m
m
 
(12 intermediate revisions by the same user not shown)
Line 9: Line 9:
 
</tr>
 
</tr>
 
<tr>
 
<tr>
<td>[http://stormwater.pca.state.mn.us/index.php/Stormwater_filtration_Best_Management_Practices Filtration BMP] with less than 3 feet of separation to seasonal saturated soil or bedrock</td>
+
<td><span title="Filtration Best Management Practices (BMPs) treat urban stormwater runoff as it flows through a filtering medium, such as sand or an organic material. They are generally used on small drainage areas (5 acres or less) and are primarily designed for pollutant removal. They are effective at removing total suspended solids (TSS), particulate phosphorus, metals, and most organics. They are less effective for soluble pollutants such as dissolved phosphorus, chloride, and nitrate."> [https://stormwater.pca.state.mn.us/index.php?title=Stormwater_filtration_Best_Management_Practices '''Filtration practices''']</span> with less than 3 feet of separation to seasonal saturated soil or bedrock</td>
 
<td>1</td>
 
<td>1</td>
<td>Required under the [http://stormwater.pca.state.mn.us/index.php/III._STORMWATER_DISCHARGE_DESIGN_REQUIREMENTS#III.D._PERMANENT_STORMWATER_MANAGEMENT_SYSTEM Construction Stormwater permit]</td>
+
<td>Required under the [https://stormwater.pca.state.mn.us/index.php?title=Construction_stormwater_program Construction Stormwater permit]</td>
 
</tr>
 
</tr>
 
<tr>
 
<tr>
<td>BMP in confirmed potential stormwater hotspot with high or very high groundwater pollution potential</td>
+
<td>BMP in confirmed potential stormwater hotspot with high or very high groundwater pollution potential or areas where infiltrating water will mobilize contaminants in soil or groundwater</td>
 
<td>1</td>
 
<td>1</td>
 
<td>Applies to all [http://stormwater.pca.state.mn.us/index.php/Post-construction_stormwater_Best_Management_Practices post-construction BMPs]. See section on [http://stormwater.pca.state.mn.us/index.php/Potential_stormwater_hotspots Potential stormwater hotspots] for more information</td>
 
<td>Applies to all [http://stormwater.pca.state.mn.us/index.php/Post-construction_stormwater_Best_Management_Practices post-construction BMPs]. See section on [http://stormwater.pca.state.mn.us/index.php/Potential_stormwater_hotspots Potential stormwater hotspots] for more information</td>
 
</tr>
 
</tr>
 
<tr>
 
<tr>
<td>Constructed ponds or constructed wetlands with less than 3 feet separation from seasonally high water table in a [http://stormwater.pca.state.mn.us/index.php/Potential_stormwater_hotspots potential hotspot]</td>
+
<td>Constructed ponds with less than 3 feet separation from seasonally high water table in a [http://stormwater.pca.state.mn.us/index.php/Potential_stormwater_hotspots potential hotspot]</td>
 
<td>1</td>
 
<td>1</td>
 
<td></td>
 
<td></td>
 
</tr>
 
</tr>
 
<tr>
 
<tr>
<td>Karst terrain with high or very high groundwater pollution potential</td>
+
<td>[https://stormwater.pca.state.mn.us/index.php?title=Stormwater_ponds Constructed wet ponds] underlain by soils with an infiltration rate of 0.3 inches per hour or greater (HSG A or B soils)</td>
 +
<td>1</td>
 +
<td>To maintain a permanent pool</td>
 +
</tr>
 +
<tr>
 +
<td>Karst terrain with high or very high groundwater pollution potential<sup>1</sup></td>
 
<td>1</td>
 
<td>1</td>
 
<td>See section on [http://stormwater.pca.state.mn.us/index.php/Karst karst] for more information</td>
 
<td>See section on [http://stormwater.pca.state.mn.us/index.php/Karst karst] for more information</td>
 +
</tr>
 +
<tr>
 +
<td>Prevent groundwater intrusion into a BMP requiring aerobic conditions, such as iron-enhanced media</td>
 +
<td>1</td>
 +
<td></td>
 
</tr>
 
</tr>
 
<tr>
 
<tr>
Line 44: Line 54:
 
</tr>
 
</tr>
 
</table>
 
</table>
 +
<font size=1><sup>1</sup> Groundwater pollution potential is determined based on hydrogeologic conditions, which are used to estimate the time of travel for water and conservative chemicals to pass through the soil and vadose zone and into groundwater.</font size>
 +
 +
<noinclude>
 +
[[Category:Level 3 - General information, reference, tables, images, and archives/Tables/General bmp information]]
 +
</noinclude>

Latest revision as of 19:53, 25 October 2022

Design process for selecting the appropriate liner level.
Link to this table

Condition Design level Note
Filtration practices with less than 3 feet of separation to seasonal saturated soil or bedrock 1 Required under the Construction Stormwater permit
BMP in confirmed potential stormwater hotspot with high or very high groundwater pollution potential or areas where infiltrating water will mobilize contaminants in soil or groundwater 1 Applies to all post-construction BMPs. See section on Potential stormwater hotspots for more information
Constructed ponds with less than 3 feet separation from seasonally high water table in a potential hotspot 1
Constructed wet ponds underlain by soils with an infiltration rate of 0.3 inches per hour or greater (HSG A or B soils) 1 To maintain a permanent pool
Karst terrain with high or very high groundwater pollution potential1 1 See section on karst for more information
Prevent groundwater intrusion into a BMP requiring aerobic conditions, such as iron-enhanced media 1
Maintain permanent pool in constructed ponds or constructed wetlands in areas underlain by geologic material that is fractured or has a high infiltration rate 2
Separation distance from a BMP cannot be achieved 2
Separate tree BMP from road, parking lot, sidewalk or adjacent walls or building foundation 2 To prevent tree root intrusion. See link

1 Groundwater pollution potential is determined based on hydrogeologic conditions, which are used to estimate the time of travel for water and conservative chemicals to pass through the soil and vadose zone and into groundwater.

This page was last edited on 25 October 2022, at 19:53.