Difference between revisions of "BMPs for stormwater infiltration"
BMPs for stormwater infiltration

Latest revision as of 17:06, 1 February 2023

Green Infrastructure: Infiltration practices can be an important tool for retention and detention of stormwater runoff and treatment of pollutants in stormwater runoff. If the practice utilizes vegetation, additional benefits may include cleaner air, carbon sequestration, improved biological habitat, and aesthetic value.

Green Infrastructure: Infiltration of stormwater, where appropriate, is a preferred practice for managing stormwater runoff, as it reduces pollutants reaching receiving waters and retains water on the landscape

Download pdf

Best management practices that infiltrate stormwater runoff into underlying soil include, but are not limited, to

infiltration basins,
infiltration trenches (includes dry wells),
underground infiltration systems,
bioinfiltration,
permeable pavements,
tree trenches and tree boxes, and
dry swale with check dams.

These are discussed briefly below. Additional information about these BMPs can be found in the following tables.

Information: Note that other practices may infiltrate water but are not specifically designed to infiltrate water at the point where water is detained. Examples include stormwater harvest and reuse systems, vegetated filter strips and swales without check dams.

Infiltration basin

Photo of an infiltration basin. Source: Clark County, Washington, with permission.

Applications and treatment capabilities for infiltration basins
Applications		Treatment capabilities^{3, 4, 5}
Residential	Yes	TSS	High⁶
Commercial	Yes	TN	Medium/high
Ultra-urban	Limited¹	TP	Medium/high
Industrial	Yes²	Chloride	Low
Highway/road	Limited	Metals	High
Recreational	Yes	Oils and grease	High
		Pathogens	High
¹ Due to a size restriction; ² Unless the infiltration practice is located in an industrial area with exposed significant materials or from vehicle fueling and maintenance areas. Infiltration BMPs are PROHIBITED in these areas; ³Underground infiltration systems may have different (likely lower) pollutant removal capabilities than what is provided in this table. These systems may have a wider application range. ⁴ This is only for the portion of flow that enters the infiltration basin; by-passed runoff does not receive treatment; ⁵ Low = < 30%; Medium = 30-65%; High = 65 -100%); ⁶ Assumes adequate pre-treatment Sources: Schueler, 1987, 1992; USEPA 1993a, 1993b; Maniquiz et al., 2010; NPRPD, 2007; California Stormwater Manual, 2009; Pennsylvania Stormwater Manual, 2006

An infiltration basin is a natural or constructed impoundment that captures, temporarily stores and infiltrates the design volume of water ( Water Quality Volume). Drawdown of this stored runoff occurs through infiltration into the surrounding naturally permeable soil. The required drawdown time is 48 hours or less. Water that is stored but not infiltrated must leave the bmp, typically through an outlet, within the required drawdown time. In the case of a constructed basin, the impoundment is created by excavation or embankment. Infiltration basins are commonly used for drainage areas of 5 to 50 acres with land slopes that are less than 20 percent. Typical depths range from 2 to 6 feet, including bounce in the basin. The sizing is to control stormwater volumes at the regional or development scale as opposed to bioretention basins (rain gardens) that are designed at the site scale. Typical dimensions range from 1,000 square feet up to an acre. Infiltration basins are commonly constructed with plant species that can tolerate and thrive in this unique growing environment.

For more information, see the following pages in this Manual.

Infiltration trench

Photo of a Infiltration trench in Lino Lakes

Applications and treatment capabilities for infiltration trenches, dry well, underground infiltration
Applications		Treatment capabilities^{3, 4}
Residential	Yes	TSS⁵	High⁵
Commercial	Yes	TN	Medium/high
Ultra-urban	Yes	TP	Medium/high
Industrial	Yes¹	Chloride	Low
Highway/road	²	Metals	High
Recreational	Yes	Oils and grease	High
		Pathogens	High
¹ Unless the infiltration practice is located in an industrial area with exposed significant materials or from vehicle fuelling and maintenance areas. Infiltration BMPs are PROHIBITED in these areas; ² Yes for infiltration trench, limited for underground infiltration, no for dry well; ³ This is only for the portion of flow that enters the infiltration basin; by-passed runoff does not receive treatment; ⁴ Low = < 30%; Medium = 30-65%; High = 65 -100%); ⁵ Assumes adequate pre-treatment Sources: Schueler, 1987, 1992; USEPA 1993a, 1993b; Maniquiz et al., 2010; NPRPD, 2007; California Stormwater Manual, 2009; Pennsylvania Stormwater Manual, 2006

An infiltration trench is a shallow excavated trench, typically 3 to 6 feet deep, that is backfilled with a coarse stone aggregate allowing for the temporary storage of runoff in the void space of the material. Drawdown of this stored runoff occurs through infiltration into the surrounding naturally permeable soil. Infiltration trenches may be modified to become stormwater tree trenches and boxes where applicable with the addition of growing medium. All water captured by the BMP must be removed within 48 hours through infiltration and/or a drain. Trenches are commonly used for drainage areas less than 5 acres in size.

Caution: To avoid an infiltration trench being classified as a Class V injection well, it is strongly recommended that the length of the trench be at least 2 times greater than the depth of the trench.

For more information, see the following pages in this Manual.

Dry wells (a.k.a. infiltration tubes, french drains, soak-away pits or soak holes)

A dry well or soak away pit is a smaller variation of an infiltration trench. It is a subsurface storage facility (a structural chamber or an excavated pit backfilled with a coarse stone aggregate) that receives and temporarily stores stormwater runoff. Discharge of this stored runoff occurs through infiltration into the surrounding naturally permeable soil. Due to their size, dry wells are typically designed to handle stormwater runoff from smaller drainage areas, less than one acre in size (e.g. roof tops).

For more information, see the following pages in this Manual.

Underground infiltration systems

Underground TrueNorthSteel infiltration system in native sandy soils

Several underground infiltration systems, including pre-manufactured pipes, vaults, and modular structures, have been developed as alternatives to infiltration basins and trenches for space-limited sites and stormwater retrofit applications. Underground infiltration systems are occasionally the only stormwater BMP options on fully developed sites or highly urban and ultra-urban environments as they can be located under other land uses such as parking lots or play areas. These systems are similar to infiltration basins and trenches in that they are designed to capture, temporarily store and infiltrate the design volume of stormwater over several days. Underground infiltration systems are generally applicable to small development sites (typically less than 10 acres) and should be installed in areas that are easily accessible to routine and non-routine maintenance. These systems should not be located in areas or below structures that cannot be excavated in the event that the system needs to be replaced or invasive maintenance is required to maintain performance.

Underground infiltration systems and dry wells have been installed below parking lots and other impervious surfaces on sites where insufficient space exists for a surface infiltration system. They are designed to temporarily store stormwater runoff before slowly infiltrating the water into the subsurface (Connecticut, 2004). There is limited information on the effectiveness of these systems in removing pollutants.

One concern is that underground infiltration may meet the U.S. Environmental Protection Agency (EPA) definition of a Class V injection well. Class V injection wells are defined as any bored, drilled, or driven shaft, or any dug hole that is deeper than its widest surface dimension. Class V injection wells can also be an improved sinkhole, or a subsurface fluid distribution system (from U.S. EPA, June 2003). The U.S. EPA administers Class V injection well permits in Minnesota. Minimum requirements for installing, permitting, and operating a Class V well is defined by the USEPA.

A second concern pertains to the overall pollutant removal effectiveness of those underground infiltration systems that do not meet the definition of a Class V injection well. The document released by the Transport Research Synthesis titled “Issues of Concern Related to Underground Infiltration Systems for Stormwater Management and Treatment” provides a good overview of the concerns related to underground infiltration systems (MNDOT, 2009). Issues identified in this report include the following.

There is potential that an underground infiltration system meets the criteria of a Class V injection well.
There is insufficient knowledge of the fate of pollutants in the subgrade below the buried infiltration systems.
Roadways and parking lots with high volumes of traffic have higher concentrations of certain pollutants, including heavy metals and PAHs.
Underground systems do not allow for the pollutant removal that is accomplished through biological activity and vegetation uptake.
The minimum separation requirement of 3 feet between the bottom of the infiltration system and the seasonally high groundwater elevation may be insufficient for adequate pollutant removal. Additional study is recommended.
Maintenance of underground systems is critical for effective pollutant removal. However, access for maintenance is challenging. There are concerns that the difficult access is preventing owners from properly maintaining these systems.

For more information, see the following pages in this Manual.

Bioinfiltration basin

Bioinfiltration basin (Source: CDM Smith)

Applications and treatment capabilities for bioinfiltration basins
Applications		Treatment capabilities^{2, 3}
Residential	Yes	TSS	High⁴
Commercial	Yes	TN	Low/Medium⁵
Ultra-urban	Limited⁷	TP	Medium/high⁶
Industrial	Yes¹	Chloride	Low
Highway/road	Yes	Metals	High
Recreational	Yes	Oils and grease	High
		Pathogens	High
¹ Unless the infiltration practice is located in an industrial area with exposed significant materials or from vehicle fuelling and maintenance areas. Infiltration BMPs are PROHIBITED in these areas; ² This is only for the portion of flow that enters the infiltration basin; by-passed runoff does not receive treatment; ³ Low = < 30%; Medium = 30-65%; High = 65 -100%); ⁴ Assumes adequate pre-treatment; ⁵ This assumes no underdrain; ⁶ Certain soil mixes can leach P; ⁷ Due to a size restriction Sources: EPA Factsheet, 1999; Davis et al., 2001, 2003, 2006; Hsieh and Davis, 2005; Hong et al., 2006; Hunt et al., 2006; NPRPD, 2007; Li and Davis, 2009; Diblasi et al., 2009; Passeport et al., 2009; Brown et at., 2011a, b; Komlos et al., 2012; Denich et al., 2013; Li and Davis, 2013; California Stormwater BMP

Bioinfiltration basins, often called rain gardens, use soil (typically engineered media or mixed soil) and native vegetation to capture runoff and remove pollutants. Both the media and underlying soil typically have high infiltration rates that allow captured water to infiltrate within a required drawdown time, usually 48 hours. Bioinfiltration systems, which lack an underdrain and are designed for infiltration, differ from biofiltration systems, which have an underdrain and are designed primarily for filtration. For more information, see the following pages in this Manual.

Permeable pavement

Permeable pavement (Source: CDM Smith)

Applications and treatment capabilities for permeable pavement
Applications		Treatment capabilities^{2, 3}
Residential	Yes	TSS	High⁴
Commercial	Yes	TN	Medium/High
Ultra-urban	Yes	Nitrate	Low/Medium
Industrial	Yes¹	TP	Medium/High
Retrofit	Yes	Chloride	Low
Highway/road	Yes	Metals	High
Recreational	Yes	Oils and grease	High
		Pathogens	⁵
¹ Unless the infiltration practice is located in an industrial area with exposed significant materials or from vehicle fuelling and maintenance areas. Infiltration BMPs are PROHIBITED in these areas; ² This is only for the portion of flow that enters the infiltration basin; by-passed runoff does not receive treatment; ³ Low = < 30%; Medium = 30-65%; High = 65 -100%); ⁴ Assumes adequate pre-treatment; ⁵ Insufficient information Source: Schueler, 1987; Pratt et al, 1999; Adams, 2003; Brattebo and Booth, 2003; Adams, 2003; Bean et al, 2007; SEMCOG, 2008; International Stormwater Database, 2012

Permeable pavements are paving surfaces that allow stormwater runoff to filter through surface voids into an underlying stone reservoir for infiltration and/or storage. They are suitable for driveways, trails, parking lots, and roadways with lighter traffic. The most commonly used permeable pavement surfaces are pervious concrete, porous asphalt, and permeable interlocking concrete pavers (PICP). All permeable pavements have a similar design layering system, consisting of a surface pavement layer, an underlying stone aggregate reservoir layer, optional underdrains for filtration and geotextile over non-compacted soil subgrade. Discharge of this stored runoff occurs through infiltration into the surrounding naturally permeable soil. The drainage area leading to permeable pavements should not exceed twice the surface area of the final pavement surface.

For more information, see the following pages in this Manual.

Tree box/Tree trench

Tree box (Source: CDM Smith)

Applications and treatment capabilities for tree box/tree trench
Applications		Treatment capabilities^{2, 3}
Residential	Yes	TSS	High⁴
Commercial	Yes	TN	Low/Medium
Ultra-urban	Yes	TP	Medium/High⁵
Industrial	Yes¹	Chloride	Low
Highway/road	No	Metals	High
Recreational	Yes	Oils and grease	High
		Pathogens	High
¹ Unless the infiltration practice is located in an industrial area with exposed significant materials or from vehicle fuelling and maintenance areas. Infiltration BMPs are PROHIBITED in these areas; ² This is only for the portion of flow that enters the infiltration basin; by-passed runoff does not receive treatment; ³ Low = < 30%; Medium = 30-65%; High = 65 -100%); ⁴ Assumes adequate pre-treatment; ⁵ Certain soil mixes can leach P. Source: see [1]

Tree trenches are a system of trees that are connected by an underground infiltration structure. The system consists of a stormwater tree trench or box lined with geotextile fabric with structural stone, gravel or soil boxes in which the trees are placed. Tree systems consist of an engineered soil or rock layer designed to treat stormwater runoff via filtration through plant and soil/rock media, and through evapotranspiration from trees. Discharge of this stored runoff occurs through infiltration into the surrounding naturally permeable soil. Tree species are carefully selected to survive both inundation and drought conditions in urban environments where they will be potentially affected by chloride and other traffic concerns. Tree trenches and boxes drainage areas should be less than five acres depending on the size of each trench. Irrigation, whether manual or automated, is strongly encouraged during the tree’s establishment period.

For more information, see the following pages in this Manual.

Trees - general

Tree boxes/tree trenches

Dry swale with check dams

Dry swale with impermeable concrete check dams. Photo courtesy Limnotech.

Applications and treatment capabilities for dry swale with check dams
Applications		Treatment capabilities^{2, 3}
Residential	Yes	TSS	High⁴
Commercial	Yes	TN	Low/Medium
Ultra-urban	Limited⁶	TP	Low/Medium⁵
Industrial	Yes¹	Chloride	Low
Highway/road	Yes	Metals	High
Recreational	Yes	Oils and grease	High
		Pathogens	Medium
¹ Unless the infiltration practice is located in an industrial area with exposed significant materials or from vehicle fuelling and maintenance areas. Infiltration BMPs are PROHIBITED in these areas; ² This is only for the portion of flow that enters the infiltration basin; by-passed runoff does not receive treatment; ³ Low = < 30%; Medium = 30-65%; High = 65 -100%); ⁴ Assumes adequate pre-treatment; ⁵ Certain soil mixes can leach P; ⁶ Due to a size restriction. Source: see [2]

Similar to vegetated swales designed for stormwater conveyance, dry swales with check dams are designed as linear, multi-celled stormwater infiltration BMP’s. By incorporating earthen or structural check dams, runoff is retained and infiltrated along a series of narrow, shallow basins or cells. Coarse vegetation such as decorative plantings or even turf grass slow runoff movement. This system is designed to move, store, and infiltrate runoff from impervious surfaces such as linear roadways or parking lots. Dry swales are best designed for sites under one acre in size.

For more information see the following sections in the Minnesota Stormwater Manual.

High gradient stormwater step-pool swale with check dams

Step pool with impermeable check dam. Courtesy of Limnotech.

Applications and treatment capabilities for step pool with check dams
Applications		Treatment capabilities^{3, 4}
Residential	Yes	TSS	Medium⁵
Commercial	Yes	TN	Low
Ultra-urban	Limited¹	TP	Medium⁶
Industrial	Yes²	Chloride	Low
Highway/road	Yes	Metals	Medium
Recreational	Yes	Oils and grease	Low
		Pathogens	Low
¹ Due to size restriction; ² Unless the infiltration practice is located in an industrial area with exposed significant materials or from vehicle fuelling and maintenance areas. Infiltration BMPs are PROHIBITED in these areas; ³ This is only for the portion of flow that enters the infiltration basin; by-passed runoff does not receive treatment; ⁴ Low = < 30%; Medium = 30-65%; High = 65 -100%); ⁵ Assumes adequate pre-treatment; ⁶ Certain soil mixes can leach P. Source: see [3]

Stormwater step pools are defined by its design features that address higher energy flows due to more dramatic slopes than dry or wet swales. Using a series of pools, riffle grade control, native vegetation and a sand seepage filter bed, flow velocities are reduced, treated, and, where applicable, infiltrated. to shallow groundwater. The physical characteristics of the stormwater step pools are similar to Rosgen A or B stream classification types, where “bedform occurs as a step/pool, cascading channel which often stores large amounts of sediment in the pools associated with debris dams” (Rosgen, 1996). These structures feature surface/subsurface runoff storage seams and an energy dissipation design that is aimed at attenuating the flow to a desired level through energy and hydraulic power equivalency principles (Anne Arundel County, 2009). Stormwater step pools are designed with a wide variety of native plant species depending on the hydraulic conditions and expected post-flow soil moisture at any given point within the stormwater step pool.

For more information see the following sections in the Minnesota Stormwater Manual.

Non-structural infiltration practices

The vegetated filter strip in this photo is pretreatment for a bioswale. Photo courtesy of Alisha Goldstein, U.S. EPA.

The practices briefly described in this section are not considered infiltration structures because they do not capture a design volume of water and infiltrate that water at the point of capture. These practices can result in significant volumes of water being infiltrated, however.

Harvest and use/reuse systems

A stormwater harvest and reuse system is a constructed system that captures and retains stormwater for beneficial use at a different time or place than when or where the stormwater was generated. The most common use of retained water is irrigation, but captured water may be used for other purposes, such as indoor toilet flushing. The volume of water potentially infiltrated is a function of the storage capacity of the system. Volumes are restricted to relatively small amounts when tanks are used for storage. Tank storage is commonly used in more urban areas where surface space is restricted. If constructed ponds or wetlands are used for storage, significant volumes of water can be infiltrated through irrigation.

For more information, see the following sections.

Vegetated filter strips

Vegetated filter strips are vegetated areas where stormwater runoff can be directed. As water flows over the filter strip, some infiltration can occur. Infiltration is enhanced by the following conditions.

Coarse-textured soils
Native perennial vegetation
Increased surface roughness
Decreased land slope
Spreading the runoff over a larger area

For more information see Overview for pretreatment vegetated filter strips and Design, construction, operation and maintenance specifications for pretreatment vegetated filter strips.

Enhanced turf

Infiltration can be enhanced on soils that have been improved or amended. This manual contains limited information on enhanced turf and does not provide guidance for design, construction, maintenance, and assessment of enhanced turf. Information on use of compost in soil and credits associated with improved turf can be found on the Turf page. A discussion of alleviating compaction from construction activities can be found here.

Information: alert-danger

Swales with no check dams

Similar to vegetated filter strips, water can infiltrate into soils underlying swales. The amount of infiltration is typically very low, but can be enhanced by employing the same practices that enhance infiltration in vegetated filter strips.

Unit processes for different infiltration BMPs

The following table provides a summary of unit processes for the different infiltration BMPs.

Unit processes of stormwater treatment techniques (Adapted from WEF, 2008)
Link to this table

Control	Infiltration basin	Infiltration trench	Bioinfiltration	Permeable pavement	Tree box/tree trench	Enhanced turf
Peak flow attenuation	X	X	X	X
Runoff volume reduction	X	X	X	X	X
Infiltration	X	X	X	X	X	X
Dispersion
Evapotranspiration			X		X
Runoff collection and usage			X¹	X¹
Sedimentation	X	X	X
Flotation	X		X
Laminar separation
Swirl concentration
Sorption	X	X	X	X
Precipitation	X	X	X	X
Coagulation	X	X	X	X
Filtration			X
Plant metabolism			X		X	X
Nitrification/denitrification	X	X	X
Organic compound degradation	X	X	X	X
Pathogen die off	X	X		X
Temperature reduction	X	X	X	X
Disinfection	X	X	X	X

¹ If underdrain is present

Information tables

The following tables describe and differentiate different characteristics of stormwater infiltration BMPs.

Overview table

The following table provides a brief description and schematic of each stormwater infiltration BMP.

Stormwater infiltration BMPs - overview
Link to this table

Stormwater BMP	General Overview	Illustration
Infiltration Basin	A natural or constructed impoundment that captures, temporarily stores and infiltrates the design volume of water into the surrounding naturally permeable soil over several days. In the case of a constructed basin, the impoundment is created by excavation or embankment.
Bioinfiltration Basin	Often called rain gardens, bioinfiltration basins use engineered or mixed soils and plantings to capture and infiltrate runoff. Pollutants are removed using highly permeable soils that are able to draw the basin down in less than 48 hours.
Infiltration Trench Synonym: Infiltration Gallery	A shallow excavated trench that is backfilled with a coarse stone aggregate allowing for the temporary storage of runoff in the void space of the material. Discharge of this stored runoff occurs through infiltration into the surrounding naturally permeable soil.
Dry Well Synonym: Infiltration Tube, French Drain, Soak‐Away Pits, Soak Holes	A smaller variation of an infiltration trench. It is a subsurface storage facility (a structural chamber or an excavated pit backfilled with a coarse stone aggregate) that receives and temporarily stores stormwater runoff. Discharge of this stored runoff occurs through infiltration into the surrounding naturally permeable soil. Due to their size, dry wells are typically designed to handle stormwater runoff from smaller drainage areas.
Underground Infiltration	Several underground infiltration systems, including pre‐manufactured pipes, vaults, and modular structures, have been developed as alternatives to infiltration basins and trenches for space‐limited sites and stormwater retrofit applications. These systems are similar to infiltration basins and trenches in that they are designed to capture, temporarily store and infiltrate the design volume of stormwater over several days. Discharge of this stored runoff occurs through infiltration into the surrounding naturally permeable soil.
Dry Swale with Check Dams	Similar to vegetated swales designed for stormwater conveyance, dry swales with check dams are designed as linear, multi‐celled stormwater infiltration BMPs. By incorporating earthen, structural or rock check dams, runoff is retained and infiltrated along a series of narrow, shallow basins or cells. Coarse vegetation such as decorative plantings or even turf grass slow runoff movement. This system is designed to move, store, and infiltrate runoff from impervious surfaces such as linear roadways or parking lots.
Permeable Pavement	Permeable pavements are paving surfaces that allow stormwater runoff to filter through surface voids into an underlying stone reservoir for infiltration and/or storage. The most commonly used permeable pavement surfaces are pervious concrete, porous asphalt, and permeable interlocking concrete pavers (PICP). All permeable pavements have a similar structure, consisting of a surface pavement layer, an underlying stone aggregate reservoir layer, optional underdrains and geotextile over uncompacted soil subgrade. Discharge of this stored runoff occurs through infiltration into the surrounding naturally permeable soil.
Tree Trench/Tree Box	A system of trees that are connected by an underground infiltration structure. The system consists of a trench lined with geotextile fabric with structural stone, gravel or soil boxes in which the trees are placed. Tree systems consist of an engineered soil layer designed to treat stormwater runoff via filtration through plant and soil media, and through evapotranspiration from trees. Discharge of this stored runoff occurs through infiltration into the surrounding naturally permeable soil.

Contributing drainage area table

The following table provides a summary of recommended contributing drainage area for each stormwater infiltration BMP.

Contributing drainage area is defined as the total area, including pervious and impervious surfaces, contributing to a best management practice (BMP). It is assumed that in most cases, with the exception of green roofs and many permeable pavement systems, impervious surfaces will constitute more than 50 percent of the contributing area to the BMP and that most of this impervious is directly connected impervious. The recommended contributing area to a BMP may be modified for the following conditions.

The recommended contributing area may be increased if pervious surfaces constitute the majority of the contributing area and soils are hydrologic soil group (HSG) A or B
The recommended contributing area should be decreased if impervious surfaces contribute more than 80 percent of the contributing area or if the entire impervious surface is directly connected and routed to the BMP
The recommended contributing area should be decreased or may be increased based on pollutant loading (decrease with higher pollutant loads)

Runoff coefficients may be calculated for an area contributing to a BMP. Runoff coefficients greater than about 0.55 are typical of urban areas having 50 percent or more impervious surface. Typical runoff coefficients are shown on these pages ([4], [5]) and discussed here. To see how runoff curve number is associated with impervious percentages, see at this link.

Stormwater infiltration BMPs - contributing drainage area
Link to this table

Stormwater BMP	Recommended contributing area	Notes
Infiltration Basin	50 acres or less	A natural or constructed impoundment that captures, temporarily stores and infiltrates the design volume of water into the surrounding naturally permeable soil over several days. In the case of a constructed basin, the impoundment is created by excavation or embankment.
Bioinfiltration Basin	5 acres or less	Bioinfiltration basins must meet the required 48 hour drawdown time and must be sized in order to allow for adequate maintenance. It is HIGHLY RECOMMENDED that bioinfiltration basins be designed to prevent high levels of bounce as submerging vegetation may inhibit plant growth. A maximum wet storage depth of 1.5 feet is HIGHLY RECOMMENDED.
Infiltration Trench	5 acres or less
Dry Well Synonym: Infiltration Tube, French Drain, Soak‐Away Pits, Soak Holes	1 acre or less (rooftop only)
Underground Infiltration	10 acres or less	Though feasible, larger underground infiltration systems may cause groundwater contamination as water is not able to infiltrate through a surface cover. In addition, wind flocculation, UV degradation, and bacterial degradation, which provide additional treatment in surface systems, do not occur in underground systems. Because performance research is lacking for larger features, it is HIGHLY RECOMMENDED that the contributing drainage area to a single device not exceed 10 acres.
Dry Swale with Check Dams	5 acres or less
Permeable Pavement	It is RECOMMENDED that external contributing drainage area not exceed the surface area of the permeable pavement. It is HIGHLY RECOMMENDED that external contributing drainage area not exceed twice the surface area of the permeable pavement	It is RECOMMENDED that external drainage area be as close to 100% impervious as possible. Field experience has shown that drainage area (pervious or impervious) can contribute particulates to the permeable pavement and lead to clogging. Therefore, sediment source control and/or pretreatment should be used to control sediment run-on to the permeable pavement section.
Tree Trench/Tree Box	up to 0.25 acres per tree

References: Virginia, North Carolina, West Virginia, Maine, Lake Tahoe, Connecticut, Massachusetts, New York, Wisconsin, Vermont, New Hampshire, Ontario, Pennsylvania

Treatment properties table

The following table provides information on pollutant removal mechanism(s), location in the stormwater treatment train, general pollutant removal, and potential applications for each of the stormwater BMPs.

Stormwater infiltration BMPs - treatment properties
Link to this table

Stormwater BMP	Pollutant Removal Mechanism	Location in Treatment Train	Pollutant Removal ^1,2	Potential Application ¹
Infiltration Basin	Sedimentation / Infiltration	End	TSS: High TN: Medium/High TP: Medium/High Chloride: Low Metals: High Oils and Grease: High Pathogens: High	Residential: Yes Commercial: Yes Ultra Urban: Limited Industrial: Limited Retrofit: Yes Highway/Road: Limited
Bioinfiltration Basin	Sedimentation / Infiltration	Beginning	TSS: High TN: Low/Medium TP: Medium/High Chloride: Low Metals: High Oils and Grease: High	Residential: Yes Commercial: Yes Ultra Urban: Limited Industrial: Limited Retrofit: Yes Highway/Road: Limited
Infiltration Trench Synonym: Infiltration Gallery	Infiltration	nd	TSS: High TN: Medium/High TP: Medium/High Chloride: Low Metals: High Oils and Grease: High Pathogens: High	Residential: Yes Commercial: Yes Ultra Urban: Yes Industrial: Limited Retrofit: Yes Highway/Road: Yes
Dry Well Synonym: Infiltration Tube, French Drain, Soak‐Away Pits, Soak Holes	Infiltration	throughout	TSS: High TN: Medium/High TP: Medium/High Chloride: Low Metals: High Oils and Grease: High Pathogens: High	Residential: Yes Commercial: Yes Ultra Urban: Yes Industrial: Limited Retrofit: Yes Highway/Road: No
Underground Infiltration	Sedimentation / Infiltration / Flotation/Skimming	End	TSS: High TN: Medium/High TP: Medium/High Chloride: Low Metals: High Oils and Grease: High Pathogens: High	Residential: Yes Commercial: Yes Ultra Urban: Yes Industrial: Limited Retrofit: Yes Highway/Road: Limited
Dry Swale with Check Dams	Sedimentation / Infiltration	Throughout	TSS: High TN: Low/Medium TP: Low/Medium Chloride: Low Metals: High Oils and Grease: High Pathogens: Medium	Residential: Yes Commercial: Yes Ultra Urban: Limited Industrial: Yes Retrofit: Limited Highway/Road: Yes
Permeable Pavement	Infiltration	Beginning	TSS: High TN: Medium/High TP: Medium/High Chloride: Low Metals: High Oils and Grease: High	Residential: Yes Commercial: Yes Ultra Urban: Yes Industrial: Limited Retrofit: Yes Highway/Road: Limited
Tree Trench/Tree Box	Infiltration, Transpiration	Throughout	TSS: High TN: Medium/High TP: Medium/High Chloride: Low Metals: High Oils and Grease: High Pathogens: High	Residential: Limited Commercial: Yes Ultra Urban: Yes Industrial: Limited Retrofit: Yes Highway/Road: Limited

¹ Treatment Capabilities and Potential Applications referenced from Manual Section BMP's for stormwater infiltration
² Low = < 30%; Medium = 30‐65%; High = 65‐100%

Selection considerations table

The following table provides information on general cost, maintenance requirements, pretreatment needs, and habitat quality for each of the stormwater infiltration BMPs.

Stormwater infiltration BMPs – selection considerations
Link to this table

Stormwater BMP	Cost	Maintenance Requirements ³	Pre‐treatment ⁴	Habitat Quality ⁵
Infiltration Basin	Low $0.5‐$1.3 CF	Simple‐Intensive	Needed Oil/Water Separator, Vegetated Filter, Sediment Basin, Water Quality Inlets	Low
Bioinfiltration Basin	Low $0.5‐$1.3 CF	Simple‐Intensive	Needed Oil/Water Separator, Vegetated Filter, Sediment Basin, Water Quality Inlets	Medium‐High
Infiltration Trench Synonym: Infiltration Gallery	Low $1‐$4 CF	Medium	Needed Oil/Water Separator, Vegetated Filter, Sediment Basin, Water Quality Inlets	None
Dry Well Synonym: Infiltration Tube, French Drain, Soak‐Away Pits, Soak Holes	Low $1‐$4 CF	Medium	Needed Oil/Water Separator, Vegetated Filter, Water Quality Inlets	None
Underground Infiltration	High 14 CF	Medium	Needed Oil/Water Separator, Water Quality Inlets	None
Dry Swale with Check Dams	Low $.5‐$1.3 CF	Simple‐Medium	Needed Vegetated Filter, Water Quality Inlets	Low‐Medium
Permeable Pavement	Medium 3‐10 CF	Medium	No Pretreatment Required	None
Tree Trench/Tree Box	High $1.80 ‐ $12.70 CF based on recommended soil volume of 1,414 CF per tree	Intensive	Needed Oil/Water Separator, Water Quality Inlets	Medium

¹ Maintenance requirements to be addressed and updated in future section
² Pretreatment requirements to be revised as per updated section
³ Habitat quality refers to the possible diversity of plantings commonly installed with each BMP

See Infiltration Summary Table

To see all information contained in the previous tables in a single table, click on the following link: Infiltration Summary Table

Related pages for stormwater infiltration

Related pages for infiltration BMPs

@@ Line 1: / Line 1: @@
-Best Management Practices that infiltrate stormwater runoff into underlying soil include, but are not limited, to
+{{alert|Infiltration practices can be an important tool for retention and detention of stormwater runoff and treatment of pollutants in stormwater runoff. If the practice utilizes vegetation, additional benefits may include cleaner air, carbon sequestration, improved biological habitat, and aesthetic value.|alert-success}}
-*infiltration basins,
+{{alert|Infiltration of stormwater, where appropriate, is a preferred practice for managing stormwater runoff, as it reduces pollutants reaching receiving waters and retains water on the landscape|alert-success}}
+[[File:Pdf image.png|100px|thumb|alt=pdf image|<font size=3>[https://stormwater.pca.state.mn.us/index.php?title=File:BMPs_for_stormwater_infiltration_-_Minnesota_Stormwater_Manual.pdf Download pdf]</font size>]]
+[[File:General information page image.png|right|100px|alt=image]]
+<span title="One of many different structural or non–structural methods used to treat runoff"> '''Best management practices'''</span> that <span title="Infiltration Best Management Practices (BMPs) treat urban stormwater runoff as it flows through a filtering medium and into underlying soil, where it may eventually percolate into groundwater. The filtering media is typically coarse-textured and may contain organic material, as in the case of bioinfiltration BMPs."> [https://stormwater.pca.state.mn.us/index.php?title=Stormwater_infiltration_Best_Management_Practices '''infiltrate''']</span> stormwater runoff into underlying soil include, but are not limited, to
+*<span title="Infiltration basins, infiltration trenches, dry wells, and underground infiltration systems capture and temporarily store stormwater before allowing it to infiltrate into the soil. As the stormwater penetrates the underlying soil, chemical, biological and physical processes remove pollutants and delay peak stormwater flows."> [https://stormwater.pca.state.mn.us/index.php?title=Infiltration '''infiltration basins''']</span>,
 *infiltration trenches (includes dry wells),
 *underground infiltration systems,
-*bioinfiltration,
+*<span title="A bioretention practice in which no underdrain is used. All water entering the bioinfiltration practice infiltrates or evapotranspires."> '''bioinfiltration'''</span>,
-*permeable pavements,
+*<span title="Permeable pavements allow stormwater runoff to filter through surface voids into an underlying stone reservoir for temporary storage and/or infiltration. The most commonly used permeable pavement surfaces are pervious concrete, porous asphalt, and permeable interlocking concrete pavers (PICP)."> '''[https://stormwater.pca.state.mn.us/index.php?title=Permeable_pavement permeable pavements]'''</span>,
-*tree trenches and tree boxes, and
+*<span title="A tree trench, often known as a "vertical rain garden," is a system that consists of piping for water storage, structural soils and a tree."> '''[https://stormwater.pca.state.mn.us/index.php?title=Trees tree trenches]'''</span> and <span Title="Tree box filters are widely deployed as stormwater treatment BMPs, normally in stand-alone applications, however can also be used as pretreatment for infiltration, rainwater harvesting, and detention."> '''tree boxes'''</span>, and
-*dry swale with check dams.
+*<span title="Dry swales, sometimes called grass swales, are similar to bioretention cells but are configured as shallow, linear channels. They typically have vegetative cover such as turf or native perennial grasses. Dry swales may be constructed as filtration or infiltration practices, depending on soils."> [https://stormwater.pca.state.mn.us/index.php?title=Dry_swale_(Grass_swale) '''dry swale''']</span> with <span title="A check dam is a structure installed perpendicular to flow in a natural or manmade conveyance channel to reduce flow velocity. By slowing flow velocities, check dams can serve multiple functions including reduction of channel scour and erosion, enhancement of sediment trapping, and greater treatment of the water quality control volume via enhanced water detention or retention. Typical check dam materials include rock, earth, wood, and concrete. "> '''check dams'''</span>.
 These are discussed briefly below. Additional information about these BMPs can be found in the following tables.
@@ Line 12: / Line 19: @@
 *[http://stormwater.pca.state.mn.us/index.php/Stormwater_infiltration_BMPs_%E2%80%93_selection_considerations Stormwater infiltration BMPs – selection considerations]
 *[http://stormwater.pca.state.mn.us/index.php/Stormwater_infiltration_BMPs_-_treatment_properties Stormwater infiltration BMPs - treatment properties]
+{{alert|Note that other practices may infiltrate water but are not specifically designed to infiltrate water at the point where water is detained. Examples include [[Stormwater and rainwater harvest and use/reuse|stormwater harvest and reuse systems]], [[Overview for pretreatment vegetated filter strips|vegetated filter strips]] and swales without check dams.|alert-info}}
 ==Infiltration basin==
@@ Line 62: / Line 71: @@
 |}
-An infiltration basin is a natural or constructed impoundment that captures, temporarily stores and infiltrates the design volume of water. Drawdown of this stored runoff occurs through infiltration into the surrounding naturally permeable soil. The required drawdown time is 48 hours or less. Water that is stored but not infiltrated must leave the BMP, typically through an outlet, within the required drawdown time. In the case of a constructed basin, the impoundment is created by excavation or embankment. Infiltration basins are commonly used for drainage areas of 5 to 50 acres with land slopes that are less than 20 percent. Typical depths range from 2 to 6 feet, including bounce in the basin. The sizing is to control stormwater volumes at the regional or development scale as opposed to bioretention basins (rain gardens) that are designed at the site scale. Typical dimensions range from 1,000 square feet up to an acre. Infiltration basins are commonly constructed with plant species that can tolerate and thrive in this unique growing environment.
+An infiltration basin is a natural or constructed impoundment that captures, temporarily stores and infiltrates the design volume of water (<span title="The volume of water that is treated by a BMP."> [https://stormwater.pca.state.mn.us/index.php?title=Water_quality_criteria '''Water Quality Volume''']</span>). <span title="The length of time, usually expressed in hours, for ponded water in a stormwater practice to drain. For stormwater practices where water is stored in media, there is no clear definition of drawdown, but an acceptable assumption is the time for water to drain to field capacity"> '''Drawdown'''</span> of this stored runoff occurs through infiltration into the surrounding naturally permeable soil. The required <span title="The length of time, usually expressed in hours, for ponded water in a stormwater practice to drain. For stormwater practices where water is stored in media, there is no clear definition of drawdown, but an acceptable assumption is the time for water to drain to field capacity"> '''drawdown time'''</span> is 48 hours or less. Water that is stored but not infiltrated must leave the bmp, typically through an outlet, within the required drawdown time. In the case of a constructed basin, the impoundment is created by excavation or embankment. Infiltration basins are commonly used for drainage areas of 5 to 50 acres with land slopes that are less than 20 percent. Typical depths range from 2 to 6 feet, including <span title="Water level fluctuations due to topography, soils, and runoff inputs during and after precipitation events."> [https://stormwater.pca.state.mn.us/index.php?title=File:Drawdown_and_bounce_2.jpg '''bounce''']</span> in the basin. The <span title="Sizing refers to the physical dimensions of a stormwater treatment practice or device needed to meet a water quality or quantity goal. For example, stormwater BMPs may be sized to treat a volume of runoff, a flow rate, or to meet a pollutant removal target."> '''sizing'''</span> is to control stormwater volumes at the regional or development scale as opposed to bioretention basins (rain gardens) that are designed at the site scale. Typical dimensions range from 1,000 square feet up to an acre. Infiltration basins are commonly constructed with plant species that can tolerate and thrive in this unique growing environment.
 For more information, see the following pages in this Manual.
@@ Line 131: / Line 140: @@
 For more information, see the following pages in this Manual.
-*[[Overview for Infiltration trench]]
+*[[Overview for infiltration]]
-*[[Design criteria for Infiltration trench]]
+*[[Design criteria for infiltration]]
-*[[Construction specifications for Infiltration trench]]
+*[[Construction specifications for infiltration]]
-*[[Operation and maintenance of Infiltration trench]]
+*[[Operation and maintenance of stormwater infiltration practices]]
-*[[Cost-benefit considerations for Infiltration trench]]
+*[[Cost-benefit considerations for infiltration]]
-*[[Calculating credits for infiltration trench]]
+*[[Calculating credits for infiltration]]
-*[[External resources for Infiltration trench]]
+*[[External resources for infiltration]]
-*[[References for Infiltration trench]]
+*[[References for infiltration]]
 *[[Requirements, recommendations and information for using infiltration basin/underground infiltration BMPs in the MIDS calculator]]
 ===Dry wells (a.k.a. infiltration tubes, french drains, soak-away pits or soak holes)===
 A dry well or soak away pit is a smaller variation of an infiltration trench. It is a subsurface storage facility (a structural chamber or an excavated pit backfilled with a coarse stone aggregate) that receives and temporarily stores stormwater runoff. Discharge of this stored runoff occurs through infiltration into the surrounding naturally permeable soil. Due to their size, dry wells are typically designed to handle stormwater runoff from smaller drainage areas, less than one acre in size (e.g. roof tops).
+For more information, see the following pages in this Manual.
+*[[Overview for infiltration]]
+*[[Design criteria for infiltration]]
+*[[Construction specifications for infiltration]]
+*[[Operation and maintenance of stormwater infiltration practices]]
+*[[Cost-benefit considerations for infiltration]]
+*[[Calculating credits for infiltration]]
+*[[External resources for infiltration]]
+*[[References for infiltration]]
+*[[Requirements, recommendations and information for using infiltration basin/underground infiltration BMPs in the MIDS calculator]]
 ===Underground infiltration systems===
-Several underground infiltration systems, including pre-manufactured pipes, vaults, and modular structures, have been developed as alternatives to infiltration basins and trenches for space-limited sites and stormwater retrofit applications. Underground infiltration systems are occasionally the only stormwater BMP options on fully developed sites as they can be located under other land uses such as parking lots or play areas. These systems are similar to infiltration basins and trenches in that they are designed to capture, temporarily store and infiltrate the design volume of stormwater over several days. Underground infiltration systems are generally applicable to small development sites (typically less than 10 acres) and should be installed in areas that are easily accessible to routine and non-routine maintenance. These systems should not be located in areas or below structures that cannot be excavated in the event that the system needs to be replaced or invasive maintenance is required to maintain performance.
+[[File:Contech infiltration system in native sandy soils.png |right|thumb|300 px|alt=This picture shows an infiltration system in native sandy soils|<font size=3>Underground TrueNorthSteel infiltration system in native sandy soils</font size>]]
-Underground infiltration systems and dry wells have been installed below parking lots and other impervious surfaces on sites where insufficient space exists for a surface infiltration system.  They are designed to temporarily store stormwater runoff before slowly infiltrating the water into the subsurface ([[References_for_stormwater_infiltration#C|Connecticut, 2004]]).  There is limited information on the effectiveness of these systems in removing pollutants. Limited data suggests they may be less effective at removing mobile pollutants than surface-based infiltration systems.
+Several underground infiltration systems, including pre-manufactured pipes, vaults, and modular structures, have been developed as alternatives to infiltration basins and trenches for space-limited sites and stormwater retrofit applications. Underground infiltration systems are occasionally the only stormwater BMP options on fully developed sites or <span title="Highly urban and ultra-urban settings have a large percentage of impermeable surface and typically have limited space to install surface BMPs. An example would be a downtown area."> '''highly urban and ultra-urban environments'''</span> as they can be located under other land uses such as parking lots or play areas. These systems are similar to infiltration basins and trenches in that they are designed to capture, temporarily store and infiltrate the design volume of stormwater over several days. Underground infiltration systems are generally applicable to small development sites (typically less than 10 acres) and should be installed in areas that are easily accessible to routine and non-routine maintenance. These systems should not be located in areas or below structures that cannot be excavated in the event that the system needs to be replaced or invasive maintenance is required to maintain performance.
+Underground infiltration systems and dry wells have been installed below parking lots and other impervious surfaces on sites where insufficient space exists for a surface infiltration system.  They are designed to temporarily store stormwater runoff before slowly infiltrating the water into the subsurface ([[References_for_stormwater_infiltration#C|Connecticut, 2004]]).  There is limited information on the effectiveness of these systems in removing pollutants.
 One concern is that underground infiltration may meet the U.S. Environmental Protection Agency (EPA) definition of a [http://water.epa.gov/type/groundwater/uic/class5/index.cfm Class V injection well]. Class V injection wells are defined as any bored, drilled, or driven shaft, or any dug hole that is deeper than its widest surface dimension. Class V injection wells can also be an improved sinkhole, or a subsurface fluid distribution system (from U.S. EPA, June 2003).  The U.S. EPA administers Class V injection well permits in Minnesota.  Minimum requirements for installing, permitting, and operating a Class V well is defined by the [http://water.epa.gov/type/groundwater/uic/class5/index.cfm USEPA].
-A second concern pertains to the overall pollutant removal effectiveness of those underground infiltration systems that do not meet the definition of a Class V injection well.   The document released by the Transport Research Synthesis titled [http://www.lrrb.org/media/reports/TRS0903.pdf “Issues of Concern Related to Underground Infiltration Systems for Stormwater Management and Treatment”] provides a good overview of the concerns related to underground infiltration systems (MNDOT, 2009).  Issues identified in this report include:
+A second concern pertains to the overall pollutant removal effectiveness of those underground infiltration systems that do not meet the definition of a Class V injection well.   The document released by the Transport Research Synthesis titled [http://www.lrrb.org/media/reports/TRS0903.pdf “Issues of Concern Related to Underground Infiltration Systems for Stormwater Management and Treatment”] provides a good overview of the concerns related to underground infiltration systems (MNDOT, 2009).  Issues identified in this report include the following.
 * There is potential that an underground infiltration system meets the criteria of a Class V injection well.
 * There is insufficient knowledge of the fate of pollutants in the subgrade below the buried infiltration systems.
@@ Line 158: / Line 181: @@
 * The minimum separation requirement of 3 feet between the bottom of the infiltration system and the seasonally high groundwater elevation may be insufficient for adequate pollutant removal.  Additional study is recommended.
 * Maintenance of underground systems is critical for effective pollutant removal.  However, access for maintenance is challenging.  There are concerns that the difficult access is preventing owners from properly maintaining these systems.
+For more information, see the following pages in this Manual.
+*[[Overview for infiltration]]
+*[[Design criteria for infiltration]]
+*[[Construction specifications for infiltration]]
+*[[Operation and maintenance of stormwater infiltration practices]]
+*[[Cost-benefit considerations for infiltration]]
+*[[Calculating credits for infiltration]]
+*[[External resources for infiltration]]
+*[[References for infiltration]]
+*[[Requirements, recommendations and information for using infiltration basin/underground infiltration BMPs in the MIDS calculator]]
 ==Bioinfiltration basin==
@@ Line 209: / Line 244: @@
 |}
-Bioinfiltration basins, often called rain gardens, use soil (typically engineered media or mixed soil) and native vegetation to capture runoff and remove pollutants. Both the media and underlying soil typically have high infiltration rates that allow captured water to infiltrate within a required drawdown time, usually 48 hours. For more information, see the following pages in this Manual.
+Bioinfiltration basins, often called rain gardens, use soil (typically <span title="Engineered media is a mixture of sand, fines (silt, clay), and organic matter utilized in stormwater practices, most frequently in bioretention practices. The media is typically designed to have a rapid infiltration rate, attenuate pollutants, and allow for plant growth."> [https://stormwater.pca.state.mn.us/index.php?title=Design_criteria_for_bioretention#Materials_specifications_-_filter_media '''engineered media''']</span> or mixed soil) and native vegetation to capture runoff and remove pollutants. Both the media and underlying soil typically have high infiltration rates that allow captured water to infiltrate within a required drawdown time, usually 48 hours. Bioinfiltration systems, which lack an <span title="An underground drain or trench with openings through which the water may percolate from the soil or ground above"> '''underdrain'''</span> and are designed for infiltration, differ from biofiltration systems, which have an underdrain and are designed primarily for filtration. For more information, see the following pages in this Manual.
 *[[Bioretention terminology]] (including types of bioretention)
@@ Line 346: / Line 381: @@
 |}
-Tree trenches are a system of trees that are connected by an underground infiltration structure. The system consists of a stormwater tree trench or box lined with geotextile fabric with structural stone, gravel or soil boxes in which the trees are placed. Tree systems consist of an engineered soil or rock layer designed to treat stormwater runoff via filtration through plant and soil/rock media, and through evapotranspiration from trees. Discharge of this stored runoff occurs through infiltration into the surrounding naturally permeable soil. Tree species are carefully selected to survive both inundation and drought conditions in urban environments where they will be potentially affected by chloride and other traffic concerns. Tree trenches and boxes drainage areas should be less than five acres depending on the size of each trench. Irrigation, whether manual or automated, is strongly encouraged during the tree’s establishment period.
+Tree trenches are a system of trees that are connected by an underground infiltration structure. The system consists of a stormwater tree trench or box lined with geotextile fabric with structural stone, gravel or soil boxes in which the trees are placed. Tree systems consist of an engineered soil or rock layer designed to treat stormwater runoff via filtration through plant and soil/rock media, and through <span title="Loss of water to the atmosphere as a result of the joint processes of evaporation and transpiration through vegetation"> '''evapotranspiration'''</span> from trees. Discharge of this stored runoff occurs through infiltration into the surrounding naturally permeable soil. Tree species are carefully selected to survive both inundation and drought conditions in urban environments where they will be potentially affected by chloride and other traffic concerns. Tree trenches and boxes drainage areas should be less than five acres depending on the size of each trench. Irrigation, whether manual or automated, is strongly encouraged during the tree’s establishment period.
 For more information, see the following pages in this Manual.
@@ Line 370: / Line 405: @@
 ==Dry swale with check dams==
+[[File:Concrete check dams.jpg|300px|thumb|left|alt=photo concrete check dams|<font size=3>Dry swale with impermeable concrete check dams. Photo courtesy Limnotech.</font size>]]
 {| class="wikitable" style="float:right; margin-left: 10px; width:500px;"
@@ Line 389: / Line 425: @@
 |-
 | Ultra-urban
-| Limited
+| Limited<sup>6</sup>
 | TP
 | Low/Medium<sup>5</sup>
@@ Line 413: / Line 449: @@
 | Medium
 |-
-| colspan="4" style="text-align: center;" | <font size=1><sup>1</sup> Unless the infiltration practice is located in an industrial area with exposed significant materials or from vehicle fuelling and maintenance areas. Infiltration BMPs are PROHIBITED in these areas; <sup>2</sup> This is only for the portion of flow that enters the infiltration basin; by-passed runoff does not receive treatment; <sup>3</sup> Low = < 30%; Medium = 30-65%; High = 65 -100%); <sup>4</sup> Assumes adequate pre-treatment; <sup>5</sup> Certain [http://stormwater.pca.state.mn.us/index.php/Design_criteria_for_bioretention#Materials_specifications_-_filter_media soil mixes] can leach P.<br>
+| colspan="4" style="text-align: center;" | <font size=1><sup>1</sup> Unless the infiltration practice is located in an industrial area with exposed significant materials or from vehicle fuelling and maintenance areas. Infiltration BMPs are PROHIBITED in these areas; <sup>2</sup> This is only for the portion of flow that enters the infiltration basin; by-passed runoff does not receive treatment; <sup>3</sup> Low = < 30%; Medium = 30-65%; High = 65 -100%); <sup>4</sup> Assumes adequate pre-treatment; <sup>5</sup> Certain [http://stormwater.pca.state.mn.us/index.php/Design_criteria_for_bioretention#Materials_specifications_-_filter_media soil mixes] can leach P; <sup>6</sup> Due to a size restriction.<br>
 Source: see [http://stormwater.pca.state.mn.us/index.php/File:Trees_Tasks_2_and_13_Water_quality_benefits.docx]
 </font size>
@@ Line 421: / Line 457: @@
 surfaces such as linear roadways or parking lots. Dry swales are best designed for sites under one acre in size.
-==Enhanced turf==
+For more information see the following sections in the Minnesota Stormwater Manual.
-Infiltration can be enhanced on soils that have been improved or amended. This manual contains limited information on enhanced turf and does not provide guidance for design, construction, maintenance, and assessment of enhanced turf. Information on use of compost in soil and credits associated with improved turf can be found on the [[Turf]] page. A discussion of alleviating compaction from construction activities can be found [http://stormwater.pca.state.mn.us/index.php/Alleviating_compaction_from_construction_activities here].
+*[[Terminology for swales|Terminology for swales (grass channels)]]
+*[[Overview for dry swale (grass swale)]]
+*[[Design criteria for dry swale (grass swale)]]
+*[[Construction specifications for dry swale (grass swale)]]
+*[[Operation and maintenance of dry swale (grass swale)]]
+*[[Assessing the performance of dry swale (grass swale)]]
+*[[Calculating credits for dry swale (grass swale)]]
+*[[Cost considerations for dry swale (grass swale)]]
+*[[Case studies for dry swale (grass swale)]]
+*[[Plants for swales]]
+*[[Check dams for stormwater swales]]
+*[[External resources for swales|External resources for dry swale (grass swale)]]
+*[[References for dry swale (grass swale)]]
+*[https://stormwater.pca.state.mn.us/index.php?title=Requirements,_recommendations_and_information_for_using_swale_without_an_underdrain_as_a_BMP_in_the_MIDS_calculator Requirements, recommendations and information for using dry swale (grass swale) without an underdrain in the MIDS calculator]
+*[https://stormwater.pca.state.mn.us/index.php?title=Requirements,_recommendations_and_information_for_using_swale_with_an_underdrain_as_a_BMP_in_the_MIDS_calculator Requirements, recommendations and information for using dry swale (grass swale) with an underdrain in the MIDS calculator]
+*[[Requirements, recommendations and information for using swale side slope as a BMP in the MIDS calculator]]
-{{alert|Enhanced turf cannot be used to meet requirements of the [http://stormwater.pca.state.mn.us/index.php/III._STORMWATER_DISCHARGE_DESIGN_REQUIREMENTS#III.D._PERMANENT_STORMWATER_MANAGEMENT_SYSTEM Construction Stormwater General permit] because infiltrated water does not represent an instantaneous volume.|alert-danger}}
+==High gradient stormwater step-pool swale with check dams==
+[[File:4-stormwater-step-pool-LimnoTech.jpg|300px|thumb|left|alt=step pool photo|<font size=3>Step pool with impermeable check dam. Courtesy of Limnotech.</font size>]]
+{| class="wikitable" style="float:right; margin-left: 10px; width:500px;"
+|-
+| colspan="4" style="text-align: center;"| '''Applications and treatment capabilities for step pool with check dams'''
+|-
+| colspan="2" style="text-align: center;" | '''Applications'''
+| colspan="2" style="text-align: center;" | '''Treatment capabilities<sup>3, 4</sup>'''
+|-
+| Residential
+| Yes
+| TSS
+| Medium<sup>5</sup>
+|-
+| Commercial
+| Yes
+| TN
+| Low
+|-
+| Ultra-urban
+| Limited<sup>1</sup>
+| TP
+| Medium<sup>6</sup>
+|-
+| Industrial
+| Yes<sup>2</sup>
+| Chloride
+| Low
+|-
+| Highway/road
+| Yes
+| Metals
+| Medium
+|-
+| Recreational
+| Yes
+| Oils and grease
+| Low
+|-
+|
+|
+| Pathogens
+| Low
+|-
+| colspan="4" style="text-align: center;" | <font size=1><sup>1</sup> Due to size restriction; <sup>2</sup> Unless the infiltration practice is located in an industrial area with exposed significant materials or from vehicle fuelling and maintenance areas. Infiltration BMPs are PROHIBITED in these areas; <sup>3</sup> This is only for the portion of flow that enters the infiltration basin; by-passed runoff does not receive treatment; <sup>4</sup> Low = < 30%; Medium = 30-65%; High = 65 -100%); <sup>5</sup> Assumes adequate pre-treatment; <sup>6</sup> Certain [http://stormwater.pca.state.mn.us/index.php/Design_criteria_for_bioretention#Materials_specifications_-_filter_media soil mixes] can leach P.<br>
+Source: see [http://stormwater.pca.state.mn.us/index.php/File:Trees_Tasks_2_and_13_Water_quality_benefits.docx]
+</font size>
+|}
+Stormwater step pools are defined by its design features that address higher energy flows due to more dramatic slopes than dry or wet swales. Using a series of pools, riffle grade control, <span title="A species that has been observed in the form of a naturally occurring and self-sustaining population in historical times. Non-natives do not meet this definition."> '''native vegetation'''</span> and a sand seepage filter bed, flow velocities are reduced, treated, and, where applicable, infiltrated. to shallow groundwater. The physical characteristics of the stormwater step pools are similar to [https://cfpub.epa.gov/watertrain/moduleFrame.cfm?parent_object_id=1199 Rosgen A or B stream classification types], where “bedform occurs as a step/pool, cascading channel which often stores large amounts of sediment in the pools associated with debris dams” (Rosgen, 1996). These structures feature surface/subsurface runoff storage seams and an energy dissipation design that is aimed at attenuating the flow to a desired level through energy and hydraulic power equivalency principles (Anne Arundel County, 2009). Stormwater step pools are designed with a wide variety of native plant species depending on the hydraulic conditions and expected post-flow soil moisture at any given point within the stormwater step pool.
+For more information see the following sections in the Minnesota Stormwater Manual.
+*[[Terminology for swales|Terminology for high-gradient stormwater step-pool swale]]
+*[[Overview for high-gradient stormwater step-pool swale]]
+*[[Design criteria for high-gradient stormwater step-pool swale]]
+*[[Construction specifications for high-gradient stormwater step-pool swale]]
+*[[Operation and maintenance of high-gradient stormwater step-pool swale]]
+*[[Assessing the performance of high-gradient stormwater step-pool swale]]
+*[[Check dams for stormwater swales]]
+*[[Plants for swales]]
+*[[Calculating credits for high-gradient stormwater step-pool swale]]
+*[https://stormwater.pca.state.mn.us/index.php?title=Cost_considerations_for_dry_swale_(grass_swale) Cost considerations]
+*[[External resources for high-gradient stormwater step-pool swale]]
+*[[References for high-gradient stormwater step-pool swale]]
+==Non-structural infiltration practices==
+[[file:Filter strip for bioswale.jpg|thumb|300px|alt=image of filter strip|<font size=3>The vegetated filter strip in this photo is pretreatment for a bioswale. Photo courtesy of Alisha Goldstein, U.S. EPA.</font size>]]
+The practices briefly described in this section are not considered infiltration structures because they do not capture a design volume of water and infiltrate that water at the point of capture. These practices can result in significant volumes of water being infiltrated, however.
+===Harvest and use/reuse systems===
+A stormwater <span title="Rain water harvesting is the practice of collecting rain water from impermeable surfaces, such as rooftops, and storing for future use."> '''[https://stormwater.pca.state.mn.us/index.php?title=Stormwater_and_rainwater_harvest_and_use/reuse harvest and reuse]'''</span> system is a constructed system that captures and retains stormwater for beneficial use at a different time or place than when or where the stormwater was generated. The most common use of retained water is irrigation, but captured water may be used for other purposes, such as indoor toilet flushing. The volume of water potentially infiltrated is a function of the storage capacity of the system. Volumes are restricted to relatively small amounts when tanks are used for storage. Tank storage is commonly used in more urban areas where surface space is restricted. If constructed ponds or wetlands are used for storage, significant volumes of water can be infiltrated through irrigation.
+For more information, see the following sections.
+*[[Stormwater and rainwater harvest and use/reuse]]
+*[[Design considerations for constructed stormwater ponds used for harvest and irrigation use/reuse]]
+===Vegetated filter strips===
+Vegetated filter strips are vegetated areas where stormwater runoff can be directed. As water flows over the filter strip, some infiltration can occur. Infiltration is enhanced by the following conditions.
+*Coarse-textured soils
+*Native perennial vegetation
+*Increased surface roughness
+*Decreased land slope
+*Spreading the runoff over a larger area
+For more information see [[Overview for pretreatment vegetated filter strips]] and [[Design, construction, operation and maintenance specifications for pretreatment vegetated filter strips]].
+===Enhanced turf===
+Infiltration can be enhanced on soils that have been improved or amended. This manual contains limited information on enhanced turf and does not provide guidance for design, construction, maintenance, and assessment of enhanced turf. Information on use of <span title="The product resulting from the controlled biological decomposition of organic materials that has been sanitized through the generation of heat and stabilized to the point that it is beneficial to plant growth"> [https://stormwater.pca.state.mn.us/index.php?title=Compost_and_stormwater_management '''compost''']</span> in soil and credits associated with improved turf can be found on the [[Turf]] page. A discussion of alleviating compaction from construction activities can be found [http://stormwater.pca.state.mn.us/index.php/Alleviating_compaction_from_construction_activities here].
+{{alert|Enhanced turf cannot be used to meet requirements of the [https://stormwater.pca.state.mn.us/index.php?title=Construction_stormwater_program Construction Stormwater General permit] because infiltrated water does not represent an instantaneous volume.|alert-danger}}
+===Swales with no check dams===
+Similar to vegetated filter strips, water can infiltrate into soils underlying swales. The amount of infiltration is typically very low, but can be enhanced by employing the same practices that enhance infiltration in vegetated filter strips.
 ==Unit processes for different infiltration BMPs==
@@ Line 441: / Line 586: @@
 ===Contributing drainage area table===
 The following table provides a summary of recommended contributing drainage area for each stormwater infiltration BMP.
+{{:Contributing drainage area to stormwater BMPs}}
 {{:Stormwater infiltration BMPs - contributing drainage area}}
@@ Line 457: / Line 604: @@
 To see all information contained in the previous tables in a single table, click on the following link: [[Infiltration Summary Table]]
-==Related pages==
+==Related pages for stormwater infiltration==
 *[[Overview of stormwater infiltration]]
 *[[Pre-treatment considerations for stormwater infiltration]]
@@ Line 471: / Line 618: @@
 *[[Potential stormwater hotspots]]
 *[[Stormwater and wellhead protection]]
-*[[Stormwater infiltrations and contaminated soils and groundwater]]
+*[[Stormwater infiltration and contaminated soils and groundwater]]
 *[[Decision tools for stormwater infiltration]]
-*[[Stormwater infiltration research needs]]
 *[[References for stormwater infiltration]]
+==Related pages for infiltration BMPs==
+*[http://stormwater.pca.state.mn.us/index.php/Infiltration Infiltration portal]
+*[[Overview for infiltration]]
+*[[BMPs for stormwater infiltration|Types of infiltration]]
+*[[Design criteria for infiltration]]
+*[[Construction specifications for infiltration]]
+*[[Operation and maintenance of stormwater infiltration practices]]
+*[[Assessing the performance of infiltration]]
+*[[Calculating credits for infiltration]]
+*[[Cost-benefit considerations for infiltration]]
+*[[Case studies for infiltration]]
+*[[External resources for infiltration]]
+*[[References for infiltration]]
+*[[Requirements, recommendations and information for using infiltration basin/underground infiltration BMPs in the MIDS calculator]]
+*[[Understanding and interpreting soils and soil boring reports for infiltration BMPs]]
+*[[Determining soil infiltration rates]]
+*Cold climate considerations for infiltration practices - See [http://stormwater.pca.state.mn.us/index.php/Cold_climate_impact_on_runoff_management#Infiltration], [http://stormwater.pca.state.mn.us/index.php/Cold_climate_impact_on_runoff_management#Infiltration_practices]
 <noinclude>
-[[Category:Infiltration]]
+[[Category:Level 3 - Best management practices/Guidance and information/BMP types and terminology]]
+[[Category:Level 2 - Best management practices/Structural practices]]
 </noinclude>

Difference between revisions of "BMPs for stormwater infiltration" BMPs for stormwater infiltration

Latest revision as of 17:06, 1 February 2023

Contents

Infiltration basin

Infiltration trench

Dry wells (a.k.a. infiltration tubes, french drains, soak-away pits or soak holes)

Underground infiltration systems

Bioinfiltration basin

Permeable pavement

Tree box/Tree trench

Dry swale with check dams

High gradient stormwater step-pool swale with check dams

Non-structural infiltration practices

Harvest and use/reuse systems

Vegetated filter strips

Enhanced turf

Swales with no check dams

Unit processes for different infiltration BMPs

Information tables

Overview table

Contributing drainage area table

Treatment properties table

Selection considerations table

See Infiltration Summary Table

Related pages for stormwater infiltration

Related pages for infiltration BMPs

Difference between revisions of "BMPs for stormwater infiltration"
BMPs for stormwater infiltration