Difference between revisions of "BMP pollutant removal for phosphorus"
m |
m |
||
| (3 intermediate revisions by the same user not shown) | |||
| Line 39: | Line 39: | ||
<tr> | <tr> | ||
<td>Dry swale</td> | <td>Dry swale</td> | ||
| − | <td> | + | <td>see [[Phosphorus credits for bioretention systems with an underdrain]]</td> |
| − | <td> | + | <td>see [[Phosphorus credits for bioretention systems with an underdrain]]</td> |
| − | <td> | + | <td>see [[Phosphorus credits for bioretention systems with an underdrain]]</td> |
</tr> | </tr> | ||
<tr> | <tr> | ||
| Line 77: | Line 77: | ||
<td rowspan="2">Stormwater ponds</td> | <td rowspan="2">Stormwater ponds</td> | ||
<td>Wet pond</td> | <td>Wet pond</td> | ||
| − | <td> | + | <td>46</td> |
<td>75</td> | <td>75</td> | ||
<td>0</td> | <td>0</td> | ||
| Line 90: | Line 90: | ||
<td rowspan="2">Stormwater wetlands</td> | <td rowspan="2">Stormwater wetlands</td> | ||
<td>Shallow wetland</td> | <td>Shallow wetland</td> | ||
| − | <td> | + | <td>38</td> |
<td>55</td> | <td>55</td> | ||
<td>0</td> | <td>0</td> | ||
| Line 116: | Line 116: | ||
<noinclude> | <noinclude> | ||
| − | [[ | + | [[Category:Level 2 - Pollutants/Pollutant removal]] |
| + | [[Category:Level 3 - General information, reference, tables, images, and archives/Tables/Pollutant removal]] | ||
</noinclude> | </noinclude> | ||
Latest revision as of 19:48, 1 August 2022
This table shows comparison of phosphorus removal for different BMPs.a,e,f Values represent the percent of incoming pollutant that is removed. Source: MPCA Minnesota Stormwater Manual.
Link to this table
| BMP group | BMP design variation | Average TP removal rate (%)b | Maximum TP removal rate (%)c | Average soluble P removal rate (%)d,f,g |
|---|---|---|---|---|
| Bioretentionf | Underdrain | see Phosphorus credits for bioretention systems with an underdrain | see Phosphorus credits for bioretention systems with an underdrain | see Phosphorus credits for bioretention systems with an underdrain |
| Infiltrationh |
|
|
|
|
| Filtration | Sand filter | 50 | 55 | 0 |
| Dry swale | see Phosphorus credits for bioretention systems with an underdrain | see Phosphorus credits for bioretention systems with an underdrain | see Phosphorus credits for bioretention systems with an underdrain | |
| Wet swale | 0 | 35 | 0 | |
| Infiltrationf | Infiltration trenchh |
|
|
|
| Infiltration basinh |
|
|
|
|
| Stormwater ponds | Wet pond | 46 | 75 | 0 |
| Multiple pond | 60 | 75 | 0 | |
| Stormwater wetlands | Shallow wetland | 38 | 55 | 0 |
| Pond/wetland | 0 |
aRemoval rates show in table are a composite of five sources:
- Caraco (Center for Watershed protection, 2001)
- Maryland Department of the Environment](2000)
- Winer (Center for Watershed Protection, 2000)
- P8 modeling (William Walker)
b Average removal efficiency expected under MPCA Sizing Rules 1 and 3
c Upper limit on phosphorus removal with increased sizing and design features, based on national review
d Average rate of soluble phosphorus removal in the literature
e See section on calculating credits for each BMP in this Manual.
f Note that the performance numbers apply only to that portion of total flow actually being treated; it does not include any runoff that bypasses the BMP
gNote that soluble P can transfer from surface water to groundwater, but this column refers only to surface water
hNote that 100% is assumed for all infiltration, but only for that portion of the flow fully treated in the infiltration facility; by-passed runoff or runoff diverted via underdrain does not receive this level of treatment.
This page was last edited on 1 August 2022, at 19:48.