Soil physical properties and processes Soil physical properties and processes

Overview of soil physical properties and associated activities affecting soil physical properties and processes. Click on links to go to a specific section.
Property	Effect on stormwater bmp effectiveness	Processes affected	Desired value	Management strategies
Texture	High	Infiltration, water and air storage and movement	Loams provide good drainage, water storage, and aeration Coarse-textures (e.g. sand, sandy loam) are desired for infiltration bmps	Add clay, silt, sand, or organic matter to amend undesirable soil properties ([1], [2], [3])
Structure	Moderate-high	Infiltration, plant rooting	Well-aggregated soil is generally preferred	Minimize activity in bmp during construction; alleviate compaction; utilize deep-rooting vegetation ([4])
Density	High	Plant rooting, infiltration	1.1 (clays) to 1.5 (sandy loams) g/cm3	Minimize activity in bmp during construction; alleviate compaction; amend soil (e.g. compost) ([5], [6])
Porosity	Moderate-high	Water and air transport	0.42-0.48 cm3/cm3	Minimize activity in bmp during construction; alleviate compaction; amend soil (e.g. compost) ([7], [8])
Consistence	Low	Typically not an important consideration in stormwater applications	Typically not an important consideration in stormwater applications	Typically not an important consideration in stormwater applications
Temperature	Low-moderate	Plant growth and biologic activity	70-80 oC for germination, 65-75 oC after germination	Add soil cover if temperature regulation is desired
Color	Low	Typically not an important consideration in stormwater applications	Typically not an important consideration in stormwater applications	Typically not an important consideration in stormwater applications
Aggregate stability	Moderate	Infiltration, erosion	Tests are generally qualitative; With sieve test, well aggregated soils retain 50 percent or more of the initial soil mass after sieving	Minimize tillage, amend with organic matter, provide soil cover
1 This table provides a general discussion. For detailed information on specific topics, see the links in this table.

Physical properties of soil include color, texture, structure, porosity, density, consistence, aggregate stability, and temperature. These properties affect processes such as infiltration, erosion, nutrient cycling, and biologic activity. These properties also affect suitability of soil for different uses, such as stormwater infiltration, subgrade for roads, and strength for building.

This page provides an overview of soil physical properties, processes they affect, effects of human activities, discussion of stormwater applications, and links to related topics, including information on sampling, testing, and soil health assessments.

Soil physical properties

Soil physical properties include texture, structure, density, porosity, consistence, temperature, and color.

Soil texture

Soil texture triangle showing the USDA classification system based on grain size. Click on image to enlarge.

Soil texture (such as loam, sandy loam or clay) refers to the proportion of sand, silt and clay sized particles that make up the mineral fraction of the soil. Soil texture is determined with one of the following methods.

• Mechanical sieving, if particle size > 0.05 mm
• Sedimentation if size < 0.05 mm. Sedimentation measures the settling rate of particles in liquid medium and relates this rate to the particle mass by use of the Stoke's Law. Forces acting on soil particle are gravitation, buoyancy and drag forces, all of which depend on particle size. Larger particles settle first. The particle mass is determined by density and particle size. Soils must be dispersed prior to measurement. Two methods are commonly used.
  • Hydrometer method (see here for description)
  • Pipette method (see this video for a description)

Other methods are used to determine texture, but these employ qualitative approaches. They include the feel method, ball and ribbon methods, and ball throwing method. These are described here. These methods may be satisfactory for some applications, such as determining if a soil may be suitable for infiltration, but they must be conducted by an experienced person, such as a professional soil scientist.

The following particle size distribution, based on sieve analysis, is commonly used to define soil particles.

• gravel > 2 mm
• sand 0.05 - 2 mm
• very coarse 1 - 2 mm
• coarse 0.5 - 1 mm
• medium 0.25 - 0.5 mm
• fine 0.1 - 0.25 mm
• very fine 0.05 - 0.1 mm
• silt 0.002 - 0.05 mm
• clay < 0.002 mm (< 2 micrometer)

Soil texture describes the distribution of these different size particles in a soil. There are twelve soils based on the distribution of sand, silt and clay. The adjacent image displays the soil texture triangle, which assigns soil type based on the distribution of sand, silt, and clay.

Texture affects many soil processes, including infiltration, drainage (water and air distribution), erosion, chemical processes, and biologic processes. These are discussed generally below.

• Sand: limited structural development, rapid infiltration, rapid drainage, low water holding capacity, leaching of minerals and organic material, reduced chemical and biological processing compared to soils with high clay content
• Silt: poor structural development, moderate infiltration rates, well drained, moderate rates of chemical and biological processing, easily eroded and compacted
• Clay: slow infiltration rates, poorly drained, high water holding capacity, high rates of chemical processing when not compacted or saturated, easily compacted
• Loam: since these are a mixture of sand, silt, and clay, these soils are generally well drained, have good water holding capacity, are chemically and biologically diverse and active

Soil structure

Types of soil structure. Image from Deeproot

This page provides a nice overview and discussion of soil structure.

Soil structure describes the arrangement and organization of soil particles in the soil, and the tendency of individual soil particles to bind together in aggregates. Aggregation affects water and air transport, which affects the movement of solutes and pollutants and affects biologic activity, including plant growth.

The development of soil structure is influenced by

• the amount and type of clay, as well as the exchangeable ions on the clay;
• the amount and type of organic matter, which provides food for soil fungi and bacteria and their secretion of cementing agents (polysaccharides);
• the presence of cementing agents such as iron and aluminum oxides; and
• vegetation, which produces organic matter and binds soil particles together through rooting.

Soil structure is typically divided into one of the following groups, as illustrated in the adjacent image.

• Granular – roughly spherical, like grape nuts. Usually 1-10 mm in diameter. Most common in A horizons, where plant roots, microorganisms, and sticky products of organic matter decomposition bind soil grains into granular aggregates
• Aggregated - this structural type is often not included in classifications, but represents a soil where some granular components have aggregated, but not to the extent found in prismatic or columnar structures.
• Platy – flat peds that lie horizontally in the soil. Platy structure can be found in A, B and C horizons. It commonly occurs in an A horizon as the result of compaction.
• Blocky – roughly cube-shaped, with more or less flat surfaces. If edges and corners remain sharp, we call it angular blocky. If they are rounded, we call it subangular blocky. Sizes commonly range from 5-50 mm across. Blocky structures are typical of B horizons, especially those with a high clay content. They form by repeated expansion and contraction of clay minerals.
• Prismatic – larger, vertically elongated blocks, often with five sides. Sizes are commonly 10-100mm across. Prismatic structures commonly occur in fragipans.
• Columnar – the units are similar to prisms and are bounded by flat or slightly rounded vertical faces. The tops of columns, in contrast to those of prisms, are very distinct and normally rounded.

Soil structure affects water and air movement in soil and is therefore important to soil biota. Platy and massive soils have restricted air and water movement, while granular and aggregated soils have enhanced air and water transport.

Soil structure can be altered by human activity, including the following.

• Compaction, which leads to platy and blocky structure
• Cultivation, which breaks up aggregates in the plow layer but can compact deeper layers
• Removal of vegetation, which reduces aggregation
• Excessive moving and handling of soil, which can destroy aggregates or lead to compaction
• Excessive sodium, often through irrigation, which disperses soil and breaks down structure

Soil density

Example of a dense soil, exhibiting blocky structure. Image:Government of Western Australia

Soil density is related to the mineral and organic composition of a soil and to soil structure. The standard measure of soil density is bulk density, defined as the proportion of the weight of a soil relative to its volume. It is expressed as a unit of weight per volume, and is commonly measured in units of grams per cubic centimeter (g/cm³). Bulk density is an indicator of the amount of pore space available within individual soil horizons, as it is inversely proportional to pore space:

Pore space = 1 – bulk density/particle density

where particle density is the weight/volume of the solid material. Typical particle densities are 2.65 g/cm³ for minerals and 1.3 g/cm³ for organic matter.

For example, at a bulk density of 1.60 g/cm³, pore space equals 0.40 or 40%. At a bulk density of 1.06 g/cm³, pore space equals 0.60 or 60%.

Because of the lower particle density of organic matter compared to minerals, soils with higher concentrations of organic matter have lower bulk densities. Typical bulk densities of different soils are illustrated in the adjacent table.

Comparison of bulk densities for undisturbed soils and common urban conditions. (Source: Schueler, T. 2000. The Compaction of Urban Soils: Technical Note #107 from Watershed Protection Techniques. 3(2): 661-665. Center for Watershed Protection, Ellicott City, MD.)
For information on alleviating soil compaction, see Alleviating compaction from construction activities
Link to this table

Undisturbed soil type or urban condition	Surface bulk density (grams / cubic centimeter
Peat	0.2 to 0.3
Compost	1.0
Sandy soil	1.1 to 1.3
Silty sands	1.4
Silt	1.3 to 1.4
Silt loams	1.2 to 1.5
Organic silts / clays	1.0 to 1.2
Glacial till	1.6 to 2.0
Urban lawns	1.5 to 1.9
Crushed rock parking lot	1.5 to 2.0
Urban fill soils	1.8 to 2.0
Athletic fields	1.8 to 2.0
Rights of way and building pads (85% compaction)	1.5 to 1.8
Rights of way and building pads (95% compaction)	1.6 to 2.1
Concrete pavement	2.2
Quartzite (rock)	2.65

Bulk density affects water and air transport in soils. Soils with high densities resist water and air transport. Soils with high density may also impede root growth.

Several human activities affect bulk density. Soils at construction sites are generally compacted as a result of excavation, mixing, stockpiling, equipment storage, and equipment traffic. In addition, exposed subsoil is susceptible to compaction. Clay soils and wet soils are more susceptible to compaction. Even at sites where selective grading is employed, compaction occurs as a result of construction equipment, stockpiling and vehicle traffic (Randrup, 1998; Lichter and Lindsay, 1994).

When soil is compacted, porosity decreases and bulk density increases. Typical increases in bulk density are shown in the adjacent table, with other compacting activities included for comparison. As a result, permeability of air and water in soil decreases, soil water-holding capacity is reduced, and root growth is impeded. On a watershed scale, soil compaction leads to increased runoff and erosion.

Increase in soil bulk density as a result of different land uses or activities.
Link to this table

Land use or activity	Increase in bulk density (grams / cubic centimeter	Source (link to Reference list)
Grazing	0.12 to 0.20	Smith, 1999
Crops	0.25 to 0.35	Smith, 1999
Construction, mass grading	0.34 to 0.35	Randrup, 1998; Lichter and Lindsey, 1994
Construction, no grading	0.20	Lichter and Lindsey, 1994
Construction traffic	0.17 to 0.40	Lichter and Lindsey, 1994; Smith, 1999; Friedman, 1998
Athletic fields	0.38 to 0.54	Smith, 1999
Urban lawn and turf	0.30 to 0.40	Various sources

The effects of compaction are difficult to overcome and may persist for decades. Natural processes such as freeze-thaw cycles, animal burrowing, and root growth only slowly diminish compaction. These natural processes are typically limited to the upper foot or two of soil. Even when bulk densities decrease, the original soil structure may not be achieved (Randrup, 1997; Schueler and Holland, 2000).

The following table summarizes results for different activities designed to alleviate compaction. The results suggest compost amendment is an effective method for alleviating compaction, while tillage is considerably less effective. Note however, this is an area of on-going research and some recent studies suggest properly conducted tillage can be effective at reducing compaction. For an example, link here.

Reported Activities that Restore or Decrease Soil Bulk Density
Link to this table

Land use or activity	Decrease in bulk density (gms/cc)	Source
Tilling of soil	0.00 to 0.02	Randrup, 1918. Patterson and Bates, 1994
Spedialized soil loosening	0.05 to 0.15	Rolf, 1998
Selective grading	0.00	Randrup, 1998 and Lichter and Linsy, 1994
Soil amendments	0.17	Patterson and Bates, 1994
Compost amendments	0.25 to 0.35	Kolsti et al. 1995
Time	0.20	Legg et al, 1996
Reforestration	0.25 to 0.35	Article 36

Soil porosity

Illustration of porosity in sand, silt, and clay. Image: Penn State College of Agricultural Sciences

Pore space is that part of the bulk volume of soil that is not occupied by either mineral or organic matter but is open space occupied by either gases or water. As discussed above, soil porosity is inversely related to bulk density. In a productive, medium-textured soil the total pore space is typically about 50% of the soil volume. Ranges for soil porosity are shown in the adjacent table. Although porosity does not vary widely across soil textures, values for porosity minus field capacity vary widely, with greater values for coarse-textured soils (e.g. sands). Porosity minus field capacity represents pore space available after water drains from a soil by gravity and is thus considered to be the upper bound of plant available water, with wilting point considered the lower bound.

Although porosity is related to density, pore size is an important factor affecting soil processes. Soils with similar porosity may have different distributions of pore sizes. The smallest pores (<0.1 μm diameter) hold water too tightly for use by plant roots. Plant-available water is held in pores 0.1–75 μm in diameter. Macropores (>75 μm diameter) are generally air-filled when the soil is at field capacity, but they can rapidly transport water and solutes to deeper depths in the soil profile. Clay soils have smaller pores, but more total pore space than sands. Soils with extensive biologic activity have greater macroporosity (e.g. plant roots, animal burrows).

The pore size distribution affects the ability of plants and other organisms to access water and oxygen; large, continuous pores allow rapid transmission of air, water and dissolved nutrients through soil, and small pores store water between rainfall or irrigation events. Pore size variation also promotes biologic activity by compartmentalizing pore space, which reduces competition between organisms, including microbes.

The same human activities affecting soil structure and density affect porosity. Porosity can be enhanced in compacted soils by addition of organic material and through tillage. Macroporosity can be promoted with deeper rooting vegetation.

Recommended values for porosity, field capacity and wilting point for different soils.¹
Link to this table.

Soil	Hydrologic soil group	Porosity 2 (volume/volume)	Field capacity (volume/volume)	Wilting point (volume/volume)	Porosity minus field capacity (volume/volume)3	Field capacity minus wilting point (volume/volume)4
Sand	A (GM, SW, or SP)	0.43	0.17	0.025 to 0.09	0.26	0.11
Loamy sand	A (GM, SW, or SP)	0.44	0.09	0.04	0.35	0.05
Sandy loam	A (GM, SW, or SP)	0.45	0.14	0.05	0.31	0.09
Loam	B (ML or OL)	0.47	0.25 to 0.32	0.09 to 0.15	0.19	0.16
Silt loam	B (ML or OL)	0.50	0.28	0.11	0.22	0.17
Sandy clay loam	C	0.4		0.07
Clay loam	D	0.46	0.32	0.15	0.14	0.17
Silty clay loam	D	0.47 to 0.51	0.30 to 0.37	0.17 to 0.22	0.16	0.14
Sandy clay	D	0.43		0.11
Silty clay	D	0.47		0.05
Clay	D	0.47	0.32	0.20	0.15	0.12

¹Sources of information include Saxton and Rawls (2006), Cornell University, USDA-NIFA, Minnesota Stormwater Manual. (See References for trees)
²Soil saturation is assumed to be equal to the porosity.
³This value may be used to represent the volume of water that will drain from a bioretention media.
⁴This value may be used to estimate the amount of water available for evapotranspiration

Soil consistence (plasticity)

Examples of different soil consistency. Image source

Soil consistence refers to the ease with which an individual ped can be crushed by the fingers. Soil consistence, and its description, depends on soil moisture content. Terms commonly used to describe consistence include the following.

• loose – noncoherent when dry or moist; does not hold together in a mass
• friable – when moist, crushed easily under gentle pressure between thumb and forefinger and can be pressed together into a lump
• firm – when moist crushed under moderate pressure between thumb and forefinger, but resistance is distinctly noticeable Wet soil
• plastic – when wet, readily deformed by moderate pressure but can be pressed into a lump; will form a “wire” when rolled between thumb and forefinger sticky – when wet, adheres to other material and tends to stretch somewhat and pull apart rather than to pull free from other material
• soft – when dry, breaks into powder or individual grains under very slight pressure
• hard – when dry, moderately resistant to pressure; can be broken with difficulty between thumb and forefinger

Soil consistency is useful in estimating the ability of soil to support structures, such as buildings and roads. The measurement is not widely used for stormwater applications.

Soil temperature

Example of daily fluctuations in soil temperature at a Nebraska agricultural station. Image University of Nebraska - Lincoln

Soil temperature is affected by climate, water content of a soil, soil color, soil cover (e.g. presence or absence of mulch), depth in the soil profile, and air and water flow within a soil. Minnesota soils are generally slow to warm in spring due to climate, but the following conditions affect temperature.

• Dark colored soils warm more quickly and attain higher temperatures than light colored soils
• Organic matter imparts a darker color to soil, leading to increased warming, but also retains water, which can slow warming
• Soils with high porosity and well connected pores will warm faster and cool quicker
• Soils on south facing slopes are subject to greater thermal inputs compared to north facing soils
• Soil temperatures fluctuate less with depth in the soil profile
• Soil temperatures fluctuate daily

Soil temperatures are an important consideration in vegetated systems. Human activities that affect temperature include the following.

• Adding organic matter and mulch will slow warming but also increase heat retention
• Activities that improve soil structure, reduce compaction, and increase pore connectivity increase heat transfer
• Vegetation can result in shading
• Light colored soil coverings reflect solar radiation and decrease heating

Soil color

Soil color is largely determined by the organic matter content, drainage conditions, degree of oxidation, and in some cases, presence of specific minerals. Soil color is not a widely used factor in stormwater applications.

Aggregate stability

Aggregate stability refers to the ability of soil aggregates to resist disintegration when disruptive forces associated with tillage and water or wind erosion are applied. Stable soil aggregates, in the presence of water, are important for water and air transport, root growth, habitat for soil biota, minimizing soil erodibility, protecting soil organic matter, and nutrient cycling.

Soil physical processes

Natural soil physical processes typically occur slowly, with the exception of soil temperature (fluctuates daily and seasonally) and color (changes in response to soil moisture). Soil porosity, density, and structure changes in response to biologic activity, as soil biota increases aggregation, creates macropores, and alters organic matter concentrations. These changes are limited to the upper biologically active area within the soil profile. Soil formation is a very slow process, and under natural conditions soil density and structure change slowly.

Humans can greatly accelerate soil physical processes. The major human effects on physical processes are described below.

• Compaction, resulting from a variety of activities, decreases porosity, increases density, and leads to formation of platy or blocky structures. These in turn restrict water and air flow, which in turn adversely impact vegetation and other soil biota. For more information see Alleviating compaction from construction activities.
• Exposure of soil to erosive forces of water and wind, which occurs during construction activities, results in loss of soil, sealing of soil surfaces, and breakdown of surface soil structure. For more information see Soil erodibility, Erosion prevention practices, and Sediment control practices.
• Tillage breaks up soil into smaller aggregates, reduces density, increases porosity, and temporarily disrupts pore connectivity, although it typically promotes biologic activity that eventually improves pore connectivity. For more information see methods for alleviating soil compaction.
• Amendments can improve soil physical properties, particularly the addition of organic material and/or surface coverings (e.g. mulch). Addition of organic matter generally reduces density, improves aggregation and structure, promotes biologic activity, and moderates soil temperature and hydrologic processes. Surface covers such as mulches protect soil from erosive forces, typically improve water retention by reducing evaporation, and moderate soil temperatures. For more information see Stormwater and soil, engineered (bioretention) media, and media amendments.

The above human activities also affect soil hydrologic, chemical, and biologic processes. See the associated web pages for a discussion of these.

Recommended links

• Food and Agricultural Organization
• University of Nevada, Reno
• University of California, Davis
• USDA-NRCS
• Wikipedia
• What is Soil Structure and Why is it Important? - Deeproot
• RHS Gardening
• Soil temperature resources - University of Nebraska, Lincoln