groundwater:
 
The following investigations and design variants are HIGHLY RECOMMENDED for infiltration BMPs proposed to be located in areas of shallow groundwater:
*Conduct thorough geotechnical investigations with geotechnical analyses similar to those recommended for Karst regions.
+
*Conduct thorough geotechnical investigations with geotechnical analyses similar to those recommended for [[Karst|karst]] regions.
 
*Conclude the site to be infeasible for infiltration BMPs where a minimum 3 foot separation between the bottom of the BMP and groundwater cannot be achieved. The CGP prohibits infiltration BMPs when the separation distance is less than 3 feet.
 
*Conclude the site to be infeasible for infiltration BMPs where a minimum 3 foot separation between the bottom of the BMP and groundwater cannot be achieved. The CGP prohibits infiltration BMPs when the separation distance is less than 3 feet.
*Consider stormwater wetlands which require a shallower ponding depth than stormwater ponds. The disadvantage of stormwater wetlands is that the shallow depth of the wetlands often creates footprints that are larger than ponds.  
+
*Consider [[Stormwater wetlands|stormwater wetlands]] which require a shallower ponding depth than [[Stormwater ponds|stormwater ponds]]. The disadvantage of stormwater wetlands is that the shallow depth of the wetlands often creates footprints that are larger than ponds.  
*Consider a stormwater pond that will intercept the groundwater table. This approach requires close examination of the land uses to assess the potential for stormwater hotspot or other highly concentrated runoff sources that would contribute excess pollutants to the groundwater. If a stormwater hotspot is identified as a contributor, then it is the recommendation of the MPCA that the pond include a liner to protect against groundwater contamination.
+
*Consider a stormwater pond that will intercept the groundwater table. This approach requires close examination of the land uses to assess the potential for [[Potential stormwater hotspots|stormwater hotspot]] or other highly concentrated runoff sources that would contribute excess pollutants to the groundwater. If the area is a potential stormwater hotspot and there is less than 3 feet of separation from the seaonally high water table, or if the area is a confirmed stormwater hotspot, a [http://stormwater.pca.state.mn.us/index.php/Liners_for_stormwater_management#Liner_specifications Level 1 liner] is recommended to protect against groundwater contamination.
  
 
MPCA is often asked why it allows a sedimentation pond (no liner) to be constructed that may intercept the water table, but require a minimum of 3 feet of separation from the bottom of any constructed infiltration practice and the water table. The treatment processes for these two practices are very different and may help to explain the requirements. A stormwater pond achieves pollutant removal through the process of settling of suspended solids. If the basin is large enough, contains vegetation, and has a long detention time, additional treatment through biological uptake and microbial action can also occur. An infiltration practice removes pollutants through filtering that occurs in the minimum 3 foot unsaturated soil layer beneath the practice along with the biologic and microbial activity that takes place in the layer under aerobic conditions.
 
MPCA is often asked why it allows a sedimentation pond (no liner) to be constructed that may intercept the water table, but require a minimum of 3 feet of separation from the bottom of any constructed infiltration practice and the water table. The treatment processes for these two practices are very different and may help to explain the requirements. A stormwater pond achieves pollutant removal through the process of settling of suspended solids. If the basin is large enough, contains vegetation, and has a long detention time, additional treatment through biological uptake and microbial action can also occur. An infiltration practice removes pollutants through filtering that occurs in the minimum 3 foot unsaturated soil layer beneath the practice along with the biologic and microbial activity that takes place in the layer under aerobic conditions.
 
{{:Procedures for investigating sites with potential constraints on stormwater infiltration}}
 
 
<!--
 
THIS IS THE OLD LANGUAGE
 
There is a large portion of the state (more than 50 percent) where the groundwater is located less than 3 feet from the surface. In these areas it may be impossible to get the 3 feet of separation from the bottom of an infiltration practice and the groundwater table required under the NPDES [http://www.pca.state.mn.us/index.php/water/water-types-and-programs/stormwater/construction-stormwater/index.html Construction General Permit]. Other treatment methods need to be considered in these areas.
 
 
When constructing a pond that will likely intercept the groundwater table, a close examination of the land uses that will contribute runoff to the pond should be the first step in the design process. If a [[Potential stormwater hotspots|potential stormwater hotspot]] is identified as a contributor then it is the recommendation of the MPCA that the pond include a liner to protect against groundwater contamination.
 
 
MPCA is often asked why it would allow a sedimentation pond (no liner) to be constructed that may intercept the water table, but require a minimum of 3 feet of separation from the bottom of any constructed infiltration practice and the water table. The treatment processes for these two practices are very different and may help to explain the requirements. A sedimentation pond achieves treatment of stormwater runoff through the act of settling out suspended solids before the discharge point. If the basin is large enough and has a long detention time, additional treatment through biological uptake and microbial action can also occur. An infiltration practice removes pollutants through filtering that occurs in the 3 foot soil layer beneath the practice along with the biologic and microbial activity that takes place in the layer under aerobic conditions. The soils under the practice need time between events to aerate so they function hydraulically as well as provide aerobic treatment.
 
-->
 
  
 
==Related pages==
 
==Related pages==
*[[Overview of stormwater infiltration|Overview]]
+
*[[Overview of stormwater infiltration]]
 
*[[Pre-treatment considerations for stormwater infiltration]]
 
*[[Pre-treatment considerations for stormwater infiltration]]
*[[BMPs for stormwater infiltration|BMPs]]
+
*[[BMPs for stormwater infiltration]]
 
*[[Pollutant fate and transport in stormwater infiltration systems]]
 
*[[Pollutant fate and transport in stormwater infiltration systems]]
 
*[[Surface water and groundwater quality impacts from stormwater infiltration]]
 
*[[Surface water and groundwater quality impacts from stormwater infiltration]]
*[[Stormwater infiltration and groundwater mounding|Groundwater mounding]]
+
*[[Stormwater infiltration and groundwater mounding]]
*[[Stormwater infiltration and setback (separation) distances|Setback distances]]
+
*[[Stormwater infiltration and setback (separation) distances]]
 
*[[Karst]]
 
*[[Karst]]
 
*[[Shallow soils and shallow depth to bedrock]]
 
*[[Shallow soils and shallow depth to bedrock]]
 +
*[[Shallow groundwater]]
 
*[[Soils with low infiltration capacity]]
 
*[[Soils with low infiltration capacity]]
 
*[[Potential stormwater hotspots]]
 
*[[Potential stormwater hotspots]]
*[[Stormwater and wellhead protection|Wellhead protection]]
+
*[[Stormwater and wellhead protection]]
*[[Stormwater infiltrations and contaminated soils and groundwater|Contaminated soils and groundwater]]
+
*[[Stormwater infiltration and contaminated soils and groundwater]]
*[[Decision tools for stormwater infiltration|Decision tools]]
+
*[[Decision tools for stormwater infiltration]]
*[[Stormwater infiltration research needs|Research needs]]
+
*[[Stormwater infiltration research needs]]
 
*[[References for stormwater infiltration]]
 
*[[References for stormwater infiltration]]
  

Revision as of 16:32, 6 June 2022

image
schematic illustrating depth to water
Schematic illustrating how depth to water is calculated. Note that a temporary mound formed as a result of infiltration is not included in the determination of depth to water. (Source: CDM Smith)

Shallow groundwater is a condition where the seasonal high groundwater table, or saturated soil, is less than 3 feet from the land surface. There is a large portion of the state (more than 50 percent) where the seasonal high water table is located less than 3 feet from the surface. In these areas it may be impossible to get the 3 feet of separation from the bottom of an infiltration practice to the seasonal high water table REQUIRED under the NPDES Construction General Permit (CGP). Non-infiltration BMPs, such as lined filtration or settling practices, should be considered in areas with shallow groundwater.

Why is shallow groundwater a concern?

Removal of some pollutants (e.g., bacteria) can occur in the vadose zone beneath the base of the BMP. Pollutant removal in the vadose zone is attained via biological activity, chemical degradation, adsorption of pollutants to soil, and plant uptake. Shallow groundwater reduces the depth of the unsaturated soil available for treatment, leading to an increased likelihood of groundwater contamination. The vadose zone is further reduced when a groundwater mound forms. These sites present challenges to stormwater management, however these challenges can be managed. General guidelines for investigation and management are presented in the following sections.

How to investigate for shallow groundwater

Investigations are recommended for all proposed stormwater facilities located on sites with a suspected shallow groundwater table. The investigation should be two-fold. First, appropriate screening tools such as soil surveys, geologic atlases, or well records should be used to determine the likelihood that the groundwater table is shallow. If a shallow groundwater table is present, a geotechnical investigation should be conducted.

Geotechnical investigations are recommended for all proposed stormwater facilities located on sites where it is suspected that the 3 foot vertical separation between the base of the BMP and the groundwater table might not be achievable. This is needed to show that requirements of the CGP have been met. The guidelines for how to investigate for shallow groundwater are summarized below. Guidelines for investigating all potential physical constraints to infiltration on a site are presented in a table at this link. These guidelines should not be interpreted as all-inclusive. The size and complexity of the project will drive the extent of any subsurface investigation. Regardless of the results of the initial site screening, soils borings and infiltration tests should be performed to verify site soil conditions.

Subsurface material investigation

The investigation is designed to determine the nature and thickness of subsurface materials, including depth to bedrock and to the water table. Subsurface data for depth to groundwater may be acquired by soil boring or studying existing wells on the site, if present. These field data should be supplemented by geophysical investigation techniques deemed appropriate by a qualified professional, which will show the location of the groundwater formations under the surface. The data listed below should be acquired under the direct supervision of a qualified geologist, geotechnical engineer, or soil scientist who is experienced in conducting such studies. Pertinent site information should include the following:

  • Known groundwater depth or bedrock characteristics (type, geologic contacts, faults, geologic structure, rock surface configuration)
  • Soil characteristics (type, thickness, mapped unit)
  • Bedrock outcrop areas

Location of soil borings

Borings should be located in order to provide representative area coverage of the proposed BMP facilities. The location of borings should be:

  • within each distinct major soil type present, as mapped in soil surveys;
  • next to bedrock outcrop areas and/or in areas with known shallow groundwater if present;
  • near the edges and center of the proposed practice and spaced at equal distances from one another; and
  • near any areas identified as anomalies from any existing geophysical studies.

Number of soil borings

The number of recommended borings is described below.

  • Infiltration trenches, bioretention, and filters - a minimum of 2 per practice. Note that more borings are recommended for infiltration BMPs greater than 5000 square feet in area. See here for recommendations on number of borings for infiltration BMPs as a function of BMP size.
  • Ponds/wetlands - a minimum of 3 per practice, or 3 per acre, whichever is greater.
  • Additional borings – as needed to define lateral extent of limiting horizons, or site specific conditions, where applicable.

Depth of soil borings

Borings should be extended to a minimum depth of 5 feet below the lowest proposed grade within the practice unless auger/backhoe refusal is encountered.

Identification of material

All material penetrated by the boring should be identified, as follows.

  • Provide descriptions, logging, and sampling for the entire depth of the boring.
  • Note any stains, odors, or other indications of environmental degradation.
  • Perform a laboratory analysis of a minimum of 2 soil samples, representative of the material penetrated including potential limiting horizons, with the results compared to the field descriptions.
  • Identify soil characteristics including, at a minimum: color; mineral composition; grain size, shape, and sorting; and saturation.
  • Log any indications of water saturation to include both perched and ground water table levels, and descriptions of soils that are mottled or gleyed (sticky clay soils typically found in waterlogged soils).
  • Measure water levels in all borings at the time of completion and again 24 hours after completion. The boring should remain fully open to total depth of these measurements.
  • Estimate soil engineering characteristics, including “N” or estimated unconfined compressive strength, when conducting a standard penetration test (SPT).

Evaluation of findings

At least one (1) figure showing the subsurface soil profile cross section through the proposed practice should be provided, showing confining layers, depth to bedrock, and water table (if encountered). It should extend through a central portion of the proposed practice, using the actual or projected boring data. A sketch map or formal construction plan indicating the location and dimension of the proposed practice and line of cross section should be included for reference, or as a base map for presentation of subsurface data.

References for conducting geotechnical investigations

Information: A section providing information on soil borings is being developed for the Manual and should be available in early 2016

The following references provide useful information for conducting geotechnical investigations. Note that some of these documents were written for investigations at contaminated sites.

What are general stormwater management guidelines for areas with shallow groundwater?

The following investigations and design variants are HIGHLY RECOMMENDED for infiltration BMPs proposed to be located in areas of shallow groundwater:

  • Conduct thorough geotechnical investigations with geotechnical analyses similar to those recommended for karst regions.
  • Conclude the site to be infeasible for infiltration BMPs where a minimum 3 foot separation between the bottom of the BMP and groundwater cannot be achieved. The CGP prohibits infiltration BMPs when the separation distance is less than 3 feet.
  • Consider stormwater wetlands which require a shallower ponding depth than stormwater ponds. The disadvantage of stormwater wetlands is that the shallow depth of the wetlands often creates footprints that are larger than ponds.
  • Consider a stormwater pond that will intercept the groundwater table. This approach requires close examination of the land uses to assess the potential for stormwater hotspot or other highly concentrated runoff sources that would contribute excess pollutants to the groundwater. If the area is a potential stormwater hotspot and there is less than 3 feet of separation from the seaonally high water table, or if the area is a confirmed stormwater hotspot, a Level 1 liner is recommended to protect against groundwater contamination.

MPCA is often asked why it allows a sedimentation pond (no liner) to be constructed that may intercept the water table, but require a minimum of 3 feet of separation from the bottom of any constructed infiltration practice and the water table. The treatment processes for these two practices are very different and may help to explain the requirements. A stormwater pond achieves pollutant removal through the process of settling of suspended solids. If the basin is large enough, contains vegetation, and has a long detention time, additional treatment through biological uptake and microbial action can also occur. An infiltration practice removes pollutants through filtering that occurs in the minimum 3 foot unsaturated soil layer beneath the practice along with the biologic and microbial activity that takes place in the layer under aerobic conditions.

Related pages